ZowieTek AI Tracking PTZ Camera 20X User Manual
- June 10, 2024
- zowieTek
Table of Contents
AI Tracking PTZ Camera 20X
User Manual
AI Tracking PTZ Camera 20X
Getting Started
Preparation
Inside the box, please find
- PTZ Camera
- Power supply and power cord
- Remote control
WARNING: Don’t move or rotate the camera by seizing the camera head.
You also need
- Two AAA alkaline battery for the remote control
- Video monitor with HDMI input, or SDI input
- RJ45 LAN cable.
- PC or Laptop.
Connection
Connect HDMI output as the diagram to video monitor. If you are professional
and has SDI monitor, you can also try connect SDI output to the video monitor
instead.
Power on
Connect the power supply or you can use Lan cable (802.3at) connect the PoE
switcher, press the power switch at the back of the camera. Instantly, you
will see the camera starts rotate to its default parking position of front
middle.
Now, you will see crystal and beautiful video pictures on the monitor.
Note: If no video picture, please
- Check power supply. Make sure the front LED turn on.
- Check cable connection and make sure the input video source of the monitor is set correctly.
Control the Camera by Remoter
Put two AAA batteries inside the remote control. Point to the front of the PTZ camera. Use the four arrow buttons to control the pan and tilt. Press HOME always park the camera at the front middle anytime. Press ZOOM +/- to change far/near. Press MENU to set up the camera. For detail camera control by remote control, please refer to chapter 4.5 of the User Manual
Control Camera by Network
Connect the LAN port of camera to the router or switch.
Change PC IP setting
Note: The pictures below are used for reference only, please set
according to the actual network condition. IPv4 Address
192.168.1.190 is used as an example, the last segment
could be different.
-
Press Win + R,then type cmd and Enter.
-
Type ipconfig in the window and Enter.
-
Type ncpa.cpl in the same window and enter.
-
Right-click Local Network connection and select Properties, then double click Internet Protocol Version 4 (TCP/IPv4).
-
Type in IP address, subnet mask and Default gateway found in step 2.
-
Use default gateway as Preferred DNS server address and 8.8.8.8 as Alternate DNS server.
-
Click Advanced. Add a new IP address, whose first three segments are the same as camera factory default IP address (192.168.100.88). Type 192.168.100.50 for example. Subnet mask remains default.
-
Save settings.
Web login and control
Now, you can access the camera, open web browser, type IP address
192.168.100.88, then Enter to go to the camera login
page.
User name: admin
Password: admin
At this time, you can see the preview of camera video. Do the pan, tilt and
zoom control via LAN. For detail advanced network and control, please refer to
chapter 6.4 of the User Manual
Change the IP of camera
For future convenient, change the IP of camera to the same IP segment of your
LAN, for example 192.168.1.188. The Gateway also needs
to be changed as follow: 192.168.1.1. Then, click
Submit. Restart the Camera.
NOTE: Above IP address cannot be the same with any other computers or
devices in the LAN. If forget the IP one day, note that it will show on the
lefttop corner of video in seconds when power on each time.
MAC PC IP setting
Click + button on the left-bottom corner to add 2nd Ethernet IP at
192.168.100.xx segment, then you can access the
camera. Please read this guide and
FAQ before returning this product for any
reasons.
A professional video camera, streaming, recording solution provider Since 2004
Zowietek Electronics, Ltd.
2218 Hunan Road, West Wing 1701
Pudong, Shanghai 201204
PN: 904XY-9Z0
Oct. 2022
www.zowietek.com
www.zowietek.com/documents
https://www.zowietek.com/knowledge-base/
NDI® is a registered trademark of NewTek, Inc. and is authorized to zowietek
Zowietek Electronics, Ltd.
Printed in China.
20220727
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>