Ruijie RG-RAP2266 Wifi 6 Ceiling Room Hotspot Installation Guide

Ruijie RG-RAP2266 Wifi 6 Ceiling Room Hotspot

Product Information

The Ruijie Reyee RG-RAP2266 Access Point is a high-performance wireless access point designed for network deployment and management. It provides reliable and secure wireless connectivity for various applications.

Key Features

• High-speed wireless connectivity
• Advanced security features
• Easy installation and configuration
• Support for multiple wireless standards
• Robust performance and coverage

Specifications

• Model: Ruijie Reyee RG-RAP2266
• Wireless Standards: IEEE 802.11a/b/g/n/ac
• Frequency Band: 2.4 GHz and 5 GHz
• Data Transfer Rate: Up to 1733 Mbps
• Antenna: Internal high-gain antennas
• Security: WPA/WPA2-PSK, WPA/WPA2-Enterprise, MAC filtering
• Power Supply: PoE (Power over Ethernet) or external power adapter
• Dimensions: 200mm x 200mm x 40mm

Package Contents

• Ruijie Reyee RG-RAP2266 Access Point
• Power adapter
• Ethernet cable
• Mounting kit
• User manual

Product Usage Instructions

Hardware Installation

1. Choose a suitable location to install the access point, ensuring it is within the coverage area and has access to power.
2. Mount the access point on the wall or ceiling using the provided mounting kit.
3. Connect one end of the Ethernet cable to the LAN port of the access point and the other end to a network switch or router.
4. Power on the access point using either PoE or the provided power adapter.

Configuration

1. Ensure that your computer or mobile device is connected to the same network as the access point.
2. Open a web browser and enter the IP address of the access point (usually provided in the user manual) to access the configuration interface.
3. Follow the on-screen instructions to configure the wireless settings, including SSID, security options, and network mode.
4. Save the settings and restart the access point for the changes to take effect.

Network Management

Once the access point is configured and running, you can use the following methods to manage and monitor your network:

• Access the Ruijie Reyee official website or technical support website for product updates, downloads, and documentation.
• Visit the case portal or community platform for technical support and troubleshooting assistance.
• Contact Ruijie Networks’ technical support team via email for further assistance.

Please refer to the user manual for detailed instructions on advanced configurations, troubleshooting, and additional features.

Audience

This document is intended for:

• Network engineers
• Technical support and servicing engineers
• Network administrators

Technical Support

• O fficial Website of Ruijie Reyee: https://www.ruijienetworks.com/products/reyee.
• Technical Support Website: https://www.ruijienetworks.com/support.
• Case Portal: https://caseportal.ruijienetworks.com.
• Community: https://community.ruijienetworks.com.
• Technical Support Email: service_rj@ruijienetworks.com.

Conventions

1. GUI Symbols

Signs
The signs used in this document are described as follows:
Danger
An alert that calls attention to safety instructions that if not understood or followed can result in personal injury.
Warning
An alert that calls attention to important rules and information that if not understood or followed can result in data loss or equipment damage.
Caution
An alert that calls attention to essential information that if not understood or followed can result in function failure or performance degradation.

Note
An alert that contains additional or supplementary information that if not understood or followed will not lead to serious consequences.

Specification

An alert that contains a description of product or version support.
Note
This manual provides installation steps, troubleshooting, technical specifications, and usage guidelines for cables and connectors. It is intended for users who want to understand the above and have extensive experience in network deployment and management and assume that users are familiar with related terms and concepts.

Product Overview

About the RG RAP2266 Access Point
The RG RAP2266 is a high-performance ceiling mount dual radio Wi-Fi access point designed to cover a large and medium-sized indoor area The access point adopts either IEEE 802.3 at PoE power supply or 12 V DC 2 A local power supply. Compliant with the IEEE 802.11a/b/g/n/ac Wave1/Wave2/ax standard, the access point can work in both 2.4 GHz and 5 GHz frequency bands and supports dual stream MU MIMO. The access point delivers s a combined data rate of 2976 Mbps, with up to 574 Mbps in the 2.4 GHz band and 2 402 Mbps in the 5 GHz band. With built in omnidirectional antennas and a Wi-Fi coverage radius of 40 m (131.23 ft.) ft.), the access point can be deployed in various scenarios covering offices , business, villa s, hotels, and government

Package Contents

Table 1-1 Package Contents

Note
The package contents generally contain the above items. The actual delivery is subject to the order contract. And please check your goods carefully against the order contract. If you have any questions, please contact the distributor.

Hardware Features

Top Panel
Figure 1-1 Top Panel of an RG RAP2266 Access Point

Note
The C MIIT ID is printed on the product nameplate

Table 1-2 L ED

Flashing twice in succession

| Possible cases:

Restoring the access point to factory settings. Upgrading the firmware.

Note: Do not power off the access point in this case.

One long flash followed by three short flashes| ****

A fault occurs.

Bottom Panel
Figure 1-2 Bottom Panel of a RG RAP2266 Access Point

Table 1-3 Ports and Reset Hole

1

| ****

Reset Hole

| Stick the pin into the Reset hole: Restart the access point.
Press and hold the pin to the Reset hole for more than 5 seconds: Restore the access point to factory settings.
2| LAN/PoE Port| 10/100/1000Base-T Ethernet port, supporting PoE input
3| DC Connector| 12 V DC/2 A power supply

Technical Specifications

Table 1-4 Technical Specifications

802.11a/b/g/n

Operating Radio

| 802.11b/g/n/ax: 2.4 GHz to 2.4835 GHz

802.11a/n/ac/ax: 5.150 GHz to 5.350 GHz, 5.470 GHz to 5.725 GHz, and 5.725 GHz to 5.850 GHz

Antenna

| Built-in omnidirectional antennas (2.4 GHz: 3.53 dBi, 5 GHz: 5.15 dBi)

Note

The peak gain mentioned above refers to the gain of a single antenna.

Spatial Streams| 2.4 GHz: two spatial streams, 2×2 MIMO

5 GHz: two spatial streams, 3×3 MIMO

Max. Data Rate| 2.4 GHz: 574 Mbps
| 5 GHz: 2402 Mbps

Combined: 2976 Mbps

---|---
Modulation| OFDM: BPSK@6/9 Mbps, QPSK@12/18 Mbps, 16QAM@24 Mbps, and 64QAM@48/54 Mbps

DSSS: DBPSK@1 Mbps, DQPSK@2 Mbps, and CCK@5.5/11 Mbps MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM, 256QAM, and 1024QAM

OFDMA

Receive Sensitivity| 11b: –91 dBm (1 Mbps), –90 dBm (5.5 Mbps), –87 dBm (11 Mbps)

11a/g: –89 dBm (6 Mbps), –82 dBm(24 Mbps), –78 dBm (36 Mbps), –72 dBm

( 54 Mbps)

11n: –85 dBm (MCS0), –67 dBm (MCS7), –62 dBm (MCS8)

11ac: 20 MHz: –85 dBm (MCS0), –62 dBm (MCS8)

11ac: 40 MHz: –82 dBm (MCS0), –59 dBm (MCS8)

11ac: 80 MHz: –79 dBm (MCS0), –53 dBm (MCS9)

11ac: 160 MHz: –76 dBm (MCS0), –50 dBm (MCS9)

11ax: 20 MHz: –85 dBm (MCS0), –62 dBm (MCS8), –58 dBm (MCS11)

11ax: 40 MHz: –82 dBm (MCS0), –59 dBm (MCS8), –54 dBm (MCS11)

11ax: 80 MHz: –79 dBm (MCS0), –53 dBm (MCS9), –52 dBm (MCS11)

11ax: 160 MHz: –76 dBm (MCS0), –49 dBm (MCS11)

Max. Transmit Power

| 2.4 GHz ≤ 20 dBm 5 GHz ≤ 30 dBm

Note

The transmitted power may vary based on local laws and regulations.

Power Adjustment| Configurable in increments of 1 dBm
Dimensions

(W x D x H)

| 220 mm x 220 mm x 52.6 mm (8.66 in. x 8.66 in. x 2.07 in., without the mounting bracket)
Weight| ≤ 0.5 kg (1.10 lbs, without the mounting bracket)
Service Port| One 10/100/1000/1000Base-T Ethernet port, supporting PoE input
Management Port| N/A
Status LED| One LED (Blue)
Power Supply| There are two power supply modes available:

PoE+ power supply: IEEE 802.3at-compliant Local power supply: 12 V DC /2 A

| Note: The power adapter is an optional accessory (inner diameter: 2.1 mm/0.08 in., outer diameter: 5.5 mm/0.22 in., and depth: 9 mm/0.35 in.).
---|---
Max. Power Consumption| 18 W

Temperature

| Operating temperature: 0°C to 40°C (32°F to 104°F)
Storage temperature: –40°C to +70°C (–40°F to +158°F)

Humidity

| Operating humidity: 5% to 95% RH (non-condensing)
Storage humidity: 5% to 95% RH (non-condensing)
Certification| CE
MTBF| > 400,000 hours

Power Specifications
The access point can be powered by either PoE or DC power supply
Caution

• If the access point adopts DC power supply, a Ru i jie certificated 12 V DC/2A power adapter is required. The DC adapter needs to be purchased separately
• If the access point adopts PoE power supply, connect the LAN/PoE port of the access point to a PoE capable port of a switc h or power sourcing equipment (PSE). Make sure that the PSE is 802.3at capable

Cooling Solutio n
The access point a dopts a fanless design.
Caution
Maintain a sufficient clearance around the access point for air circulation.

Preparing for Installation

Safety Precautions
Note

• To prevent device damage and physical injury, please read the safety recommendations carefully as described in this chapter.
• Recommendations do not cover all possible hazardous situations.

General Safety Precautions

• Do not expose the AP to high temperature, dust, or harmful gases.
• Do not install the AP in an area prone to fire or explosions.
• Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.
• Do not subject the AP to unstable voltage, vibration, and noises.
• The installation site should be dry. Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.
• The installation site should be free from water including possible flooding, seepage, dripping, or condensation. The installation site should be selected according to network planning and communications equipment feature s, and considerations such as climate, hydrology, geology, earthquake, electrical power, and transportation.

Handling Safety

• Do not move the access point frequently.
• Turn off all power supplies and unplug all power cables before you remove the device.

Electric Safety

Warning

• Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus causing severe even fatal damages to humans and devices.
• Direct or indirect contact with a wet object (or your finger) on the high voltage and power line can be fatal.
• Please observe local regulations and specifications when performing electrical operations. Relevant operators must be qualified.
• Carefully check for any potential hazards in the working area such as damp/wet ground or floors.
• Find the location of the emergency power supply switch in the room before installation. Cut off the power supply first in case of an accident.
• Be sure to make a careful check before shutting down the power supply.
• Do not place the devi ce in a damp/wet location. Do not let any liquid enter the chassis
• Keep the AP far away from grounding or lightning protection devices for power equipment.
• Keep the AP away from radio stations, radar stations, high frequency high current devices, and mi crowave ovens.
• Installation Environment Requirements
• The AP must be installed indoors. To ensure normal operation, the installation site must meet the following requirements.

Installation Requirements

• Install the AP in a well ventilated environment. If it is installed in a closed room, make sure there is a good cooling system.
• Make sure the site is sturdy enough to support the RG RAP2266 and its accessories.
• Make sure the site has enough space for installing the RG RAP2266 and leave sufficient room around the AP for ventilation.

Ventilation Requirements

• The access point adopts natural cooling. Reserve a sufficient clearance around the access point to ensure proper ventilation.

Temperature/Humidity Requirements

• To ensure normal operation and equipment service life, maintain appropriate temperature and humidity levels in the equipment room. Improper room temperature and humidity can cause damage to the device.
• High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage. Sometimes it may lead to changes in the mechanical properties of materials and corrosion of metal parts.
• Low relative humidity can dry and shrink insulation sheets and cause static electricity that can damage the circuitry.
• High temperatures greatly reduce device reliability and shorten service life.

Cleanliness Requirements

Dust poses a serious threat to device operation. Dust on the surface of the device can be absorbed onto metal contact points by static electricity causing poor contact. Electrostatic absorption of dust occurs more easily when the relative humidity is low, and might shorten the equipment service life and cause communication failures. The following table shows the maximum concentration and diameter of dust allowed in the equipment room.

1.4 × 107

|

7 × 105

|

2.4 × 105

|

1.3 × 105

The amount of salt, acids, and sulfides in the air are also strictly limited for the equipment room. These substances can accelerate metal corrosion and aging of some parts. The following table describes the limits of some hazardous gases such as sulfur dio xide , hydrogen sulfide, nitrogen dioxide, ammonia gas and chlorine gas in the equipment room.

Note
Average refers to the average value of harmful gases measured in one week. Maximum indicates the upper  limit of the harmful gas measured in one week for up to 30 minutes every day

Power Supply Requirements
DC power adapter: 12 V DC/2A. The technical specifications of the DC connector are as follows:

Inner Diameter

|

Outer Diameter

|

Depth

|

Conductor Resistance

|

Voltage Resistance

| Voltage for Insulator and Conductor Test)|

Polarity Symbol

---|---|---|---|---|---|---

2.10 ± 0.05

mm

(0.83 in. ±

0.002 in.)

|

5.50 ± 0.05

mm

(0.22 in. ±

0.002 in.)

|

9 mm

(0.35

in.)

|

5 Ω

|

100 MΩ

|

1000 V

| Center (tip) of the output plug: Positive (+)

Barrel (ring) of the output plug: Negative (-)

Reverse polarity symbol is not allowed.

• PoE injector: IEEE 802.3at compliant

Caution

• The DC input power should be greater than the power actually consumed by the access point
• You are advised to use a DC power adapter with the specifications recommended by Ruijie .
• You are advised to use a Ruijie-certified PoE injector.

Anti-interference Requirements

• Keep the access point as far away from the lightning prevention equipment and grounding equipment of the power device as possible.
• Keep the access point far away from radio stations, radar stations, high frequency high current devices, and microwave ovens.

Tools

Table 2-1 Tool

Common Tools

| Phillips screwdrivers, power cords, Ethernet cables, cage nuts, diagonal pliers, and binding straps
---|---

Special Tools

| Antistatic gloves, wire stripper, crimping pliers, crystal connector crimping pliers, and wire cutter
Meter| Multimeter
Relevant Devices| PC, display, and keyboard

Note
The RG RAP2266 is delivered without a tool kit. The tool kit is customer supplied..

Installing the Access Point

The RG RAP2266 access point must be installed and used indoors.
Caution
Before installing the access point, make sure you have carefully read the requirements described in Chapter 2.

Before You Begin
Carefully plan and arrange the installation position, networking mode, power supply, and cabling before installation. Confirm the following requirements before installation:

• The installation site provides sufficient space for proper ventilation.
• The installation site meets the temperature and humidity requirements of the access point.
• The power supply and required current are available at the installation site.
• The selected power supply modules meet the system power requirements.
• The installation site meets the cabling requirements of the access point.
• The installation site meets the site requirements of the access point.
• The customized access point meets the client-specific requirements.

Precautions for Installation
To avoid damage to the access point , observe the following safety

• Do not power on the access point during installation.
• Install the access point in a well ventilated location.
• Do not expose the access point to high temperature.
• Keep the access point away from high voltage cables.
• Install the access point in indoor scenarios.
• Do not expose the access point to thunderstorm or strong electric field.
• Keep the access point clean and dust free.
• Cut off the power switch before cleaning the access point.
• Do not wipe the device with a damp cloth.
• Do not wash the device with liquid.
• Do not open the enclosure when the access point is working.
• Secure the access point properly

Installing t he Access Poin t
Caution

• You are advised to install the access point where you can get the optimal Wi Fi coverage. In indoor scenarios, the Wi Fi coverage of a ceiling mount access point is larger than that of a wall mount access point. You are advised to i nstall the access point on the ceiling

• Image is for indicative purpose only and may not represent exact equipment

  • Take out the mounting bracket from the packaging material and use the mounting bracket as a template to mark the mounting holes’ positions. Drill two holes at 80 mm (3.15 in) spacing on the wall or ceiling.
    Figure 3-1 Drilling Two Holes on the Wall or Ceiling

  • S ecure the mounting bracket to the ceiling or wall by using self tapping screws .
    Figure 3-2 Securing the Mounting Bracket to the Wall or Ceiling

  • Connect the Ethernet cable to the LAN /PoE port on the rear of the access point. See 7.1 C onnectors and Media for the supported wiring for twisted pairs

Caution

• A void a small bend radius at the connector of the cable.
• Y ou are advised not to use an Ethernet cable with an RJ45 boot

Figure 3-3 Connect ing the Ethernet C able to the LAN /PoE P ortAlign the round feet at the bottom of the access point over the mounting holes on the bracket. Slide the AP into the mounting bracket.

Caution

• Install the Ethernet cable properly before securing the access point to the mounting bracket.
• The access point can be installed in any of four directions on the mounting bracket depending on how you route the Ethernet cable.
• The round feet should fit easily into the mounting holes . Do not force the round feet into the mountin g holes .
• After installation, verify that the access point is secured properly .

Figure 3-4 Securing the Access Point to the Mounting Bracket

Bundling Cables

Caution

• The power cords and other cables should be bound in a visually pleasing way
• When you bundle twisted pairs or fiber optic cables, make sure that the cables at the connectors have natural bends or bends of large radius .
• Do not over tighten cable bundle as it may reduce the cable life and performance .

The steps for cable bundling are as follow s:

1. Bundle the drooping part of the cables and place the bundle as near the ports as possible
2. R oute the cables under the access point and run in straight line

Checklist After Installation

1. Checking Access Point
   • Verify that the external power supply matches with the requirement of the access point.
   • Verify that the access point is securely fastened.
2. Checking Cable Connection
   • Verify that the UTP/STP cable matches with the port type.
   • Verify that cables are properly bundled.
3. Checking Power Supply
   • Verify that the power cord is properly connected and compliant with safety requirements.
   • Verify that the access point functions properly after power on.

Removing the Access Point
Hold the access point in your hands and push it upward and away from the mounting bracket

Verifying Operating Status

Setting up Configuration Environment
If the access point is powered by PoE or DC power adapter , verify that the power cord is proper ly connected and compliant with safety requirements.
Powering on the Access Point
Check list Before Power on

• Verify that the power cord is properly connected
• Verify that the input voltage meets with the requirement of the access point

Check list After Power on

• Verify that the LED works normally
• Verify that the mobile phone or other wireless device can discover the SSID broadcast by the access point.

If multiple devices exist o n the network, use SSID @Ruijie m XXXX . If only one device exists o n the network, use SSID @Ruijie s XXXX .

Monitoring and Maintenance

Monitoring
When RG RAP2266 is operating, you can monitor its status by observing the LED. See Table 1 2 L ED for details.
Maintenance
If the hardware is faulty, please contact Ruijie technic al support for help.

Troubleshooting

General Troubleshooting Flowchart

Common Faults

• The status LED is still off after the access point is powered on.
  • If the access point is powered by PoE, verify that the power sourcing equipment (PSE) should be at least 802.3at-capable and the Ethernet cable is connected properly.
  • If the access point is powered by a DC adapter, verify that the adapter has mains input and works properly.
• The Ethernet port does not work after the Ethernet cable is plugged in.
• Check whether the peer device is working properly. Then verify that the Ethernet cable is capable of providing the required data rate and is properly connected.
• The client cannot find the access point.
  • Verify that the access point is properly powered.
  • Verify that the Ethernet port is correctly connected.
  • Verify that the access point is correctly configured.
  • Move the client to adjust the distance between the client and the access point.

Appendix

Connectors and Media 1000BASE

• T/100BASE TX/10BASE T Port 1000BASE
• T/100BASE TX/10BASE T is a 10/100/1000 Mbps port that supports auto negotiation and auto
• MDI/MDIX Crossover.
• Compliant with IEEE 802.3ab, 1000BASE
• T requires Category 6 or Category 5e 100 ohm UTP or STP (STP is recommended) with a maximum distance of 100 meters (328.08 feet). 1000BASE
• T port uses four twisted pairs for data transmission , all of which must be con nected . Twisted pairs for the 1000BASE T port are connected as shown in the following figure.

Figure 7-1 Four Twisted Pairs Connection 100BASE TX/10BASE T port can also be connected by cables of the preceding specifications. Besides, the 10BASE T port can be connected by 100 ohm Category 3, Category 4, and Category 5 cables with a maximum distance of 100 meters (328.08 feet). 100BASE TX p ort can be connected by 100 ohm Category 5 cables with a maximum distance of 100 meters (328.08 feet). The following table lists definitions of pin signals for the 100BASE TX/10BASE T port.

Table 7-1 100BASE TX/10BASE T Pin Assignments

The following figure shows feasible connections of the straight through and crossover twisted pairs for a 100BASE TX/10BASE T port.
Figure 7-2 100BASE TX/10BASE T Connection

Cablin g
During installation, route cable bundles upward or downward along the sides of the rack depending on the actual situation in the equipment room. All cable connectors used for transit should be placed at the bottom of the cabinet rather than be exposed outside of the cabinet. Power cords are routed beside the cabinet, and top cabling or bottom cabling is adopted according to the actual situation in the equipment room, such as the positions of the DC power distributi on box, AC socket, or lightning protection box.

1. Requirements for Cable Bend Radius
   • The bend radius of a fixed power cord, network cable, or flat cable should be over five times greater than their respective diameters. The bend radius of these cables that are often bent or plugged should be over seven times greater than their respective diameters.
   • The bend radius of a fixed common coaxial cable should be over seven times greater than its diameter. The bend radius of the common coaxial cable that is often be nt or plugged should be over 10 times greater than its diameter.
   • The bend radius of a fixed high speed cable (such as an SFP+ cable) should be over five times greater than its diameter. The bend radius of the fixed high speed cable that is often bent or pl ugged should be over 10 times greater than its diameter.
2. Precautions for Bundling up Cables
   • Before cables are bundled, mark labels and stick the labels to cables wherever appropriate.
   • Cables should be neatly and properly bundled in the rack without twisting or bending.

Figure 7-3 Bundling up Cables

• Cables of different types (such as power cords, signal cables, and ground ing cables) should be separated in cabling and bundling. Mixed bundling is disallowed. When they are close to eac h other, you are advised to adopt crossover cabling. In the case of parallel cabling, maintain a minimum distance of 30 mm (1.18 in.) between power cords and signal cables.
• The cable management brackets and cabling troughs inside and outside the cabinet sh ould be smooth without sharp corners.
• The metal hole traversed by cables should have a smooth and fully rounding surface or an insulated lining.
• Use cable ties to bundle up cables properly. Please do not connect two or more cable ties to bundle up cables.
• After bundling up cables with cable ties, cut off the remaining part. The cut should be smooth and trim, without sharp corners.

Figure 7-4 Bundling up Cables

When cables need to be bent, you should first bundle them up. However, the buckle cannot be bundled withi n the bend area. Otherwise, considerable stress may be generated in cables, breaking cable cores.

Figure 7-5 Bundling up Cables

• Cables not to be assembled or remaining parts of cables should be folded and placed in a proper position of the rack or cable trough. Th e proper position refers to a position that does not affect device running or damage the device or cable.
• 220 V and 48 V power cords must not be bundled on the guide rails of moving parts.
• The power cords connecting moving parts such as grounding cables should be reserved with some access after being assembled to avoid suffering tension or stress. After the moving part is installed, the remaining cable part should not touch heat sources, sharp corners, or sharp edges. If heat sources cannot be avoided, hi gh temperature cables should be used. If heat sources cannot be avoided, high temperature cables should be used.
• When screw threads are used to fasten cable terminals, the anchor or screw must be tightly fastened.

Figure 7-6 Cable Fastening

1. Flat Washer
2. Nut
3. Spring Washer
4. Flat Washer
   • Hard power cords should be fastened in the terminal connection area to prevent stress on terminal connection and cable.
   • Do not use self tapping screws to fasten terminals.
   • Power cords of the same type and in the same cabling direction should be bundled up into cable bunches, with cables in cable bunches clean and straight.
   • Binding by using buckles should be performed according to Table 7 1

Table 7-2 Cable Bunch

• No knot is allowed in cabling or bundling.
• For wiring terminal blocks (such as air switches) of the cold pressing terminal type, the metal part of the cord end terminal should not be exposed outside the terminal block when assembled.

Copyright
Copyright © 2023 Ruijie Networks All rights are reserved in this document and this statement. Without the prior written consent of Ruijie Networks, any organization or individual shall not reproduce, extract, back up, modify, or propagate the con tent of this document in any manner or in any form, or translate it into other languages or use some or all parts of the document for commercial purposes. , and other Ruijie networks logos are trademarks of Ruijie Networks. All other trademarks or registered trademarks mentioned in this document are owned by their respective owners.
Disclaimer
The products, services, or features you purchase are subject to commercial contracts and terms, and some or all of the products, services, or features descri bed in this document may not be available for you to purchase or use. Except for the agreement in the contract, Ruijie Networks makes no explicit or implicit statements or warranties with respect to the content of this document. The content of this document t will be updated from time to time due to product version upgrades or other reasons, Ruijie Networks reserves the right to modify the content of the document without any notice or prompt. This manual is designed merely as a user guide. Ruijie Networks ha s tried its best to ensure the accuracy and reliability of the content when compiling this manual, but it does not guarantee that the content of the manual is completely free of errors or omissions, and all the information in this manual does not constitut e any explicit or implicit warranties.

• Document Version: V1.0
• Date: February 15, 2023
• Copyright © 2023 Ruijie Networks

References

• csm
• csm
• Ruijie Community
• Ruijie Community
• Ruijie Reyee - Redefine your easy network
• Support Center - Ruijie Reyee

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>