Rockville RockShelf V2 Home Theater Bookshelf Speakers OWNER’S MANUAL
- June 12, 2024
- RockVille
Table of Contents
Rockville RockShelf V2 Home Theater Bookshelf Speakers
Thank you for purchasing these Rockville ROCKSHELF home bookshelf speakers. Please read this owner’s manual carefully for proper use of your Rockville ROCKSHELF speakers. Should you need assistance, please call our technical helpline at 1-646-758-0144, Monday through Friday, 9 am to 5 pm EST.
IMPORTANT SAFETY INSTRUCTIONS
- Make sure to match your speaker and amplifier power ratings. Failure to do so can result in permanent damage to your speakers.
- Distortion is an indication that the amplifier or speaker is operating beyond its design limits. If you hear distortion, immediately turn down the volume to avoid permanent damage.
- Do not place these speakers on an unstable cart, stand, bracket, or table. The speaker may fall, causing serious injury to a child or adult and serious damage to the unit.
- Do not use these speakers near water; for example, near a bathtub, sink, in a wet basement, or near a swimming pool.
- The speakers should be situated away from heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
- Clean only with a soft damp cloth.
CONNECTING THE SPEAKERS
These speakers are passive and thus require an amplifier or receiver to give them power. They can be connected to any 4 or 8-ohm amplifier. When using the ROCKSHELF 4 ohm model, you can connect one speaker per amp channel. When using the 8-ohm model, you can connect up to 2 speakers per channel as long as your amp is 4 to 8 ohm capable. If your speakers are relatively close to the signal source (50 feet or less), 16 gauge wire can be used. For longer distances, 12 or 14-gauge wire is recommended. Be sure to observe proper polarity by ensuring that the wire from the red speaker terminal is connected to the red or positive terminal of the signal source and that the wire from the black speaker terminal is connected to the black or negative terminal of the signal source.
The ROCKSHELF features 5-way binding posts which can accept various types of connections:
- Banana plugs can be inserted into the open end of the binding post.
- Spade terminals can be placed around the metal post and clamped by the screw-down cap.
- Looped wire can be wrapped around the binding post and clamped by the screw-down cap.
- Straight wire can be inserted into the hole drilled through the bottom of the binding post and clamped down by the screw cap.
- Pin connectors can be inserted into the hole drilled through the bottom of the binding post and clamped down by the screw cap.
MAGNETIC GRILLS
The grills included with your ROCKSHELF speakers use high-strength magnets to hold them in place. They can be easily removed for cleaning or for aesthetic purposes. To remove them, place one finger on each top corner of the grill and gently pull the grill towards you. To replace, position the grill squarely over the face of the speaker and it will attach itself. Align the grill if needed.
POSITIONING THE SPEAKERS
To place the speakers, start with them placed directly in front of your primary listening position. Make sure the tweeters are as close to ear level as possible. As you are listening to music, make sure to pay close attention to the quality and separation of vocals and instruments. You can move the speakers closer together or further apart to optimize your listening experience, but make sure they are set as far away from the listener as each other.
Always listen to several musical selections so that you hear lows (bass), (vocals and horns), and highs (treble) from a variety of instruments and vocalists. Allow your speakers a “breakin” period before permanently positioning them. To break in your speakers: at a moderate to low level, play a variety of music through the speakers over a day or two. This will help to prepare them for regular use and optimal performance.
CABINET CARE
The finish of your ROCKSHELF speakers can be maintained by periodically wiping it down with a lightly dampened fiber cloth. The grills can be brushed or vacuumed to remove dust.
TROUBLESHOOTING
| PROBLEM | SOLUTION |
|---|---|
| No sound | 1. Please make sure your speaker wires/connections are inserted |
completely into the speaker terminals and that all connectors are properly seated.
2. These speakers require power, please make sure your receiver has amplified speaker outputs. If it does not, we are happy to help you find the right receiver or amplifier for your setup. Email us at [email protected].
3. Please make sure your active audio source (cd, aux, tape, etc.) is selected on your receiver.
FEATURES
- Audiophile-grade black Kevlar woofer cone for excellent mid and low-frequency response
- Ultra-stiff Polypropylene dust cap on the woofer
- Rubber surrounds on the woofer
- Silk dome tweeter gives crisp and realistic-sounding highs
- Gold-plated 5-way binding post terminals can accept banana, bare wire, spade terminals, and more
- Detachable magnetic grill
- Wall mount hanging bracket
- Cabinet material: Top quality 12mm MDF with a beautiful wood grain finish
- Colors: black, white, classic
SPECIFICATIONS
- RMS power: 50 watts each /100 watts per pair
- Peak power: 200 watts each/400 watts per pair
- Woofer: 6.5˝ Kevlar cone
- Tweeter: 1˝ silk dome tweeter
- 1˝ aluminum voice coils
- Frequency response (±3db): 65Hz – 20KHz
- Sensitivity: 87dB 1W/1m
- ROCKSHELF 64 impedance: 4 ohms
- ROCKSHELF 68 impedance: 8 ohms
- Dimensions of each speaker: 11.81˝(H) x 7.06˝(W) x 6.43˝(D)
- Weight per speaker: 6lbs
RockvilleAudio.com © 2020 ROCKVILLE // Features and specifications are subject to change and or improvement without notice.
FREQUENTLY ASKED QUESTIONS
What is the power rating of the Rockville RockShelf V2 bookshelf speakers?
The Rockville RockShelf V2 bookshelf speakers have a power rating of 150 watts RMS per pair (75 watts RMS per speaker).
What size are the woofers in the RockShelf V2 speakers?
The Rockville RockShelf V2 bookshelf speakers are equipped with 4
Do the speakers come with speaker grills?
Yes, the RockShelf V2 bookshelf speakers come with detachable speaker grills.
What type of enclosure design do the speakers use?
The RockShelf V2 bookshelf speakers feature a ported enclosure design to enhance bass response.
Can the RockShelf V2 speakers be bi-amped or bi-wired?
No, the Rockville RockShelf V2 speakers are not designed for bi-amping or bi- wiring.
Do the bookshelf speakers have built-in Bluetooth connectivity?
No, the RockShelf V2 speakers do not have built-in Bluetooth connectivity.
Are the Rockville RockShelf V2 speakers sold as a pair or individually?
The RockShelf V2 bookshelf speakers are typically sold as a pair.
What is the impedance of the RockShelf V2 speakers?
The Rockville RockShelf V2 bookshelf speakers have an impedance of 4 ohms.
Do the speakers include a subwoofer output?
No, the RockShelf V2 bookshelf speakers do not have a dedicated subwoofer output.
Can the Rockville RockShelf V2 speakers be wall-mounted?
Yes, the RockShelf V2 bookshelf speakers have mounting holes on the back for wall mounting.
What is the frequency response range of the speakers?
The Rockville RockShelf V2 bookshelf speakers have a frequency response range of typically 60Hz - 20kHz.
Are the speakers magnetically shielded to prevent interference with nearby electronics?
Yes, the RockShelf V2 bookshelf speakers are magnetically shielded to minimize interference.
Can you use the RockShelf V2 speakers as part of a home theater system?
Yes, the Rockville RockShelf V2 bookshelf speakers can be used as front or surround speakers in a home theater setup.
What are the dimensions of the RockShelf V2 speakers?
The dimensions of the Rockville RockShelf V2 bookshelf speakers are typically around 9.25
Do the speakers come with speaker wire connections or banana plug terminals?
The RockShelf V2 bookshelf speakers have spring-loaded speaker wire terminals for easy connection.
DOWNLOAD THE PDF LINK:Rockville RockShelf V2 Home Theater Bookshelf Speakers OWNER’S MANUAL