COMMSCOPE FACT Fiber Splice Drawers Installation Guide

CommScope FACT Fiber Splice Drawers

Installation Instructions

The FACT Splice Drawer is a product designed to facilitate the splicing of fiber optic cables. Below is information on how to install and use the product.

General Product Information

• The FACT Splice Drawer is a chassis used for splicing fiber optic cables.
• The product comes with a bracket kit according to the chassis configuration.

Warnings and Caution

• Ensure that the rack is prepared with the brackets in the correct position before installing the chassis.
• When opening the cover, apply force to the cover in the direction of the arrows to avoid damaging the product.
• Be careful when handling the fiber picker to avoid damaging it.

Kit Content

• 1x FACT Splice Chassis (as ordered)
• 1x Bracket Kit (according to chassis configuration)

Mounting FACT Chassis in Rack

1. Prepare the rack with the brackets in the position where you want to install the FACT Chassis by sliding them in.
2. Align the FACT Chassis with the brackets on both sides.
3. Slide the FACT Chassis into the brackets until you hear a clicking noise.

Dismounting FACT Chassis

1. Open the upper drawer marked with a blue marking at the bend control.
2. Pull the blue puller locks on both sides to the unlocked position.
3. Slowly slide the FACT Chassis out by pulling simultaneously on both sides with both hands.

Opening the Cover

1. Apply some force by pinching them together in the direction of the arrows to unlock the cover.
2. Rotate the cover upwards to open it.

Removing the Cover

Notes can be made on the label when the cover is closed. The label can also be removed if preferred. It is held in place in the four corners. Simply slide it out of the four corners to remove it.

Handling the Fiber Picker

The fiber picker is located on the left or right as indicated by the arrows. To remove it, simply pull it upwards until it releases from the snapping features.

Trade-marks

This product is covered by one or more U.S. patents or their foreign equivalents. For patents, see www.commscope.com/ProductPatent/ProductPatent.aspx

Contact Information

Visit our website or contact your local CommScope representative for more information. For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://www.commscope.com/SupportCenter

General product information

• The FACT multi-purpose splice chassis (FACT-xESPLxxx) feature Single Circuit and Single Element fiber manage-ment system technology.
• One FACT element is designed to enter from each side with max. 8 FOPT-tubes, 48 single-pigtails 1,8mm or 48x 900µm IFC cable.
• For cable installation and fiber routing into the chassis, please refer to the appropriate cable kit installation instructions (FACT-ACCCTUxxx).

Warnings and caution

• Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimum bend radius. Always observe the recommended bend radius limit when installing fiber optic cables and patch cords.
• Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any optical fiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end.

Kit content

• FACT Splice Chassis (as ordered)
• Bracket Kit (according to chassis configuration)

Mounting FACT Chassis in Rack

• Step 1: Prepare the rack with the brackets on the position where you want to install the FACT Chassis (by sliding them in).
• Step 2: Align the FACT Chassis with the brackets on both sides.
• Step 3: Slide the FACT Chassis into the brackets until you hear a “clicking noise”.

Dismounting FACT Chassis

Step 1: Open the upper drawer (releasable). This one is marked at the front (blue marking at the bend control).

Step 2: Pull the blue puller locks (make sure both sides are in the unlocked position).

Step 3: Slowly slide the FACT Chassis out (pull simultaneously on both sides, with both hands).

Opening the Cover

Step 1: Apply some force (pinching together in the direction of the arrows) to unlock the cover. Rotate the cover upwards to open it.

Step 2: The cover will stay in the open position if this is rotated about 85°.

Removing the Cover

Step 1 : To remove the cover, rotate the cover about 10° upwards .

Step 2: Pull the cover in the 10° angle towards the front. The cover will pop out of the hinge. To re-assemble the cover, repeat the 2 previous steps the other way around.

Handling the Label

Notes can be made on the label when the cover is closed (this acts as a support). The label can also be removed if preferred. It is held in place in the four corners. Simply slide it out of the four corners to remove.

Handling the Fiber Picker

The fiber picker is located on the left or right (as indicated by the arrows). To remove it, simply pull it upwards until it releases from the snapping features.

Trade-marks:

• All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope,
• Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. CommScope is committed to the highest standards of business integrity and environmental sustainability, with a number of CommScope facilities across the globe certified in accordance with international standards, including ISO9001, TL 9000, and ISO 14001. Further informa-tion regarding CommScope’s commitment can be found at: www.commscope.com/About-Us/Corporate-Responsibilityand-Sustainability.

Contact Information

• Visit our website or contact your local CommScope representative for more information.
• For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://www.commscope.com/SupportCenter
• This product is covered by one or more U.S. patents or their foreign equivalents. For patents, see  www.commscope.com/ProductPatent/ProductPatent.aspx
• © 2020 Commscope, Inc. All Rights Reserved
• TC-40180-IP-EN Rev A, May 2020www.commscope.com

References

• Support Center | CommScope

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>