SUSSEX CBM Calibre Basin Mixer Installation Guide

SUSSEX CBM Calibre Basin Mixer

Product Information

The Voda Basin Mixer is a tapware product designed for use in bathrooms or kitchens. It comes with various options including an optional Base Flange, Hose Extension, and different outlet sizes.

• Product Code: CBM
• Product Variants:
  • VBM – Basin mixer with 90mm outlet
  • VEBM – Extended basin mixer with 90mm outlet
  • VEBM120 – Extended basin mixer with 120mm outlet
  • VMBM – Medium basin mixer with 90mm outlet
  • VMBM120 – Medium basin mixer with 120mm outlet
  • VBMSS – Basin mixer made of 316 S/S material
• Water Rating: 7.5 litres per minute (Water efficient)
• Manufacturer: Sussex Taps Pty Ltd
• Compliance: AS/NZS 3718:2005 LIC. 20081

Product Usage Instructions

Installation Guidelines

1. Ensure the mounting surface hole is completely water-tight.
2. Connect the Hot and Cold Flexible hoses to the corresponding 1/2BSP water feed lines.
3. The 1/2 connection of the Flexible hoses have a conical seal, so make sure the mating threads are cut square and burr-free.
4. It is recommended to use isolating stop valves with all installations (not supplied).
5. Ensure all fittings and connections are water-tight.

_ Note: _If the clearance hole for mounting the Mixer exceeds 35mm, the Optional Base Flange must be used. If the mounting hole clearance exceeds 45mm, a custom-made Base Flange will be required.

Plumber’s Note

• Conduct on-site testing using higher water pressures with the Mixer in the closed position (STATIC TEST).
• Do not open the Mixer when exceeding the maximum stated water pressure.
• After testing, do not relieve any high water pressure by operating the Mixer.
• Exposing the internals of the Mixer Cartridge to higher than specified water pressures will void the manufacturer’s warranty.

Additional Information

• Tapware should be installed by a Licensed Plumber following AS/NZS 3500:2003 guidelines.
• Recommended working water pressure: 300-500 kpa
• Maximum water temperature: 65 deg.c

For more information

• Visit www.sussextaps.com.au or check the water rating at www.waterrating.gov.au

Product code

• VBM: Basin mixer
• VEBM: Extended basin mixer 90mm outlet
• VEBM120: Extended basin mixer 120mm outlet
• VMBM: Medium basin mixer 90mm outlet
• VMBM120: Medium basin mixer 120mm
• VBMSS: Basin mixer 316 S/S

Installation guidelines

• The Mixer is supplied assembled, only the Fixing nut and the Brass Clamp need to be removed.
• Decide if the Optional Base Flange is to be used.
• If using the Optional Base Flange discard the smaller Base O Ring.
• Add the base Flange to base of Mixer and attach the Flexible Hoses to the Mixer Hose extensions.
• In some cases the Flexible Hoses may need to be fed through from under the mounting surface and then attach.
• Once the Flexible Hoses have been secured, lower the Mixer onto the mounting surface.
• Working from underneath the mounting surface fit Clamp and Fixing Nut.
• Before fully securing the Mixer ensure that the Base O Ring is intact and the Mixer is centered over the mounting surface hole.
• The Mixer mounting surface must be completely water-tight.
• Connect the Hot and Cold Flexible hoses to the corresponding 1/2”BSP water feed lines.
• The 1/2” connection of the Flexible hoses have a conical seal, ensure the mating threads are cut square and burr free.
• Isolating stop valves are recommended with all installations (not supplied).
• Ensure all fittings and connections are water-tight.

Note

• Optional Base Flange must be used when the clearance hole for mounting the Mixer exceeds 35mm.
• If the mounting hole clearance exceeds 45 mm a custom made Base flange will be required.

Plumber note

• On-site testing using higher water pressures must be conducted with the Mixer in the closed position. (STATIC TEST)
• Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
• At the completion of testing, do not relieve any high water pressure by operating the Mixer.
• Exposing the internals of the Mixer Car tridge to higher than specified water pressures will void the manufacturers warranty.

Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.

• sussextaps.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>