Marshall Emberton II Bluetooth Speaker Instruction Manual

May 15, 2024
Marshall

EMBERTON II – FULL ONLINE MANUAL

DEVICE LAYOUT

Marshall Emberton II Bluetooth Speaker - cover Marshall Emberton II Bluetooth Speaker - icon 1

GENERAL

  1. BLUETOOTH BUTTON
    Push and hold the Bluetooth® button until the LED turns to a slow red pulse to start pairing mode

  2. CONTROL KNOB
    I Push and hold for 2 seconds to turn on/off
    II Push once to play/pause
    III Push right/left to skip forward/back
    IV Hold right/left to fast forward/rewind
    V Hold upwards/downwards to adjust the volume

  3. BATTERY INDICATOR
    The 10 segment Battery indicator shows the battery charge with a steady light and a rising animation indicates charging

  4. USB-C POWER INPUT
    Charge the speaker by plugging it into a USB power source

INSTRUCTIONS

BLUETOOTH PAIRING
I Push and hold the control knob until the speaker turns on
II Push and hold the Bluetooth button until the LED turns to a slow red pulse
III Select EMBERTON II from your audio device’s Bluetooth list

PERFORMING A FACTORY RESET
A factory reset will reset the speaker to its original settings, excluding any firmware updates
Note: This will delete all user settings and the speaker will need to be set up again
I Ensure that the speaker is on
II Push and hold the Bluetooth button for 7 seconds All indicators turn off and the speaker restarts
III Remove EMBERTON II from your audio device’s Bluetooth list before pairing again

MARSHALL BLUETOOTH APP
Download the Marshall Bluetooth app to get the most out of your speaker and keep it up to date with the latest software

CLEANING THE SPEAKER
Clean your speaker regularly to keep it fresh and last longer.
Unplug any leads before cleaning the speaker and make sure everything is completely dry before plugging in any USB power source.
The silicone sleeve can be removed and cleaned separately Use a disinfectant wipe or a lint-free cloth, slightly damp with 70% isopropyl alcohol or 75% ethyl alcohol to gently clean silicon parts Dry them with a towel before putting them back on the speaker.
Carefully clean the speaker mesh and openings with a dry and soft brush, or a cotton swab

  • Do not use any sharp or metal objects
  • Do not use compressed air
  • Do not use products containing bleach or hydrogen peroxide
  • Do not submerge the speaker in any cleaning agents

BATTERY CARE GUIDE
Your speaker comes equipped with a high-performance lithium-ion battery and the life span is affected by charging and usage Follow the guidelines below to keep your battery in great condition for as long as possible

  • Avoid using fast chargers if possible Fast charging causes stress on the battery and will degrade it
  • Avoid charging the battery when it is already full or letting it drain completely Try keeping the charge between 30% and 80%
  • If the speaker is stored for a long time, do so with a half-charged battery and in a cool, dark, and dry place
  • Do not use or charge the speaker in hot and unventilated places, 45°C/113°F and above, such as in a parked car or by a window in direct sunlight
  • Avoid charging the battery at low temperatures, below 10°C/50°F and using the speaker below 0°C/32°F
  • Avoid strong mechanical shocks such as dropping the speaker on hard surfaces as it might damage the battery

STACK MODE

Connect two or more Emberton II speakers in a Stack session for a bigger sound Play anything on the main speaker and all speakers in the session will play in sync You can adjust the volume on any individual speaker for the perfect balance.

  1. MAIN SPEAKER
    Triple press the Bluetooth button to start or end a Stack session. The LED starts to blink until any other speaker joins the session.

  2. ADDITIONAL SPEAKER
    Double press the Bluetooth button on any speaker you want to add to the session The LED starts to blink until the speaker has joined a session While in a session, the speaker will disconnect from any previously connected audio device and will try to reconnect after leaving the session.
    To remove a speaker from the session, double press the Bluetooth button on that speaker.

Marshall Emberton II Bluetooth Speaker - icon 3

TROUBLESHOOTING

PROBLEM CAUSE ACTION
The speaker does not turn on The battery has no charge Plug the speaker into

a USB power source
to charge it
Cannot connect or pair with a Bluetooth device| Bluetooth is not enabled on your device (phone
or computer)| Activate Bluetooth on your audio device
The speaker is not turned on| Push and hold the control knob for 2 seconds to turn on the speaker before setting it in pairing mode
Cannot play in Stack mode| The playback device is not connected to the main speaker| Make sure that your playback device (phone or computer) is paired with the main speaker
Bluetooth connection drops out| The Bluetooth devices are too far apart, or the
connection is affected due to obstacles| Move the devices closer to each other so that they are unobstructed by obstacles such as walls or doors
Bluetooth connection drops out| There is a strong electric field surrounding the
speaker  Items such as microwave ovens, wireless
network adapters, fluorescent lights and gas cookers use the same frequency range as the
Bluetooth device  This may lead to electrical disturbances| Move the speaker to another spot or turn off or move the interfering electronic device
Erratic behaviour| The speaker is not using the latest firmware version| Download the Marshall Bluetooth app and connect to the speaker Follow the in- app
instructions to ensure that the speaker has the latest firmware version
There is a software error| Perform a factory reset by pressing the Bluetooth button for 7 seconds The speaker needs to be set up again

◄ BACK TO INDEX ►

Documents / Resources

| Marshall Emberton II Bluetooth Speaker [pdf] Instruction Manual
Emberton II, Emberton II Bluetooth Speaker, Bluetooth Speaker, Speaker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals