zowieTek PTZ 4K NDI Camera User Guide

zowieTek PTZ 4K NDI Camera User Guide

Introduction

Getting Started

Preparation

Inside the box, please find

1. PTZ Camera
2. Power supply and power cord
3. Remote control
   WARNING: Don’t move or rotate the camera by seizing the camera head.

You also need

1. Two AAA alkaline battery for the remote control
2. Video monitor with HDMI input, or SDI input
3. RJ45 LAN cable.
4. PC or Laptop

Connection

Connect HDMI output as the diagram to video monitor. If you are professional and has SDI monitor, you can also try connect SDI output to the video monitor instead.

Power on

Connect the power supply or you can use Lan cable (802.3at） connect the PoE switcher, press the power switch at the back of the camera. Instantly, you will see the camera starts rotate to its default parking position of front middle.

Now, you will see crystal and beautiful video pictures on the monitor

Note: If no video picture, please

1. Check power supply. Make sure the front LED turn on.
2. Check cable connection and make sure the input video source of the monitor is set correctly

Control the Camera by Remoter

• Put two AAA batteries inside the remote control. Point to the front of the PTZ camera. Use the four arrow buttons to control the pan and tilt. Press HOME always park the camera at the front middle anytime.

• Press ZOOM +/- to change far/near

• Press MENU to set up the camera. For detail camera control by remote control, please refer to chapter 4.5 of the User Manual

Control Camera by Network

Connect the LAN port of camera to the router or switch.

Change PC IP setting

Note: The pictures below are used for reference only, please set according to the actual network condition. IPv4 Address 192.168.1.190 is used as an example, the last segment could be different.

1. Press Win + R then type cmd and Enter,

2. Type ipconfig in the window and Enter.

3. Type ncpa.cpl in the same window and enter.

4. Right-click Local Network connection and select Properties, then double click Internet Protocol Version 4 (TCP/IPv4)

5. Type in IP address, subnet mask and Default gateway found in step 2.

6. Use default gateway as Preferred DNS server address and 8.8.8.8 as Alternate DNS server.
   

7. Click Advanced. Add a new IP address, whose first three segments are the same as camera factory default IP address (192.168.100.88). Type 192.168.100.50 for example. Subnet mask remains default.
   

8. Save settings

Web login and control

Now, you can access the camera, open web browser, type IP address 192.168.100.88, then Enter to go to the camera login page.

• User name: admin
• Password: admin
• At this time, you can see the preview of camera video. Do the pan, tilt and zoom control via LAN. For detail advanced network and control, please refer to chapter 6.4 of the User Manual.

Change the IP of camera

For future convenient, change the IP of camera to the same IP segment of your LAN, for example 192.168.1.188. The Gateway also needs to be changed as follow: 192.168.1.1. Then, click Submit.
Restart the Camera.

NOTE: Above IP address cannot be the same with any other computers or devices in the LAN. If forget the IP one day, note that it will show on the left top corner of video in seconds when power on each time

MAC PC IP setting

Click + button on the left-bottom corner to add 2nd Ethernet IP at 192.168.100.xx segment, then you can access the camera.

Please read this guide and FAQ before returning this product for any reasons.

Customer Support

A professional video camera, streaming, recording solution provider Since 2004
18 Hunan Road, West Wing 1701
Pudong, Shanghai 201204
PN: 904XY-960
Jul. 2022
www.zowietek.com
www.zowietek.com/documents
www.zowietek.com/faq
NDI® is a registered trademark of NewTek, Inc. and is authorized to zowietek

References

• Documents - Zowietek Electronics, Ltd.
• FAQ - Zowietek Electronics, Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>