WOHOME S100 2.1 CH Soundbar Speaker System User Manual

WOHOME S100 2.1 CH Soundbar Speaker System

Important Safety Instructions

1. Read these Instructions.
2. keep these instrictions
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use tnis apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.Install in
8. Do not install near any heat sources such as radiators, heat registers,stoves. or other appara- tus(including amplifiers)that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not nt into vour out et. consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta- dies. ano te point where ter exictron the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Special note : When placing vour unit on a lacquered or natural hihish, protect your turniture with a cloth or orner protecuve marena.

Additional Warnings

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,such as vases, shall be placed on apparatus.

Caution marking is located at the rear or bottom of te apparats. The marking information is located at the rear or bottom of apparatus.

FCC Warnings

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the coupment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interterence. and Withis device must accept any interterence received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equioment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the cause harmin interterence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. FCCRadiationExposureStatement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

What’s in the box

Make sure you read all the safety information before you use this product.

Overview

Sound bar main unit

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Sound Bar LED Indicator

The LED indicator on the sound bar gives you information about the status of the soundbar.

Install or replace the remote batteries

Battery type: 1.5V AAA Alkaline battery × (Battery not supplied, please use yours)

Using the Remote

Using &Connect to your TV

Optical

• Step 1, Turn off the sound bar and TV, connected the sound bar to the TV through the optical cable. (Remove the white cover on cable).
• Step 2, Turn on the sound bar, press the “INPUT” on the sound bar remote, then select the input mode “OPT” which is shows on the LED display.
• Step 3, Turn on the TV, press the home on the TV remote, go to TV setting ›audio(sound)-›TV speaker–select external speaker or turn off TV speaker, save the setting, then back to audio (sound setting)–select expert setting — digital audio output (or optical output)–select PCM (some TV called SPDIF or optical ), Save the setting.
• Step 4, Play TV show to test the sound bar.

Kindly Note: for optical connection, please change TV audio output to PCM(or SPDIF and optical) and external speaker, otherwise you will get cracking noise or no sound.

Kindly Note: TV settings may differ according to TV model’s difference, if the listed method can not work, or your TV is not listed, please contact us via service mail: support@wohomeshop.com, or contact the TV manufacturer for help, thank you!

AUX

• Step 1, Choose line in cable (3.5mm to 3.5mm) or RCA cable connect the soundbar to your TV.
• Step 2, Turn on the sound bar, press the “INPUT” on the sound bar remote, then select the input mode “AUX” which is shows on the LED display.
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV setting > audio(sound)-›TV speaker–select external speaker(turn off TV speaker), save the setting. For some TVs, please back to audio(sound)-›select analog output-› select the “Variable”,save the setting).
• Step 4, Play TV show to test the sound bar.

ВТ

The BT connection

1. Press the “INPUT” on the sound bar remote, then select the input mode “BT” which is shows on the LED display, the “BT” will be flash.
2. Turn on BT on the BT device. (see the device’s manual for more information)
3. Select “Soundbar S100″from the device BT list, connect it. When your BT device is connected, the LED display will stop flash.
4. Play music files from the connected device via BT, throught the Soundbar.

• You cannot connect more than one BT device at a time.
• If your device requests a password, enters the default “0000”.
• Only work with the device which can output BT signal, it can not work with some devices can not output BT signal such as headphones.
• Disconnect the Bluetooth connection when the connection fails or “Soundbar S100 “cannot be found in the device list.

USB

1. Connect your USB drive to the USB jack on the soundbar.
2. Press the “INPUT” on the sound bar remote, then select the input mode “USB” which is shows on the LED display.
3. Play music to test.

Kindly Note: only for USB flash drive to play MP3 music and update firmware, can not compatible with other usb devices.

Specifications

FAQ and troubleshooting

• Q1, Cracking or popping sound or Static sound when optical connection:

  • Answer: press the home (or menu) on the TV remote, go to TV setting ›audio (sound) -> TV speaker–select external speaker(turn off TV speaker), save the setting, then back to audio(sound setting)—select expert setting—digital audio output(or optical output)-select PCM(some TV called SPDIF or optical), Save the setting, then try again. More detail refer page 6, or your TV manual.

• Q2, Cracking noise or static sound when see a video from Youtube, Netflix, HBO, Amazon Prime or other streaming video APPs:

  • Answer: please disable the Dolby and DTS on your APPs or TVs, if you do not know how to set, please contact the APPs support or us for help.

• Q3, Sound is not synced with the picture.

  • Answer: please press the menu or home button on the TV remote go to the TV setting-›sound(audio)-select sound (audio) delay—adjust the delay time to try, this will fix the issue.

• Q4, Why soundbar is very weak?

  • Answer: Please kindly note the max volume of this soundbar is very loud, there are several Answers that you can try to fix the problem:
  1. Please make sure your sound source volume is high, if the sound source is in low volume, you will not get loud sound, so we suggest you adjust the TV and APPs volume to max.
  2. Adjust the soundbar volume to max to test again
  3. Please kindly use your phone to connect the soundbar through to play the music to test the sound.
  4. Please unplug and plug the adapter to restart the soundbar to test again.
  5. Disable the hearing protection setting on your devices such as phone, tablet, TV.

• Q5, Why sound quality is poor?

  • Answer: please kindly note the soundbar we offered is entry-level, for small rooms not for Audiophile, can not be compared to the soundbar priced at $200 or above. If the sound quality is very poor, you may receive the detective unit, please contact us, we will guide you to update the firmware to fix the issue.

• Q6, May I connect the sound bar to Amazon Echo?

  • Answer: Sure, you can connect this soundbar to your Amazon Echo through BT connection, please scan below QR code to find the connect method
    Kindly note: except the BT, you also can use the aux cable to connect the soundbar to your Amazon echo dot. (Please note BT connection only for music play, the soundbar DOES NOT have the built-in Alexa)

• Q7, soundbar can not turn on.

  • Answer: Please use the attached adapter to connect the speaker to the socket,wait about 3 seconds, the speaker indicator will show white light, press the on/off button on the remote control to turn on the speaker. If the speaker does not show white light, please check whether the adapter indicator light can be on. If not, it means that the adapter is dead, please contact us and we will replace a new adapter for you free of charge.

• Q8, May I connect the soundbar to a headphones?

  • Answer: please note both headphones and soundbar only can receive the audio signal, can not output, so you can not connect the soundbar to headphones to play musIc.

• How can I use the TV remote, universal remote, or cable remote to control the volume?

  • Answer: Sound bar can not support TV remote or universal remote, but here is a solution: please kindly use aux cable connect the sound bar to your TV headphones jack or RCA jack, then you can use your TV remote or cable remote to control the volume, more detail, please refer the AUX cable connection guide on the quick start card, please kindly try.
    Kindly note: when you contact us, please kindly provide your Amazon order ID, model number, address, and exact issue with us.

For more information, please follow us:
Web: www.wohomeshop.com
Email: support@wohomeshop.com

NOTE: One year warranty, 45 days money back guarantee, lifetime technical support, 100% satisfaction service, please feel free to contact us for any questions.

Scan the code to vIsIt our youtube channel

Scan the code to find soundbar setup instructions accord- ing to your TV brand

Scan the code and fill in the contact form to contact us quickly for any issues

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>