ZowieTek V10 USB HD Video Conference Camera User Manual

June 2, 2024
zowieTek

ZowieTek V10 USB HD Video Conference Camera

Safety Precautions

  • During the installation and operation, all electrical safety regulations of the country and region of use must be strictly observed.
  • Please use the power adapter that comes standard with this product.
  • Do not connect multiple devices to the same power adapter (exceeding capacity of the adapter may generate excessive heat or cause fire).
  • Do not rotate the camera by hand, otherwise it may cause mechanical failure.
  • When installing this product on a wall or ceiling, make sure the device securely and there are no obstacles within the rotation range; Do not power on until all installations are completed.
  • To avoid heat build-up, please keep smooth ventilation around the device.

Packing List

  • Camera 1
  • Power Adapter 1
  • USB Cable 1
  • Remote Control 1
  • User Manual 1

Quick Start

  1. Please check connections are correct before starting.ZowieTek V10 USB HD Video Conference Camera 1
  2. Connect the power adapter to the power connector on the rear panel of the camera. The power indicator on the front panel of the camera turns on.
  3. After the camera is powered on, it starts to initialize, right up to the limit position, and then both horizontal and vertical go to the middle position. When the motor stops running, it indicates the initialization is completed.

About Product

Features

  • Full Featured USB Interface
    Full featured USB interface, compatible with USB3.0 and USB2.0, support audio and encoding output, support UVC 1.1 protocol.

  • 1080P Full HD
    The new 1/2.8-inch high-quality HD CMOS sensor with 2.07 million effective pixels enables high-quality images up to 1920×1080. Output frame rate is up to 60 frames/s to present clear and realistic HD video, vividly showing the expression and action of the characters.

  • 72.5° Wide-angle Lens
    The exclusively customized 72.5° high-quality ultra-wide-angle lens with optical zoom up to 12x.

  • Low Illumination
    The new CMOS image sensor with ultra-high SNR can effectively reduce the image noise under low illumination. The application of 2D and 3D noise reduction algorithm greatly reduces the image noise even under the condition of ultra- low illumination, it keeps the picture clean and clear, and the SNR of image is as high as 55dB.

  • Remote Control
    The camera can be controlled remotely through the RS232, network and USB port.

  • Leading Auto Focus Technology
    Using the advanced focusing algorithm and ToF module assists focusing, lens can focus quickly, accurately and stably.

  • Multiple & Complete Interfaces
    Support audio and video output via HDMI, USB3.0 and network interface.

  • Portrait
    Support portrait output.

  • Easy to Use
    No need to download the driver, plug and play USB output to take a convenient and simple user experience.

  • Multiple Power Supply Modes
    Simultaneously support USB 5V, DC 12V power supply.

Specifications

Camera

Video System| 1080P60, 1080P50,

1080P30, 1080P25,

720P60, 720P50

Sensor| 1/2.8-inch, CMOS,

Effective Pixel: 2.07M

Scanning

Mode

| Progressive
Lens| 12x, f=3.5mm ~ 42.3mm,

F1.8 ~ F2.8

Minimum

Illumination

| 0.5 Lux @ (F1.8, AGC ON)
Shutter| 1/30s ~ 1/10000s
White Balance| Auto, Indoor, Outdoor,

One Push, Manual, VAR

Backlight

Compensation

| Support
Digital Noise

Reduction

| 2D&3D Digital Noise

Reduction

SNR| ≥55dB
Horizontal

FOV

| 72.5° ~ 6.9°
---|---
Vertical FOV| 44.8° ~ 3.9°
Pan Angle| ±170°
Tilt Angle| -30° ~ +90°
Pan Speed| 2.7° ~ 35.7°/s
Tilt Speed| 2.7° ~ 31.5°/s
Image Flip| Support
Image Freeze| Support
Preset Position| 255
Preset

Accuracy

| 0.1°
USB Features
Operate System| Windows 7, Windows 8, Windows 10, Mac OS X,

Linux, Android

Color System/

Compression

| H.264/YUY2/MJPEG

Video Format

| l H.264: 1080P@60fps

(max.)

l YUY2 (ISOC): 1080P@60fps (max.)

l MJPEG: 1080P@60fps

(max.)

USB Audio| l Support
USB Protocol| UVC 1.1
UVC PTZ

Control

| Support
Network Features
Encode

Protocol

| H.264/MJPEG
Video Stream| First Stream, Second

Stream

First Stream

Resolution

| 1920×1080, 1280×720
Second Stream

Resolution

| 1280×720, 640×360
Video Bit Rate for First

Stream

| 32Kbps ~ 20480Kbps
Video Bit Rate

for Second

| 32Kbps ~ 6144kbps
Stream|
---|---
Bit Rate

Control

| CBR, VBR
Frame Rate| 50Hz: 1fps ~ 50fps

60Hz: 1fps ~ 60fps

Audio Type| AAC
Audio Bit Rate| 96K, 128K, 256K
Protocol| TCP/IP, HTTP, RTSP, RTMP(S), ONVIF, DHCP,

SRT, Multicast, etc.

Interfaces

USB Interface| 1 x USB3.0: Type-C
1 x USB2.0: Type-A
Network

Interface

| 1 x NET: 10M/100M

adaptive ethernet port

Video

Interface

| 1 x HDMI: 1.4b
Audio

Interface

| 1 x LINE IN: 3.5mm audio

interface


Communicatio n Interface

| 1 x RS232: 8pin min DIN, Max. Distance: 30m, Protocol:

VISCA/Pelco-D/

Pelco-P

Power

Interface

| JEITA (DC 12V)/

USB Type-C (USB 5V)

General Specifications
Input Voltage| DC 12V /USB 5V
Input Current| 12V 1.0A (max.)/

5V 1.5A (max.)

Operating

Temperature

| 0°C ~ 40°C
Storage

Temperature

| -40°C ~ 60°C
Power

Consumption

| 12W (max.)
Dimension

(mm)

| 144 x 144 x 165.4
Net Weight| About 1.4Kg

Product features and specifications are subject to change without notice.

Interfaces and Buttons

No. Interface
1 NET Interface
2 HDMI Interface
3 RS232 Interface
4 USB3.0 Interface
5 LINE IN Interface
6 USB2.0 Interface
7 DC 12V Interface

Dimension

ZowieTek V10 USB HD Video Conference Camera 3ZowieTek V10 USB HD Video Conference Camera
4

Installation

ZowieTek V10 USB HD Video Conference Camera 5

ZowieTek V10 USB HD Video Conference Camera 6

The installation diagram is for reference only. The brackets and screws are not standard. For packing accessories, please refer to the actual product.

Remote Control

ZowieTek V10 USB HD Video Conference Camera 7

  1. (Standby) Key
    Press to enter standby mode

  2. Number Keys
    To set preset or call preset

  3. Key
    Use with other keys

  4. PRESET Key
    Set preset: [PRESET] + Number key (0-9)

  5. HOME Key
    Confirm selection or press to turn PTZ back to the middle position

  6. (Return) Key
    Press to return to the previous menu

  7. ZOOM Keys

    • SLOW: Zoom In [+] or Zoom Out [-] slowly
    • FAST: Zoom In [+] or Zoom Out [-] fast
  8. L/R SET Key

    • Standard: Simultaneously press L/R SET + 1
    • Reverse: Simultaneously press L/R SET + 2
  9. FOCUS Keys
    Auto/Manual/Far-end/Near-end focus

  10. CAMERA SELECT Keys
    Press to select and control the camera

  11. Key
    Use with other keys

  12. IR Remote Control Keys

    • [*] + [#] + [F1]: Address 1
    • [*] + [#] + [F2]: Address 2
    • [*] + [#] + [F3]: Address 3
    • [*] + [#] + [F4]: Address 4
  13. RESET Key
    Clear the preset position: [RESET] + Number key (0-9)

  14. PTZ Control Keys
    PTZ moved according to the arrow indicates

  15. MENU Key
    Enter or exit OSD menu

  16. BACKLIGHT Key

Backlight ON/OFF: Press repeatedly to enable or disable the backlight compensation

NOTE:

  • Effective only in auto exposure mode
  • If there is a light behind the subject, the subject will become dark, press the backlight key to enable the backlight compensation. Press again to disable this function

GUI Settings

MENU
Press [MENU] key to display the main menu. Use the arrow key to move the cursor to desired item and press the [HOME] key to confirm to enter the corresponding sub-menu.

EXPOSURE
When in main menu page, move the cursor to [Exposure] and press [HOME] key to confirm to enter the Exposure page as shown as below.

  • Mode : Auto, Manual, SAE, AAE, Bright.
  • ExpCompMode (Exposure Compensation Mode): On, Off (Effective in Auto mode).
  • ExpComp (Exposure Compensation Value): -7 ~ +7 (Effective in ExpCompMode On).
  • Backlight : On, Off (Effective in Auto mode).
  • Bright : 0 ~ 17 (Effective in Bright mode).
  • Gain Limit : 0 ~ 15 (Effective in Auto, SAE, AAE, Bright mode).
  • AntiFlicker : Off, 50Hz, 60Hz (Effective in Auto, AAE, Bright mode).
  • Meter : Average, Center, Smart, Top (Effective in Auto, SAE, AAE, Bright mode).
  • Iris : F1.8, F2.0, F2.4, F2.8, F3.4, F4.0, F4.8, F5.6, F6.8, F8.0, F9.6, F11.0, Close (Effective in Manual, AAE mode).
  • Shutter : 1/30 ~ 1/190 (Effective in Manual, SAE mode).
  • Gain : 0 ~ 7 (Effective in Manual mode).
  • DRC : 0 ~ 8.

COLOR
When in main menu page, move the cursor to [Color] and press [HOME] key to confirm to enter the Color page as shown as below.

  • WB-Mode (White Balance Mode) : Auto, Indoor, Outdoor, One Push, Manual, VAR.
  • RG Tuning (Red Gain Tuning) : -10 ~ +10 (Effective in Auto, One Push, VAR mode).
  • BG Tuning (Blue Gain Tuning) : -10 ~ +10 (Effective in Auto, One Push, VAR mode).
  • Saturation : 60% ~ 200%.
  • Hue : 0 ~ 14.
  • AWB Sens (The White Balance Sensitivity) : Low, Middle, High (Effective in Auto, One Push mode).
  • RG (Red Gain): 0~255 (Effective in Manual mode).
  • BG (Blue Gain): 0~255 (Effective in Manual mode).
  • Color Temp: 2500K ~ 8000K (Effective in VAR mode).

IMAGE
When in main menu page, move the cursor to [Image] and press [HOME] key to confirm to enter the Image page as shown as below.

  • Luminance: 0 ~ 14.
  • Contrast: 0 ~ 14.
  • Sharpness: Auto, 0 ~ 15.
  • Flip-H: On, Off.
  • Flip-V: On, Off.
  • B&W-Mode: On, Off.
  • Gamma: Ext, Default, 0.45, 0.5, 0.56, 0.63.
  • Style: Default, Beauty, Jewelry, Clothing, Sears, Food.

P/T/Z
When in main menu page, move the cursor to [P/T/Z] and press [HOME] key to confirm to enter the P/T/Z page as shown as below.ZowieTek V10 USB HD Video
Conference Camera 12

ZowieTek V10 USB HD Video Conference Camera 13

  • SpeedByZoom (The Depth of Field Ratio): On, Off.
  • AF-Zone (Auto Focus Area): Front, Top, Center, Bottom.
  • AF-Sense (Auto Focus Sensitivity): Low, Normal, High.
  • Display Info: On, Off.
  • Image Freeze: On, Off.
  • Call Preset Speed: 1 ~ 24.
  • Pre Zoom Speed: 0 ~ 7.

NOISE REDUCTION
When in main menu page, move the cursor to [Noise Reduction] and press [HOME] key to confirm to enter the Noise Reduction page as shown as below.

ZowieTek V10 USB HD Video Conference Camera 14

  • NR2D Level (2D Noise Reduction): Auto, Off, 1 ~ 5.
  • NR3D Level: (3D Noise Reduction): Auto, Off, 1 ~ 8.

SETUP
When in main menu page, move the cursor to [Setup] and press [HOME] key to confirm to enter the Setup page as shown as below.

  • Language: EN, Chinese, Russian.
  • Video Format: 1080P60, 1080P50, 1080P30, 1080P25, 720P60, 720P50.
  • USB Mode: ISOC, BULK.
  • USB Audio: On, Off.
  • Aux Focus: On, Off.
  • UVC H264: On, Off.

The setting of USB Format, USB Mode and UVC H264 will take effect after press the [HOME] key to confirm to restart the device.

COMMUNICATION SETUP
When in main menu page, move the cursor to [Communication Setup] and press [HOME] key to confirm to enter the Communication setup page as shown as below.

  • Protocol: Auto, VISCA, PELCO-D, PELCO-P.
  • V_Address: 1 ~ 7 (Effective in Auto, VISCA protocol).
  • V_AddrFix: On, Off (When set to On, the 88 30 01 FF command does not work. Effective in Auto and VISCA protocol).
  • P_D_Address: 0 ~ 254 (Effective in Auto, PELCO-D protocol).
  • P_P_Address: 0 ~ 31 (Effective in Auto, PELCO-P protocol).
  • Net Mode (Set the Serial Port Network Control): Serial, Paral (Effective in Auto, VISCA protocol).
  • Baudrate: 2400, 4800, 9600, 38400.

RESTORE DEFAULT
When in main menu page, move the cursor to [Restore Default] and press [HOME] key to confirm to enter the Restore Default page asshown as below.

Restore : Yes, No.

Notice : When selected “Yes” and confirm with [HOME] key, all parameters will restore to default, include the IR Remote address and VISICA address. GUI menu and device information are subject to N ote change without notice.

WEB Settings

Access Camera
Access http://192.168.100.88 to pop up the login window, then input username (default: admin) and password (default: admin). After login, it will show as below:ZowieTek V10 USB HD Video Conference Camera 18

Control Camera

All pages include two menu bars:

  • Real Time Monitoring: Video image displaying with function buttons.
  • Parameter Setup: Parameter configurating.
  • A. Video Viewing Window
    The video viewing window is same as video resolution, the bigger the resolution, the bigger the playing area. Double click the viewing window to show full screen, double click again, to return to initialized size.

Status bar in viewing window shown as below:

ZowieTek V10 USB HD Video Conference Camera 19

  1. Video Pause: Click to pause the real-time video, click again to resume.
  2. Audio Control: Click to adjust the volume or mute.
  3. Full screen switch button.

B. PTZ Setup

ZowieTek V10 USB HD Video Conference Camera 20

  1. Pan and Tilt Control
    The direction arrows and HOME button allow you to manually drive the camera to desired position.

  2. Zoom
    Zoom In and Zoom Out buttons allow for wide or narrow view of the space.

  3. Focus
    Focus In and Focus Out button allow for fine manual focus adjustment if the camera has any auto focusing problems on difficult object.

  4. PTZ Speeds
    Pan speed rate can be set to 1 ~ 24, Tilt speed rate can be set to 1 ~ 20. Zoom and Focus speed rate can be set to 1 ~ 7.

  5. PTZ Presets
    When the PTZ turns to the position that you would like to return to later, you can set presets for quick recall. Type a number (0 ~ 254) into the preset box and click “Set” button to save. When the PTZ turn to other position, input the preset number and click “Call” button to turn the PTZ back to the preset position.

  6. PTZ/OSD
    Move the cursor to dropdown menu, select and click “OSD” to open the on-screen menu and do menu settings on the interface.

C. Language Selection

Click to select “Chinese” or “English” to change the language of the webpage.

Video Settings

ZowieTek V10 USB HD Video Conference Camera 22

  1. Video Format
    Support 50Hz (PAL) and 60Hz (NTSC) formats.

  2. Encode Level
    Support baseline, mainprofile and highprofile.

  3. Encode Codec
    Support H264, H265 and MJPEG

  4. Resolution
    First stream support 1920×1080, 1280×720. Second stream support 1280×720, 640×360; The bigger the resolution, the clearer the image, and the larger the code stream, the more network bandwidth will be taken.

  5. Bit Rate
    You can specify the bit rate, the larger of the bit rate, the clearer of the image. The configuration of the bit rate needs to be combined with the network bandwidth. When the network bandwidth is narrow and the bit rate is configured larger, the video stream cannot be transmitted normally, and the visual effect will be worse.

  6. Frame Rate
    You can specify the size of the frame rate, the greater the frame rate, the smoother the image, the smaller the frame, the more sense of beating.

  7. I Key Frame Interval
    Set the interval between two I frames, the bigger the interval, the slower the response when opening the image for the first time.

  8. Bit Rate Control
    Two modes for bit rate control:
    CBR (Constant Bit Rate): Video coder will be coding according to the preset speed.
    VBR (Variable Bit Rate): Video coder will adjust the speed based on preset speed to gain the best image quality.

  9. Slice Split Enable
    Select to turn On/Off the Slice Split Enable function.

  10. Split Mode
    Split Mode Fixed bytes.

  11. Slice Size
    Size for slice.

Image Settings

ZowieTek V10 USB HD Video Conference Camera 23

  1. Luminance
    Image Luminance: 0~14 (Default is 7).

  2. Contrast
    Image Contrast: 0~14 (Default is 7).

  3. Sharpness
    Image Sharpness: 0 ~ 15, Auto (Default is 5).

  4. Gamma
    Gamma Option: Default, 0.45, 0.50, 0.56, 0.63, Ext.

  5. Black & White
    Black & White Option: Colorful, Black & White.

  6. Flip-H
    Select to turn On/Off the Flip-H function.

  7. Flip-V
    Select to turn On/Off the Flip-V function.

Audio Settings

  1. Audio Switch
    Select to turn On/Off Audio Switch.

  2. Audio Type
    Audio type AAC.

  3. Sample Rate
    Sample rate 32K.

  4. Bit Rate
    Bit rate 96K, 128K and 256K selectable.

  5. Input Type
    Input type Line in.

  6. ADTS Options
    Select to turn On/Off ADTS Options.

System Settings

  1. Reboot
    Click “Reboot” to restart system.

  2. Username and Password
    Modify the password of username and guest (use letters and Numbers only).

Network Settings

ZowieTek V10 USB HD Video Conference Camera 26

ZowieTek V10 USB HD Video Conference Camera 27

  1. Lan Settings
    The default the IP address is 192.168.100.88, the MAC address cannot be modified.

  2. Port Settings

    • A. HTTP Port
      The IP address identifies a network device and multiple network programs can run on the device, each network program uses the network port for data transmission. The port setting on this page is to set up which port the WEB SERVER program uses to transmit. During port mapping, it needs to be consistent with the port number (default is 80).

    • B. RTSP Port
      Set up the RTSP port, default is 554.

    • C. TCP Port
      Set up the TCP port, default is 5678.

    • D. UDP Port
      Set up the UDP port, default is 1259.

    • E. Sony Visca
      Sony Visca 52381.

  3. RTMP(S) Settings
    Set the MRL of RTMP(S) and select “on”, “off”, “video” and “audio” functions to enable or disable video and audio in the two streams.

  4. SRT Settings
    Turn On/Off SRT and set up the SRT Mode, SRT Server, SRT Port, SRT Encryption, SRT Password, SRT Bandwidth Overhead, SRT Variable Latency and SRT StreamID.

  5. RTSP Settings
    Turn On/Off the RTSP Auth.

  6. ONVIF Settings
    Turn On/Off the ONVIF and ONVIF Auth.

  7. Multicast Settings
    Turn On/Off Multicast, set up the Multicast Address (default is 224.1.2.3) and Port (default is 6688; 6688 is the multicast port of the first stream and 6690 is the multicast port of the second stream).

  8. NTP Settings
    Turn On/Off NTP time sync, Main time show and Sub time show; select the Time Zone; set up the Server address, Time interval and the Time Show Position of the two streams.

Device Information

Download the Upgrade Program
If you need the camera upgrade program, please contact the manufacturer. WEB interface and device information are subject to change without notice.

Troubleshooting

Image

  • The monitor shows no image
1. Ensure that the camera power supply is connected, the voltage is normal, and the power indicator is always on.
2. Turn off the power switch to check that the camera is self-testing.
3. Ensure the cable of video platform and TV that in correct connection.
  • Image jitters after the camera is properly connected
1. Ensure that the camera installation is in stable position.
2. Check that any vibrating machinery or object near the camera.
  • There is no video image in browser
    IE browser does not support H5, you need to use VLC plug-in to view videos. Please access VLC website (http://www.videolan.org/vlc) to download and install the 32-bit VLC media player, after installation, the video image will be displayed normally when access the camera. Other mainstream browsers already support H5 and do not need to install the VLC plug-in.

  • Unable to access through the browser

1. Using PC to access the network to test that the network access can work properly to eliminate the network fault caused by cable and PC virus until the PC and camera can ping each other.
2. Disconnect the network, connect camera with PC separately and reset the IP address of PC if necessary.
3. Ensure that the IP address, subnet mask and gateway settings is correct.
4. Check that the MAC address is conflicts.
5. Check that the web port is modified, the default setting is 80.
  • Forget the IP address or login password
    The default IP address is: 192.168.100.88; the default username and password are: admin.

Control

  • Remote control does not work
1. Check and replace with new batteries.
2. Ensure that the camera working mode is correct.
3. Ensure that the address key of remote control can match the camera.
  • Serial port cannot control
1. Ensure that the protocol, address and bit rate of the camera are consistent.
2. Ensure that the control cable is properly connected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals