rizoma Vespa Elettrica Adjustable Plus Brake Levers Installation Guide
- June 12, 2024
- rizoma
Table of Contents
**rizoma Vespa Elettrica Adjustable Plus Brake Levers Installation Guide
**
Welcome to Rizoma
Before you start
We are pleased to welcome you into the world of RIZOMA, and we congratulate
you for your excellent choice. Please carefully follow the instructions in
this guide, which will allow you to mount and use the product correctly and
enjoy all the features it has. For your protection and safety, RIZOMA
expressly recommends that you have the installation of the product performed
by skilled personnel. Improper installation, repair or maintenance, can cause
accidents. Keep this user guide as a reference for the future. RIZOMA accepts
no liability for any damage, of any kind, which may be caused, directly or
indirectly, to persons or things as a result of incorrect assembly or failure
to observe all the assembly instructions. We also invite you to comply with
the provisions of the Highway Code and Traffic rules and/or to additional
regulations in force in your Country
General conditions
Attention: This component comes assembled for shipping purposes only. Tighten all fasteners to appropriate torque specifications before riding.
Descriptions preceded by this symbol contain information, instructions, or procedures, which, if not followed, may result in death or serious injury.
1. Carefully read, understand and follow these instructions, they are an
essential part of the product. If you have any doubt whatsoever regarding the
installation or use of your RIZOMA product, please see your authorized RIZOMA
dealer for assistance (on www.rizoma.com).
2- For correct installation, all tightening has to be done after the correct
positioning of the accessories without restricting the moving parts, to not
compromise the correct functioning of the product.
3-After installing any Rizoma product, please check that all related
components of the motorbike function e.g. brakes, throttle, clutch, lights and
steering. We strongly suggest to repeat these checks periodically, especially
after long trips or prolonged periods of not using the bike.
Your RIZOMA products require regular inspection and maintenance. The more you ride the more often you must inspect your RIZOMA products. If your products are leaking, bent, deformed, cracked, chipped or worn, no matter how slight, immediately have a RIZOMA dealer inspect the products before you ride again. In any case never try to repair or modify the Rizoma products or their components, always replace with Rizoma original components.
Rizoma products may not be compatible with your motorcycle or with other aftermarket equipment installed before. For your safety Rizoma suggests to always contact your RIZOMA dealer.
Brake levers kit
Consult the website www.rizoma.com, in Brake/Clutch levers “ADJUSTABLE PLUS” section click “DOWNLOAD” to download the PDF document approval ABE.
Before you start mounting the product please check the completeness of the kit on the part list. The difficulty level and the time of assemblage shown do not include the removal of OEM components.
Warning: Make sure that your motorbike is standing firmly before you start work, as a fall may lead to damage to the motorbike or injury to you or others. WARNING: TO CLEAN YOUR PRODUCT DON’T
USE DETERGENT, AGGRESSIVE PRODUCTS OR ABRASIVE SPONGE THAT CAN DAMAGE OR SCRATCH YOUR PRODUCT, BUT USE ONLY NEUTRAL DETERGENT WITH COLD WATER.
Improper installation of lever could adversely affect performance of brakes or clutch, resulting in an accident, personal injury or death. Your lever is equipped with a safety ball at the end to prevent impalement in the event of a crash. Never ride if the lever is broken or otherwise damaged in any way. Immediately replace the lever.
Tools Package
10 mm
10 mm
3 mm
DIFFICULTY LEVEL
Facile Simple
TIME OF ASSEMBLAGE 25-30 min
INSTALL ORIGINAL SPRING
ATTENTION: BEFORE TO INSTALL THE BRAKE LEVER REMOVE THE FRONT HANDLEBAR COVER (REFER TO THE VEHICLE WORKSHOP MANUAL). REMOVE THE ORIGINAL BRAKE LEVER AND KEEP THE SCREW, SPRING AND NUT
INSTALL REAR BRAKE LEVER
INSTALL FRONT BRAKE LEVER
ATTENTION: BEFORE TO INSTALL THE BRAKE LEVER REMOVE THE FRONT HANDLEBAR COVER (REFER TO THE VEHICLE WORKSHOP MANUAL). REMOVE THE STANDARD BRAKE LEVER RETAINING PIN AND KEEP THE SCREW AND NUT
ADJUSTMENT BRAKE LEVER
ATTENTION: ROTATE THE ADJUSTER CLOCKWISE OR COUNTERCLOCKWISE TO MOVE THE BRAKE LEVER IN OR OUT.
ATTENTION: ACTING ON THE END PART OF THE LEVER CAN ADJUST THE LENGTH OF THE LEVER. AFTER THE ADJUSTMENT CHECK THAT THE LEVER ON ANY POSITION DON’T TOUCH NONE PARTS OF THE MOTORCYCLE.
WARNING: TO CLEAN THE 0-RING DON’T USE HYDROCARBONS.
Warnings
RIZOMA reserves the right, in its sole discretion, to make changes to the product and this information at any time and without prior notice. Although many catalogs and advertisements depict riders engaged in extreme or stunt riding, this activity is extremely dangerous, increases the risk of an accident, and increases the severi ty of any injury.
The action depicted is performed by professionals under strictly controlled riding conditions. Only you know the limits of your riding ability and only you can control the conditions under which you ride. By and in consideration for his/her purchase and use of the RIZOMA product, the user expressly recognizes and agrees that in the event of any claim arising out of the use of this RIZOMA product, whether such claim is based in contract, warranty, tort (personal injury or wrongful death) or otherwise, the laws of the Republic of Italy shall apply and jurisdiction and venue for any such action shall be in the Courts of Busto Arsizio, Italy.
All riders are strongly urged to take a motorcycle rider safety clinic. Always wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a full face helmet), that has been approved by ANSI , SNELL, CE, or any other relevant authority, and any other safety equipment necessary for your riding style, such as full finger gloves, boots, and body armor.
Be sure to read and follow all the instructions and warnings that originally accompanied your motorcycle, as well as the literature that accompanied any other component parts installed on your motorcycle.
Be sure that your tires are inflated to the correct pressure and that there is no damage whatsoever in the tread or sidewall of the tire.
Legal notes
Some of our products may not be approved for road circulation in the countries where homologation is required. Thus RIZOMA® srl declines any responsibility for a different use of its products.