SCOSCHE BTFREQ Handsfree Car Kit with FM Transmitter User Manual
- June 12, 2024
- Scosche
Table of Contents
DEVICE SETUP
SECTION A – Overview
SECTION B – Power Up & Bluetooth Pairing SECTION
C – Connecting to your Car’s Stereo
SECTION D – Reconnect to your Device
SECTION E – Streaming Music
SECTION F – Making a Call
SECTION 6 – Receiving a Call
SECTION H – Voice Assistant Activation & Dual-Port USB Charger
SECTION A
- LED Screen
- Multifunction Button/Knob (MFB/I
- Microphone
- Channel Button
- 12V Plug
- 5V, 2.4A USB-C Charging Port
- 5V, 1A USB-A Charging Port
SECTION B
Power Up & Bluetooth Pairing
- Plug the BTFREQ into your car’s 12V power socket.
- Enter the Bluetooth settings in your mobile device and enable the Bluetooth function. From the list of available accessories, find and select the ‘Scosche BTFM8°.
- Your phone will confirm once it is connected. Once connected, ensure your device is set to maximum volume.
SECTION C
Connecting to your Car’s Stereo
Find a weak station on your FM radio that has no active broadcast signal.
Press the “CH” button (1), then turn the Multi-Function Button/Knob left or
right (2) to tune the BIFREQ to match the frequency of your FM radio.
If you experience interference you may have entered an area where there is an
active broadcast signal on the station you are tuned to. Repeat the above
steps to find a different clear station.
Note: Press “CH” button to change frequencies on BIFREQ (1).
SECTION D
Reconnect to your Device
Transmitter Off: Once paired, the transmitter will automatically reconnect
when powered on.
Transmitter On: Reconnect – Tap Multi-Function Button (MFB) once ()
Note: Only tap MFB if the transmitter does not automatically reconnect.
SECTION E
Streaming Music
Stream music using the music player on your phone. You can use the controls on
the BIFREQ to control the music settings:
Play/Pause – Tap the MFB/K once
Track Forward – Turn MFB/K to the right
Track Back – Turn MFB/K to the left
Volume Up – Turn and hold MFB/K to the right
Volume Down – Turn and hold MFB/K to the left
SECTION F
Making a Call
Use your mobile phone to make a call as you normally would. Phone call audio
will automatically
stream through the BIFREQ.
Hang Up – Tap the MFB/K once
Redial last number called – Double tap MFB/K
SECTION G
Receiving a Call Phone call will come in through the BTFREO. Press MFB/K once
to answer the call Press MFB/K once to end the call Press and hold MFBIK to
reject the call
SECTION H
Voice Assistant Activation Press and hold the Multi-function button for 3
seconds to activate your smartphone’s voice assistant.
Dual-Port USB Charger
Your BTFREQ includes (1) USB-C port and (1) USB-A port to charge your devices
while driving. Simply connect using a cable suitable for your device (not
included).
SPECIFICATIONS
Input Power: 12-24V 3A
Bluetooth v5.0, Class II, up to 33 ft. (10m)
Bluetooth Profiles: HIP, A2DP
FM Transmitter Frequency Range: 87.5 – 107.9MHz (200 KHz steps)
USB-C Output: 5V 2.4A
USB-A Output: 5V ****2.4A
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Please note that
changes or modifications to this product not expressly approved by the party
responsible for compliance could void the users authority to operate the
equipment. This equipment has been tested and found to comply with the limits
fora Class B digital device, pursuant to part 15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: – Reorient or relocate the receiving antenna. –
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV
technician for help.
Canadian Compliance Statement
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions: (1) this device may not cause
interference and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class [B) digital apparatus complies with Canadian ICES-003, RSS -Gen and
RSS-210.
Portable Device Statements
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
BTFREQ How-to Video…
Scosche Industries 1550 Pacific Avenue Oxnard, California 93033
Phone: 800.363-4490 x1 / 805.486.4450 x1
www.scosche.com
©2023 Scosche Industries
Scosche & BTFREQ are trademarks of Soasche Industries. Other marks or brands
are the property of their respective owners.
Devices and or appearance may vary.
Designed in Oxnard, California
Si 01144 5123
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>