integral LED Evofire Fire Rated Downlight Instruction Manual
- June 12, 2024
- integral LED
Table of Contents
Evofire Fire Rated Downlight
Instruction Manual
Evofire Fire Rated Downlight
- UK design and engineered for LED lamps only.
- Completely open construction to allow for good air circulation for improved lifetime and the highest output possible for LED lamps.
- Fire rated for 30 minutes, 60 minutes and 90 minutes ceilings to BS 476: Part 21:1987 by UKAS approved Exova Warringtonfire when installed in ceilings of approved construction.
- Patent pending construction.
- IP65 dust and moisture sealed from the front when installed correctly.
- Models supplied with ‘Insulation Guard’ are suitable for coverage by thermal and acoustic insulation e.g. loft insulation. Not suitable for blown insulation.
- Compliant with Part B (Fire), Part C (Condensation), Part E (Acoustic), Part L (Conservation and Fuel and Power, when used with high quality LED lamps such as Integral).
- Compliant with BS EN ISO 140-3:1995, BS EN ISO 140-6:1998, BS EN ISO 717-1:1997, BS EN ISO 717-2:1997.
Important Details – Please read prior to installation
- Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
- This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
- This product must not be used with non-LED lamps.
- This downlight range is designed to be installed in a ceiling tile/plasterboard/solid material, with a thickness of 3mm (minimum) to 30mm (maximum).
- This product is for indoor use only.
- The product should NOT be covered with insulation material at any time. Unless using a model with an insulation guard.
- Minimum clearance is 50mm above the installed fitting and should NOT be installed within 50mm of any joist.
- Earth wire is provided if required.
- These instructions refer to an LED lamp with a GU10 lamp base. For instructions on how to install an LED lamp with a MR16 base please visit our website at www.integral-led.com/evofire-mr16
Generic Installation Details
- Ensure the mains power is turned OFF and cannot be unexpectedly reconnected.
- For new installations use cutting tools suitable for the material and carefully cut the required hole. Refer to box packaging for cut-out dimension.
- For refurbishment/retrofit installations, ensure that existing hole is suitable and strong enough to hold the new downlight. Support the surrounding area if required. If the existing hole is larger than the prescribed cut-out, an additional adapter is available.
- Connect the AC/mains cable. Where a terminal block is provided, incoming cable connections are; L = Live power conductor (brown wire), N = Neutral power conductor (blue wire), Earth green/yellow wire).
Generic Installation Details
Refer to the correct instruction pages for your product.
| Integral Code | EAN Barcode | Go to figures |
|---|
Round
ILDLFR70D001| 5055788228325| A1 to A8, D1
ILDLFR70D001-4| 5055788228356| A1 to A8, D1
ILDLFR70D002| 5055788228387| A1 to A8, D1
ILDLFR70D002-4| 5055788228417| A1 to A8, D1
ILDLFR70D015| 5055788236481| A1 to A8, D1
ILDLFR70D016| 5055788236511| A1 to A8, D1
ILDLFR70D017| 5055788238317| A1 to A8, D1
ILDLFR70D021| 5055788238447| A1 to A8, D1
ILDLFR70D011| 5055788228905| A1 to A8, D1
ILDLFR70D012| 5055788228943| A1 to A8, D1
ILDLFR70D028| 5055788253792| A1 to A8, D1
ILDLFR70D029| 5055788253815| A1 to A8, D1
ILDLFR70D045| 5055788268123| A1 to A8, D2
ILDLFR70D046| 5055788268130| A1 to A8, D3
ILDLFR70D047| 5055788268147| A1 to A8, D4
ILDLFR70D048| 5055788268154| A1 to A8, D5
Round w/Insulation Guard
ILDLFR70D003| 5055788228448| A1 to A8, D2
ILDLFR70D003-3| 5055788228479| A1 to A8, D2
ILDLFR70D004| 5055788228509| A1 to A8, D2
ILDLFR70D004-3| 5055788228530| A1 to A8, D2
ILDLFR70D013| 5055788236429| A1 to A8, D2
ILDLFR70D014| 5055788236450| A1 to A8, D2
ILDLFR70D018| 5055788238348| A1 to A8, D2
ILDLFR70D020| 5055788238416| A1 to A8, D2
Integral Code| EAN Barcode| Go to figures
---|---|---
Round Adapter
ILDLFR70D005| 5055788228561| B1, B2, A1 to A8
ILDLFR70D006| 5055788228592| B1, B2, A1 to A8
ILDLFR70D019| 5055788238386| B1, B2, A1 to A8
ILDLFR70D030| 5055788253921| B1, B2, A1 to A8
ILDLFR70D049| 5055788270812| B1, B2, A1 to A8
ILDLFR70D050| 5055788270829| B1, B2, A1 to A8
Square
ILDLFR70D007| 5055788228622| A1 to A8, D1, E1, E2
ILDLFR70D008| 5055788228653| A1 to A8, D1, E1, E2
Square w/Insulation Guard
ILDLFR70D009| 5055788228684| A1 to A8, D2, E1, E2
ILDLFR70D010| 5055788228714| A1 to A8, D2, E1, E2
Recessed
ILDLFR70E001| 5055788228745| C1 to C8, D1
ILDLFR70E002| 5055788228776| C1 to C8, D1
ILDLFR70E003| 5055788236542| C1 to C8, D2
ILDLFR70E004| 5055788236573| C1 to C8, D2
Warranty/Technical and contact information are all available at www.integral- led.com
Integral LED is a division of Integral Memory plc:
Unit 6, Iron Bridge Close, Iron Bridge Business Park, London, NW10 0UF, UK
EC/REP: Integral Europe BV 2801 DG, NL
EVOFRDLINSTR04 GRP1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>