COMMSCOPE P040-0097 Top Mounting Kits Instructions
- June 1, 2024
- CommScope
Table of Contents
P040-0097 Revision A,
October 2023
Mounting Kits For
Small cell Antennas
P040-0097 Top Mounting Kits
MC-MNT-SIDE-370: Mounting systems for cylindrical pipe installations (50-250mm
pipe diameter)
Suitable for small cell cylindrical antennas with a weight less than 20KG and
dimensions less than diameterheight: 370610mm.
Installation Preparations
All fasteners must be tightended to the defined torque value after onsite
installation, see mounting kit installation diagrams on following pages for
correct torque recommendations.
Figure 1 Installation tools lists
Installation tools list
Table 1 Installation tools lists
| Tool | Size | Torque Range |
|---|---|---|
| Torque wrench | 10mm | 14Nm (11ft.lbs) |
| Socket | 10mm | 14Nm (11ft.lbs) |
| Torque wrench | 19mm | 58Nm (43ft.lbs) |
| Socket | 19mm | 58Nm (43ft.lbs) |
| Torque wrench | 36mm | 100Nm (74ft.lbs) |
| Socket | 36mm | 100Nm (74ft.lbs) |
| ITEM NO. | DESCRIPTION | QTY |
| --- | --- | --- |
| 1 | MOUNTING BRACKET,W/GASKET | 1 |
| 2 | POLE CLAMP,MAIN BODY | 1 |
| 3 | POLE CLAMP,MAIN BODY | 1 |
| 4 | SCR,HCS,HEX,M24X80,STL,GALV | 1 |
| 5 | SCR,HCS,HEX,M6X40,SST,PASS | 2 |
| 6 | BOLT,CARRIAGE,M12X270,STL,GALV | 2 |
| 7 | BOLT,CARRIAGE,M12X45,STL,GALV | 4 |
| 8 | WSHR,FLT,M24,25X44X4,STL,GALV | 1 |
| 9 | WSHR,FLAT,M6,6.4x12x1.6,SST,PASS | 4 |
| 10 | WSHR,FLAT,M12,13X40X6,STL,GALV | 2 |
| 11 | WSHR,FLT,M12,13X24X2.5,STL,GALV | 4 |
| 12 | NUT,HEX,M24,STL,GALV | 2 |
| 13 | NUT,HEX,M6-1,SST,PASS | 4 |
| 14 | NUT,HEX,M12,STL,GALV | 12 |
| 15 | WSHR,FLAT,M24,25X100X5 STL,GALV | 1 |
Part Lists
GENERAL INFORMATION
After removing the antenna from its shipping container carefully inspect it to
ensure there is no shipping damage. If the antenna is to be hoisted into
position, ensure the lifting eye bolt is correctly installed. Ensure the
antenna is securely held during hoisting to avoid rotation on the lifting eye
bolt.
INSTALLATION INSTRUCTIONS
Refer to Figures 2 and 3 for mounting and arrow direction. It is recommended
that the mounting holes be marked and made ready in the mounting surface prior
to installing the antenna.
The arrow of each antenna is shown on brakcet one side. The direction of each
antenna must be considered prior to mounting to ensure desired performance.
MC-MNT-SIDE-370
SAFETY NOTICE
The installation, maintenance, or removal of an antenna requires qualified,
experienced personnel. CommScope installation instructions are written for
such installation personnel. Antenna systems should be inspected once a year
by qualified personnel to verify proper installation, maintenance, and
condition of equipment.
CommScope disclaims any liability or responsibility for the results of
improper or unsafe installation practices.
It is recommended that transmit power be turned off when the field
installation is performed. Follow all applicable safety precautions as shown
on this page.
Do not install near power lines.
Power lines, telephone lines, and guy wires look the same.
Assume any wire or line can electrocute you.
Do not install on a wet or windy day or when lightning or thunder is in the
area. Do not use metal ladder.
Wear shoes with rubber soles and heels. Wear
protective clothing including a long-sleeved shirt and rubber gloves.
Visit our website at www.commscope.com or contact
your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks,
respectively, of CommScope, Inc. P040-0097 A (10/23)
www.commscope.com
© 2023 CommScope, Inc. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>