Ruijie RG-EW300R Wi-Fi Extender User Manual

Ruijie RG-EW300R Wi-Fi Extender

Product Information

The RG-EW300R is a Wi-Fi extender that helps to extend the coverage of your existing Wi-Fi network. It comes with an Ethernet interface, LED/RESET button, Signal Status LED, and WPS button for easy setup and configuration. The device is easy to install and comes with a user manual and warranty card.

Product Appearance
The RG-EW300R has an Ethernet interface, LED/RESET button, Signal Status LED, and WPS button. The Signal Status LED displays the signal strength of the Wi-Fi network and the System Status LED displays the status of the device. The WPS button is used to establish a WPS network with other routers.

Blinking alternately / Three bars on White / Two bars on / One
bar on / Off| The device restores factory settings. Turn on or off the signal
status LED.
Signal Status LED| N/A| Blinking alternately / Three bars on White / Two bars on / One
bar on / Off| The device is accessing the Wi-Fi network of the primary
router. The signal strength is high/medium / low. The device is
set to the router mode / fails to access the Wi-Fi network of the
primary router.
System Status LED| N/A| Blue (Solid on / Blinking) / Red (Solid on)| The device is functioning properly / the port has made a
successful link. The device is starting up / restoring factory
settings. The network is unreachable.
WPS Button| Short press for less than 2s| N/A| Establish a WPS network with other routers.

Package Contents

• Wi-Fi Extender *1
• User Manual *1
• Warranty Card *1

Product Usage Instructions

Scenario 1: Connect the Device to Other Router

1. Plug in the device and wait for it to start up. The System Status LED will blink blue during startup.
2. Connect to the SSID @Ruijie-sXXXX broadcast by the Wi-Fi Extender and perform configuration. If the configuration page does not pop up, visit 10.44.77.254 by browser.
3. If the device is still in factory status after configuration, it indicates that the device is not properly installed. Move the Wi-Fi extender closer to the primary router and try again.
4. The device will access the network successfully if installed properly. The System Status LED will be solid blue and the Signal Status LED will be solid white with more signal bars indicating a stronger signal. The Wi-Fi extender and the primary router broadcast the same Wi-Fi signal by default. You can also set different Wi-Fis for the Wi-Fi extender and the primary router.
5. If the device fails to connect to the primary router, place the Wi-Fi extender closer to the primary router and try again. The System Status LED will be solid red if the device connects to the primary router but the network is unreachable. Check whether the primary router accesses the Internet.

Scenario 2: Connect the Device to the Primary Router (WPS)

1. Plug in the device and wait for it to start up. The System Status LED will blink blue during startup.
2. Press the WPS button on the primary router and wait for 2 minutes.
3. Press the WPS button on the Wi-Fi extender within 2 minutes.
4. The device will access the network successfully if installed properly. The System Status LED will be solid blue and the Signal Status LED will be solid white with more signal bars indicating a stronger signal. The Wi-Fi extender and the primary router broadcast the same Wi-Fi signal by default. You can also set different Wi-Fis for the Wi-Fi extender and the primary router.
5. If the device fails to connect to the primary router, place the Wi-Fi extender closer to the primary router and try again. The System Status LED will be solid red if the device connects to the primary router but the network is unreachable. Check whether the primary router accesses the Internet.

To better use the Ruijie Reyee products, please read this manual before installation and save it for future reference.

Product Appearance

1. Ethernet Interface
2. LED/RESET Button
   Action| Description
   ---|---
   Long press for more than 5s| The device restores factory settings.
   Short press for less than 2s| Turn on or off the signal status LED.
3. Signal Status LED
   Status| Description
   ---|---

Blinking alternately

| The device is accessing the Wi-Fi network of the primary router.

White

| Three bars on| The signal strength is high.
Two bars on| The signal strength is medium.
One bar on| The signal strength is low.

Off

| 1.  The device is set to the router mode.

2.  The device fails to access the Wi-Fi network of the primary router.

4. System Status LED
   Status| Description
   ---|---

Blue

|

Solid on

| The device is functioning properly. / The port has made a successful link.
Blinking| The device is starting up. / The device is restoring

factory settings.

Red| Solid on| The network is unreachable.
5. WPS Button
Action| Description
---|---
Short press for less than 2s| Establish a WPS network with other routers.

Package Contents

• Wi-Fi Extender *1
• User Manual *1
• Warranty Card *1

Installing the Wi-Fi Extender

Scenario 1: Connect the Device to Other Router

1. The device is starting up after powering on.
   The system status LED is blinking blue. Please wait for 1 to 2 minutes.

2. The startup is complete. The system status LED is solid blue.

3. Connect to the SSID @Rui-jie-sXXXX broadcast by the Wi-Fi Extender and perform configuration. Please visit 10.44.77.254 by the browser if the configuration page does not pop up.

❹ is solid blue. The signal status LED ❸ is off. ❹

| If the device is still in the factory status after the configuration of the Wi-Fi Extender is complete, it indi- cates that the device is not properly installed. Please move the Wi-Fi extender closer to the primary router. Connect to the SSID @Ruijie-sXXXX and try again.
The device accesses the network successfully.| The system status LED is solid blue. The signal

status LED ❸ is solid white.The more signal bars

in solid white indicates the stronger signal.

| The network is reachable. The Wi-Fi extender and the primary router broadcast the same Wi-Fi

signal by default. You can also set different Wi-Fis for the Wi-Fi extender and the primary router.

The device fails to connect to the primary router.| The system status LED ❹ is solid red. The signal status LED ❸ is off.| Please place the Wi-Fi extender- closer to the primary router.
The device connects to the primary router,while the network is unreachable.| The system status LED ❹ is solid red. The signal status LED ❸ is solid white.| Please check whether the primary router accesses the Internet.

Note:

1. You can download the Reyee Router App to get more management functions of the extender, such as turning off the signal status LED and modifying the Wi-Fi name and password.
2. If only one signal bar is on, place the Wi-Fi extender closer to the primary router.
3. You can create a wired network with an Ethernet cable over the 100 Mbps Ethernet port.
4. The connected Wi-Fi extender can access the Wi-Fi network automatically upon the next power-on.
5. You can short press the LED/RESET button ❷ to turn off the LED.

Scenario 2: Connect the Device to the Primary Router (WPS)

1. The device is starting up after power-on.
   The system status LED is blinking blue. Please wait for 1 to 2 minutes.

2. Startup is complete.
   The system status LED is solid blue.

3. Press the WPS button on the primary router.

4. Press the WPS button on the Wi-Fi extender in 2 minutes. The system status LED is solid blue.Three signal bars are blinking alternately.

Place the Wi-Fi extender close to the primary router.

of the Wi-Fi extender is complete, it indi- cates that the device is not properly installed. Please place the Wi-Fi extender closer to the primary router and try again as instructed in the figure.
The device accesses the network successfully.| The system status LED ❹ is solid blue. The signal status LED ❸ is solid white.The more signal bars in solid

white indicates the stronger signal.

| The network is reachable. The Wi-Fi extender and the primary router broadcast the same Wi-Fi signal.
The device fails to connect to the primary router.| The system status LED ❹ is solid red. The signal status LED ❸ is off.| Please place the Wi-Fi extender

closer to the primary router.

The device connects to the primary router, while the network is unreachable.| The system status LED ❹ is solid red. The signal status LED ❸ is solid white.| Please check whether the primary router accesses the Internet.
---|---|---

Note:

1. The device already in the WPS networking status will not be paired again if you press the WPS button.
2. You can short-press the LED/RESET button ❷ to turn off the LED.

Scenario 3: Connect the Device to the Modem Directly

1. The device is starting up after power-on.
   The system status LED is blinking blue. Please wait for 1 to 2 minutes.

2. Startup is complete.
   The system status LED is solid blue.

3. Connect to the modem with an Ethernet cable.
   The system status LED is solid blue.

4. Connect to the SSID @Ruijie-sXXXX broad-casted by the Wi-Fi extender and perform configuration. Please visit 10.44.77.254 by browser to perform configuration if the configu-ration page does not pop up.

Power supply faceplate

❹ is solid blue.

| Please connect to the configured Wi-Fi.
The device fails to connect to the network.| The system status LED

❹ is solid red.

| Please check cable connection and network status.
---|---|---

Note:

1. You can download the Reyee Router App to get more management functions of the Wi-Fi extender, such as turning off the signal status LED and editing the Wi-Fi name and password.
2. The Ethernet interface of the Wi-Fi extender is a 100 Mbps interface.

Router Management

1. App management: You are advised to perform router management on the Reyee Router App.
2. Webpage management: Visit 10.44.77.254 by the browser to perform router management.

Troubleshooting

1. Poor signal strength
   If only one signal bar of the signal status LED ❸ is on after the Wi-Fi extender is installed, you are advised to place the Wi-Fi extender much closer to the primary router.

   • Remark: Please do not install the Wi-Fi extender where the signal strength is the lowest. Instead, place the Wi-Fi extender between the primary router and the location with the poorest signal strength level.

2. Factory setting restoration
   Press the LED/RESET button ❷ for more than 5 seconds. If the system status LED ❹ is blinking blue, the device is restoring factory settings. Please wait for 1 to 2 minutes. If the LED is solid blue, the device has restored factory settings. Perform the installation and configuration again after the device restores factory settings. The default SSID is @Ruijie-sXXXX.

3. Password loss
   You are advised to enter the Wi-Fi password. If the password is still incorrect, please restore the device to factory settings (Press the LED/RESET button ❷ for more than 5 seconds).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>