wuuk Y0110 Wired Smart Doorbell Pro User Manual

wuuk Y0110 Wired Smart Doorbell Pro

WHAT’S INCLUDED

PRODUCT OVERVIEW

WUUK Wired Smart Doorbell Pro

Front

1. Indicator light
2. Camera lens
3. Microphone
4. Doorbell press button
5.  Speaker

Back

1. SYNC button
2. Wire port
3. SD card slot
4. Type C port

WUUK Doorbell Chime

1. SYNC button
2. Indicator light
3. Speaker

SETTING UP THE SYSTEM

Download the WUUK app from the App Store (iOS devices) or GooglePlay Store(Android devices).
Register an account if there is no existing account.

Go to the app homepage. Tap Add Device > add the WUUK Wired Smart Doorbell Pro to your WUUK app.
Follow the on-screen instructions to complete the setup.

TURN OFF THE POWER SUPPLY

Shut off the doorbell power supply. If you’re not sure, shut off the main power supply in your house. Turn the light in your home on/ off to make sure the electricity in your house is properly shut off.

Note: Always be careful when handling electricity wiring. If you’re not comfortable to do it yourself, do consult a qualified electrician.

BYPASS THE EXISTING CHIME

To install a video doorbell, it’s necessary to bypass the existing doorbell chime in your home. Follow these steps to complete the process

• Locate the doorbell chime in your house and remove its cover to reveal the screw terminals marked as
  “TRANS” and “FRONT.”

• Use the provided jumper for existing chime to connect these two terminals, bypassing the doorbell chime. This will not affect the normal operation of the circuit.

• If your doorbell chime has different markings or you have multiple chimes, refer to the help session in the App for custom wiring instructions, or consult a qualified electrician.

• Note that the video doorbell requires the existing chime to be bypassed first to get sufficient power. Without this step, the video doorbell may still power on but will operate unstably.

• Keep in mind that once the jumper is in place, the existing chime will no longer sound.

By following these steps carefully, you’ll be able to bypass your existing doorbell chime and successfully install your new video doorbell.

MOUNT THE DOORBELL

Choose The Way You Want to Install The Doorbell

Height and Location

The WUUK Smart Doorbell series of products is designed and built for outdoor use, and mostly for monitoring your home entrance(s).
We recommend hanging the WUUK Wired Smart Doorbell Pro 3.9ft~4.6ft (120MM~140MM) above the ground.
Avoid placing the doorbell under direct sunlight.
The original package of the WUUK Wired Smart Doorbell Pro contains a 15° Angle Mount. Apply the angle mount if needed.

1-Minute Installation: Apply 3M VHB Tape
Better Prepare The Surface for Strong Bond
Initial tape application to surfaces at temperatures below 50 ° F (10 ° C) is not recommended. If you are in a cold area, warm up the tape by using a hairdryer or other tools.

1. Peel off the red foil that has the 3M VH B texts on it, and attach the backplate to where you want to sit your doorbell.
2. Press hard on the backplate for 5 seconds.
3. Let it be there and dwell for at least 24 hours so the 3M VHB tape can sink into the surface and build the strongest bond.

Screw on(Optional)

*For installing on porous & uneven surfaces such as concrete, stone, limestone, brick; Or you choose to install this way.
Mark 2 drill hole positions using the doorbell locating pad provided. Use a bit to drill holes in your wall and insert the anchors.

• Install anchors – on stucco, brick, or concrete (Optional)
• Screw it in – on particleboard, wood, and paints
• Secure your WUUK Doorbell backplate on the wall using the four screws provided.

Connect the Wires

Note: Make sure the wires go through the backplate.

Connect the wires coming out of your wall to the screws on the back of your WUUK Doorbell. Either wire can connect to either screw. The order doesn’t matter.

Attach The Wire Extensions (Optional)

If you have trouble connecting the wires coming out of your wall to the back of your WUUK Doorbell, use the provided wire extensions and wire nuts.
Feed all the wires, and the wire nuts, if you used them, into your wall.

Hook the Doorbell

Then hand the doorbell onto the wall mount.
Match the top hook on the backplate first, then snap the bottom. Press the lower part of the doorbell until you hear a slight clicking sound.

TURN THE DOORBELL ON

Switch the master circuit breaker to ON.

Wait until the doorbell indicator light flashes red. Then follow the on-screen instructions in WUUK App to connect the video doorbell to your home Wi-Fi.

UNDERSTAND THE INDICATOR LIGHT

WUUK Wired Smart Doorbell Pro

• Solid Blue: Power on and working properly

• Solid Red: System is initializing or rebooting

• Flashing Blue: Disconnected from the Internet

• Flashing Red: Pairing Mode, Ready for setup

• Flashing blue and red alternately: Firmware upgrade in progress

WUUK Doorbell Chime

• Solid Blue: Power on and working properly

• Solid Red: System is initializing or rebooting

• Flashing Blue: Disconnected from the Internet

• Flashing Red: Pairing Mode, Ready for setup

• Flashing blue and red alternately: Firmware upgrade in progress

CUSTOMER SERVICE

For troubleshooting, check the WUUK app >Account> Help Center for more reference and live chat with Customer Support agents if needed.

• Warranty: 12-month Limited Warranty
• Call Us: United States +1 (415)881-5715
• Email Us: hello@wuuklabs.com

WU UK Labs Corp. All rights reserved.
WUUK and WUUK Logo are trademarks of WUUK Labs Corp., registered in the United States and other countries. All other trademarks are the property of their respective owners.

SAFETY STATEMENT FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the Limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These Limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This equipment complies with FCC radiation exposure Limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement:
This device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3(8) /NMB-3(8).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>