V I V O STAND-TS38B-4 Telescoping Quad Monitor Desk Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
V I V O STAND-TS38B-4 Telescoping Quad Monitor Desk Mount
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR BACKWARD.
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
- Phillips Screwdriver
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury
ASSEMBLY STEPS
STEP 1
Install Bottom Pole (A) to Base (D) using M5x16 Screws (S-A). Tighten with the 3mm Allen wrench (T-A).
STEP 2
Thread Middle Pole (B) onto Bottom Pole (A), and Top Pole With Cap (C) onto Middle Pole (B).
STEP 3
Install Arms (F) to Arms with Pole Collar (E) using M8x42mm Screws (S-B) and the 5mm Allen Wrench (T-B). Ensure the tilt joints are facing in the same direction during installation.
STEP 4
Slide Pole Cable Clips (H) and arm assemblies onto the pole assembly. Secure arm assemblies using 6mm Allen Wrench (T-C). Attach Arm Cable Clips (I) to arms.
STEP 5
OPTION A: Flat Back Monitor
Attach the VESA Plates (G) to the monitor with Thumbscrews (M-A).
NOTE: Hand tighten screws to avoid over tightening.
OPTION B: Curved Back Monitor
Attach VESA Plate (G) to the monitor with M4x30mm Screws (M-B) and M4 Spacers (M-C).
NOTE: Gently tighten using a screwdriver
STEP 6
Slide VESA Plates (G) onto the arm assemblies. The monitors can be leveled using 3mm Allen Wrench (T-A). Secure using M6 Cap Nuts (S-C).
STEP 7
Adjust the length of arm assemblies using 3mm Allen Wrench (T-A).
STEP 8
Manage cables using Arm Cable Clips (I) and Pole Cable Clips (H).
STEP 9
Adjust the tilt using 5mm Allen Wrench (T-B).
SKU: STAND-TS38B-4
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual https://vivo- us.com/products/stand-ts38b-4
CUSTOMER SUPPORT
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
GET IN TOUCH | Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---
www.vivo-
us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com| AVG. RESPONSE TIME (within office
hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3h
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Telescoping Quad Monitor Desk Stand – VIVO - desk solutions, screen mounting, and more