TECNO Spark 10 Smartphone User Manual

June 12, 2024
TECNO

TECNO Spark 10 Smartphone

Product Information

SPARK 10

  1. Front Camera
  2. Volume + key
  3. Volume – key
  4. Power key & side fingerprint sensor
  5. NFC

SIM/SD Card Installation

  1. Power off the mobile phone.
  2. Refer to the user manual for a picture guide on how to install the SIM and SD card.

Charging the Phone

You can charge your SPARK 10 using a charger or by connecting it to a computer using a USB cable. The USB cable is included with the phone.

Note: Only use the TECNO charger and cables provided with the phone. Using other chargers or cables may cause damage to the device and invalidate your phone warranty.

FCC Caution

Labeling requirements:

The SPARK 10 complies with Part 15 of the FCC Rules. The operation of this device is subject to the following conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Information to User:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Specific Absorption Rate (SAR) Information:

This mobile phone meets the government’s requirements for Specific Absorption Rate (SAR).

HiOS:

The SPARK 10 runs on HiOS, which is based on the AndroidTM operating system. Android is a trademark of Google LLC.

Know your phone

  1. Front Camera
  2. Volume + key
  3. Volume – key
  4. Power key & side fingerprint sensor
  5. NFC

SIM/SD card installation

  1. Power off your mobile.
  2. Refer to the following picture for SIM / SD card installation.

Charging the phone

  1. You can charge your device using a charger or by connecting it to the computer using a USB cable (which comes with the phone).
  2. Use only the TECNO charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labeling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Information to the user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio TV technician for help.

Specific Absorption Rate (SAR) information:

This mobile phone meets the government’s requirements for exposure to radio waves.
The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: KI5q(FCC ID: 2ADYY- KI5Q)has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.05 W/kg and when properly worn on the body is 1.12 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with R exposure requirements and should be avoided. Use only the supplied or an approved antenna.
HiOS runs on Android™” os.
Android is a trademark of Google LLC.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals