COMMSCOPE M-LOC Series Bird Proof Jumper Instruction Manual

June 12, 2024
CommScope

M-LOC Bird proof Jumper Assembly
for HELIAX® M-LOC series Patent Pending

M-LOC Series Bird Proof Jumper

  1. Remove any packaging and dust caps from the M-LOC and the device, uncoil the M-LOC assembly. Hold the bent flange portion of latch back toward cable strain relief.

  2. Align the key on the housing with the keyway opening in the device. Orient the holes in the M-LOC connector to the panel mount connectors.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 2

  3. Align the M-LOC connector with the antenna mating interface and push firmly into place, eliminating gap between connector housing and bulkhead. While mating, a slight back and forth motion on the housing/ cables will assist in centering and seating the port connectors into alignment. Do Not twist the jumpers. Push the latch toward the base of the antenna to engage the latch pins at the base of the connector housing.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 3

  4. Apply force on the bent flange of the latch until the detents in the arms pop over the pins. There will be an audible and tactile click. To reduce hand strain, a screwdriver may be used.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 4

  5. To remove the M-LOC connector pull latch flange away from the base of the antenna. To reduce hand strain, a flat blade screwdriver may be inserted in the slot above the latch flange and pulled down against the flange.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 5

  6. Grasp M-LOC connector housing, hold bent flange portion of latch back toward cable strain relief, pull the connector away from device. A slight back and forth motion on the housing helps to release the pod connectors.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 6

  7. Route and form the jumper assembly with HELIAX® SureGuard weatherproofing system installed prior to attaching the coupling nuts.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 7

  8. Torque the connection using the appropriate wrenches or tool.
    7-16 DIN male connector: 25-30 N•m (18-22 ft-lb)
    4.3-10 male connector: 5-8 N•m (4-6 ft-lb)
    NEX10 male connector: 1.5 N•m (1.1 ft-lb)
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 8

  9. Push 1 and twist 2 the boot counter- clockwise over the male coupling nut. Pull down slightly 3 and push back up 4 to flatten the top of the boot. Boot MUST look like Properly Seated illustrations below.

  10. Pull back conduit with gasket through the picture direction shown stopped by sureguard V2.0.
    Make sure the gasket is seated well into the conduit.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 10
    WARNING
    Suregard V2.0 boot should not be pushed up over the square section of the connector.
    Be careful only tighten the cable gland nut after all cable fastening and movement is completed.

  11. Push cap to cover sureguard V2.0 in, keep the cap as line as sureguard.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 11

  12. Screwed cable gland nut by hand as shown.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 12

  13. Do not hold the connector and bend the cable directly behindit, start bend 30mm min away from the cap end as picture shown.
    REWORK:
    Pull back gasket along with conduit, then pull back sureguard V2.0
    For jumper assemblies without sureguard boots applying weather proofing to 4.3-10 assemblies is recommended (contractor supplied).
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 14Wrap one layer of insulation tape
    Wrap three layers of waterproof tape
    Wrap one layer of insulation tape

M-LOC Bird proof Jumper Assembly

for HELIAX® M-LOC series Patent Pending

  1. The latch orientation is reversible if required.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 15

  2. Align the hole of the latch arm with the hinge pin of the connector body and pull gently away from the body, just enough to clear the end of the hinge pin. Then pull the latch arm away parallel to the body.
    Ensure that the arm doesn’t  get caught on the retention groove or damage may occur to the hinge pins.
    Roll the latch around and off the opposite pin.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 16

  3. Once the latch is removed, bend the two arms back to 90° so they will fit tightly back onto the housing. To reattach, latch one arm over a hinge pin then roll other arm over the housing and onto the other hinge pin.
    COMMSCOPE M-LOC Series Bird Proof Jumper - Figure 17

M-LOC cluster connector bottom installation video

COMMSCOPE M-LOC Series Bird Proof Jumper - qr codehttps://eqrcode.co/a/hkque0

M-LOC cluster connector back installation video

COMMSCOPE M-LOC Series Bird Proof Jumper - qr code 2https://eqrcode.co/a/olZbn9

CommScope
1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339
828-324-2200 800-982-1708
www.commscope.com
Technical Support
+1 888 297 6433, Option 3 (Toll Free US and Canada)
+1 49-9099-69-333
https://www.commscope.com/wisupport (open a ticket)

Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

© 2022 CommScope

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CommScope User Manuals

Related Manuals