Marshall 972MOTIFNC Motif ANC True Wireless Earbuds User Manual

Marshall 972MOTIFNC Motif ANC True Wireless Earbuds

Product Information

The MOTIF A.N.C. earbuds are true wireless earbuds designed for a comfortable and immersive audio experience. The earbuds feature touch controls for easy operation and come with a charging case that can be charged using a wireless charger or a USB power source. The LED indicator on the case provides information about the charging status. The earbuds also have noise-control capabilities and can be paired with up to three devices. Additionally, the earbuds can be reset if they become unresponsive or erratic.

Product Usage Instructions

Getting Started

1. Complete the setup of the MOTIF A.N.C. earbuds.

Charging the Earbuds

To charge the earbuds:

1. Put the earbuds back in the case.
2. Close the lid of the case to turn off the earbuds and begin charging.

Charging the Case

To charge the case:

• Option 1: Use a wireless charger. Follow these steps:

1. Place the charging case with its back flat against the wireless charging pad.
2. Ensure that the front LED lights up to indicate that the case is charging.
3. Wait until the LED light turns steady green, indicating that the case is fully charged.

• Option 2: Plug the case into a USB power source.

LED Indicator
The LED indicator on the case provides information about the charging status. A steady green light indicates that the case is fully charged.

Noise Control
The MOTIF A.N.C. earbuds have noise-control capabilities to enhance your audio experience.

Pairing a New Device

To pair a new device:

1. Place the earbuds in the case and keep the lid open.
2. Press and hold the button on the case until the LED turns to a slow blue pulse.
3. Select “MOTIF A.N.C.” from your sound device’s Bluetooth list.
4. Note: Make sure to disconnect from the current device before reconnecting with a different device.

Resetting the Earbuds
If the earbuds become erratic or unresponsive:

1. Place the earbuds in the case and close the lid to restart the earbuds.
2. If the problem persists, perform a hardware reset:
3. Place the earbuds in the case and keep the lid open.
4. Press and hold the touch surface on both earbuds for 4 seconds to reset the earbuds.
5. If the problem still persists, perform a factory reset. Note: This will delete all user settings, and the earbuds will need to be set up again.
6. Place the earbuds in the case and keep the lid open.
7. Press and hold the button on the case for 10 seconds until the LED turns purple to reset the earbuds to factory settings.
8. Remove “MOTIF A.N.C.” from your sound device’s Bluetooth list before pairing again.

Cleaning Your MOTIF A.N.C.
Follow the provided instructions to clean your MOTIF A.N.C. earbuds properly.

Important Safety Instructions
Ensure to follow the important safety instructions provided in the user manual to prevent any potential harm or damage caused by improper usage or disposal of the product.

Overview

GETTING STARTED

1. Open the charging case.
2. Press and hold the button on the case until the LED turns to a slow blue pulse.
3. Select MOTIF A.N.C. from your sound device’s Bluetooth® list.
4. Download the Marshall Bluetooth app and follow the in-app instructions to complete the setup.

TOUCH CONTROLS

Touch the left or right earbud to control your music, phone calls, and more. The long touch behavior can be customized in the app.

• 1 touch to play/pause or receive/end a call
• 2 touches to skip forward or reject a call
• 3 touches to skip backward
• Long touch to toggle noise canceling, transparency, and ANC off

CHARGING THE EARBUDS

Put your earbuds back in the case and close the lid to turn them off and begin charging.

CHARGING THE CASE
Use a wireless charger or plug the case into a USB power source to charge it. The case is fully charged when the front-facing LED is steady green.

To charge the case using a wireless charger, follow the instructions below.

1. Place the charging case with its back flat against the wireless charging pad.
2. Make sure that the front LED lights up to indicate that the case is charging.
3. Once the LED light has turned steady green the case is fully charged.

LED INDICATOR

The LED shows the case battery charge, from red through yellow to green (0–100%). It pulses blue while in Bluetooth pairing mode.

NOISE CONTROL

Long touch either earbud to cycle through the noise control modes.

• Noise-canceling mode – blocks out your surroundings and lets you focus on the music
• Transparency mode – allows you to hear your surroundings and hold conversations without removing your earbuds
• Off–noise control is turned off

The amount of noise canceling and transparency can be adjusted in the Marshall Bluetooth app.

PAIRING A NEW DEVICE

Motif A.N.C. remembers up to 3 previously paired devices and will try to reconnect with the last connected device.

1. Place the earbuds in the case and keep the lid open.
2. Press and hold the button on the case until the LED turns to a slow blue pulse.
3. Select MOTIF A.N.C. from your sound device’s Bluetooth list.

Note:
Motif A.N.C. can be connected with one sound device at a time. Make sure to disconnect from the current device before reconnecting with a different device.

RESETTING THE EARBUDS

If your earbuds become erratic or unresponsive, follow the instructions below.

1. Place the earbuds in the case and close the lid to restart the earbuds.

If the problem persists, perform a hardware reset:

1. Place the earbuds in the case and keep the lid open.
2. Press and hold the touch surface on both earbuds for 4 seconds to reset the earbuds.

If the problem persists, perform a factory reset.

Note: This will delete all user settings and the earbuds will need to be set up again.

1. Place the earbuds in the case and keep the lid open.
2. Press and hold the button on the case for 10 seconds, until the LED turns purple, to reset the earbuds to factory settings.
3. Remove MOTIF A.N.C. from your sound device’s Bluetooth list before pairing again.

CLEANING YOUR MOTIF A.N.C.

Earbuds come in close contact with your skin often and sometimes for long periods of time. This will over time cause build-up of dirt and grease that can affect performance and may cause skin irritation. Clean your earbuds regularly to keep them fresh and make them last longer.

Unplug any cables before cleaning the case. Make sure everything is completely dry before using the earbuds, putting the earbuds back in the case, or plugging in a USB charger.

Remove the silicone ear tips from the earbuds and clean them separately. Use a disinfectant wipe or a lint-free cloth, slightly damp with 70% isopropyl alcohol or 75% ethyl alcohol to gently clean the ear tips, the exterior surfaces of the earbuds, and the case. Avoid getting moisture in any openings or in the speaker mesh. Carefully clean those areas with a dry and soft brush or a cotton swab.

• Do not use any sharp objects.
• Do not use compressed air.
• Do not use products containing bleach or hydrogen peroxide.
• Do not submerge the earbuds in any cleaning agents.

Marshall is a trademark of Marshall Amplification Plc. Permission granted. The design of the product and packaging are intellectual properties of Zound Industries International AB, Centralplan 15 111 20 Stockholm, Sweden. © Zound Industries International AB. All Rights Reserved.

The Bluetooth® wordmark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Zound Industries International AB is under license.

IMPORTANT SAFETY INSTRUCTIONS

• Not suitable for children under age three. Contains small parts, which may be a choking hazard.
• Long-term exposure to loud music or sounds may cause hearing loss. To prevent possible hearing damage, do not listen at high volume levels for long periods.
• Electrical products. cables, batteries. packaging, and the manual, should not be mixed with general household waste. For proper recycling, please take these products to a designated collection point where they will be accepted free of charge or return them to your local retailer. Correct product disposal saves resources and prevents negative effects on human health and the environment.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, dispose of defective rechargeable batteries at special collection points or return them to your specialist dealer.

WARNINGS

• Set your sound source to low volume before using the headphones.
• Do not use these headphones when operating a motor vehicle, a bicycle, or machinery or where your inability to hear outside sounds may present a danger to you or others.
• Using these headphones limits your ability to hear noises around you, regardless of listening volume.
• Keep away from fire, water, and high-voltage equipment. Do not modify, disassemble, open, drop, crush, puncture, or shred these headphones. Do not heat above 113°F (45 °C).
• Do not short-circuit the internal battery or its cells.
• In the event of cell leakage, do not allow the liquid to come In contact with the skin or the eyes.
• The internal battery is not end-user replaceable.
• Only use the included charging case with the Motif A.N.C. earbuds.

DISCLAIMER

• Stated play time is calculated using a random selection of music, played at medium volume.
• The information contained herein is correct at the time of publication, with reservation for editorial errors. This product is software dependent and its functions and compatibility can change when updating the software.
• Hereby, Zound Industries International AB, declares that this product is in compliance with 2014/53/EU and the UK Radio Equipment Regulations 2017 (S12017/1206).

Maximum RF transmit power:
Bluetooth (2402-2480 MHz) < 20 dBm

The full text of the EU and UKCA declaration of conformity is available at the following website:
www.marshallheadphones.com/doc.

UK Authorised Representative:
Zound Industries UK LTD, 24 Old Queen Street, London, SW1H 9HP, United Kingdom Designed in Stockholm Produced in China.

LEGAL NOTICE

Design of de11ice and packaging are intellectual properties of Zound Indulges International AB C> All Rights Reserved. MARSHALL, Marshall Amps, their respecti11e logos. “Marshall” and “Marshall” trade dress are trademarks and intellectual property of Marshall Amplification Pie and may not be used without permission Permission granted to Zound Industries International AB.

• The Bluetooth® wordmark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Zound Industries Is under license.
• All other trademarks are the property of their respective owners and may not be used without permission.
• For more legal information related to this product and to its use in your specific region, and for more detailed information about Zound Industries and partner & license information, please 11is1t the website: www.marshallheadphones.com. The user Is recommended to 11isit the website regularly for up-to-date information.

Zound Industries International AB. Centralplan 15, 111 20 Stockholm, Sweden.

FCC STATEMENT

WARNING:
Any changes or modifications to this device not expressly approved by the party responsible for compliance could 11oid the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules Operation Is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This device must not be located or operated In conjunction with any other antenna or transmitter.

This equipment has been tested and found to comply with the hm1ts for a Class B d1g1tal device, pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and. 1f not installed and used In accordance with the instructions. may cause harmful interference to radio communications Howe11er, there is no guarantee that interference will not occur In a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver Is connected.
• Consult the dealer or an experienced radio/TV technician for help.

U.S responsible party, contact information

Zound Industries USA, Inc
260 W 39th Street Suite 1101, New York, NY 10018. USA
Telephone number. 646-214-1003.

IC STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subJect to the following two conditions· (1) this device may not cause interference. and (2) this device must accept any interference, including interference that may cause undesired operation of the dev,ce.

This Class B digital device complies with Canadian ICES-003.

References

• Anatel — Agência Nacional de Telecomunicações
• Marshall — 60 years of loud | Marshall.com
• Marshall.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>