Integral LED IS 1001 Lux Mini LED Downlights Instruction Manual

: June 10, 2024
: integral LED

Table of Contents

Integral LED IS 1001 Lux Mini LED Downlights
Product Information
Product Usage Instructions
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Integral LED IS 1001 Lux Mini LED Downlights

Integral-LED-IS-1001-Lux-Mini-LED-Downlights-product -
Copy

Product Information

The product is an IS 1001 LED light from Integral LED, a division of Integral Memory plc. The product is manufactured in the UK and the Netherlands. Technical and warranty information can be found at www.integral- led.com.

Product Usage Instructions

Remove the IS 1001 LED light from its packaging.
Read and understand all safety information provided in the user manual.
Install the LED light in the desired location.
Connect the LED light to a power source using the provided cables.
Turn on the power source to activate the LED light.
Adjust the brightness of the LED light as needed using the provided controls.
If any issues arise, refer to the user manual for troubleshooting tips or contact Integral LED for technical support.

It is important to follow all safety instructions and use the product only as intended to ensure proper functioning and avoid any hazards or damage.

Safety Information

Refer to the user manual for safety information in multiple languages.

A – Follow the Instruction Sheet to ensure safe and reliable operation. Retain for future reference.
Products should be installed by a qualified Electrician in accordance with International Wiring Regulations.
B – Switch off mains supply before installation. Isolate from mains supply before any maintenance.
Integral LED accepts no responsibility for modified products.
Integral LED Adaptors, Connectors and Track luminaires must only be used with the Track system for which they have been designed.
If Dimmer is installed it must be specifically rated as suitable and compatible with the equipment used.
Touching a reflective surface must be avoided.
Check that the rating on the product label conforms to the mains supply.
C – For indoor use only.
D – Class I – This product should be Earthed.
E – Class II – This product does not require Earthing.
F – Class III – SELV Luminaires to be used with Double Insulated, Extra Low Voltage, Safety Isolating Transformers or LED drivers.
Do not interconnect Class III products with Class I or Class II.
Metal enclosed, Class II and Class III products must not be mounted in contact with or close to Earthed metalwork.
G / H – Luminaires not suitable for direct mounting on/in normally flammable surfaces.
I – Unless otherwise marked, products are IP20 (ordinary). Do not operate in damp or corrosive situations. If the luminaire is to be exposed to dust or moisture the appropriate IP(XX) rated luminaire should be used.
Use only the correct replacement lamp as indicated on the product label.
J – Class II product earth wire continuity terminal
K – Emergency Luminaires – Do not switch off the UN-switched mains supply after installation. If the interruption is unavoidable, the batteries must be disconnected or damage to the batteries or the lamp may occur. Testing – Switch on the mains supply and check that the charge indicator (LED) is ON. Leave the luminaire on continuous charge for 24 hours. Simulate mains failure and check that the lamp operates for 3 hours. If full duration of 3 hours is NOT achieved, repeat the charge/discharge cycle as battery packs may have discharged in stock and will require conditioning.
L – Not suitable for covering with thermally insulating material.
Luminaire should be cleaned by using a soft damp soapy cloth. Do not use solvents.
M – This electrical product MUST be recycled in accordance with WEEE Directive.
N – Dimmable. Dimming Compatibility: It is the responsibility of the Buyer (or its appointed specifier, or qualified electrical installer) to ensure compatibility between Seller’s Goods being installed and the dimming switch (or dimming system) intended to control the Goods. Under no circumstances shall the Seller be held responsible for such incompatibility issues.
O – Risk of Electric Shock.
P – Observe minimum and maximum ambient operating temperatures of the device as specified in the datasheet and/ or instruction manual.
Q – This product contains a light source of energy efficiency class . Unless marked, products are classed as per the official energy rating label on the packaging.