STREAMLIGHT Vantage II Helmet Mounted LED Flashlight Instruction Manual
- October 30, 2023
- StreamLight
Table of Contents
- LED SAFETY
- BATTERY SAFETY
- MOUNTING: FIRE HELMET
- MOUNTING: INDUSTRIAL MOUNT
- MOUNTING: GALLET HELMET
- MOUNTING: MSA HELMET
- BATTERY INSTALLATION/REMOVAL
- SWITCH OPERATION
- TAIL LIGHT ENABLE/DISABLE/FLASH
- MAINTENANCE
- STREAMLIGHT LIMITED LIFETIME WARRANTY
- SERVICE OPTIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
STREAMLIGHT Vantage II Helmet Mounted LED Flashlight
Thank you for selecting the Vantage® II Series helmet-mounted LED flashlight.
As with any fine tool, reasonable care and maintenance of this product will
provide years of dependable service.
Please read this manual before using your flashlight. It includes important
safety and operating instructions.
SAVE THESE INSTRUCTIONS. This guide contains important safety and operating
instructions for your Vantage® II series flashlight.
LED SAFETY
LED RADIATION (RG-2). DO NOT STARE INTO BEAM. MAY BE HARMFUL TO EYES. PER IEC 62471 ED 1.0:2006-07.
BATTERY SAFETY
EXPLOSION RISK, BURN, AND FIRE HAZARD. DO NOT DISASSEMBLE, CRUSH, SHORT CIRCUIT, HEAT ABOVE 212°F (100°C), OR DISCARD IN FIRE. DO NOT RECHARGE BATTERY. KEEP AWAY FROM CHILDREN. BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
USE ONLY: Streamlight, Panasonic or Sanyo size CR123A; Duracell 123A, or Energizer 123A.
MOUNTING: FIRE HELMET
- Select the desired position above or below the helmet brim.
- Loosen the clamp locking screw.
- Slide the clamp assembly over the brim of the helmet and rotate it to the desired position.
- Tighten the locking screw until the Vantage® II is securely attached to the helmet using the hex key provided.
MOUNTING: INDUSTRIAL MOUNT
- Insert locking tab into hard hat.
- Push locating tab until assembly securely clicks.
- To remove, depress tab and pull light from helmet.
MOUNTING: GALLET HELMET
- Insert clamp in helmet slot until securely clicks
- To remove, depress lock tab on helmet and slide rearwards.
MOUNTING: MSA HELMET
- This light can be mounted on top of the brim (either side of the helmet).
- Remove the chin strap screws, plate, and two nuts on the top of the helmet brim.
- Rotate the adapter plate and wedge spacer such that the arrow is pointing forward and the thickest end of the wedge spacer is towards the back. This will maintain a slight downward aim to illuminate the ground ahead.
- Slide the clamp assembly over the brim of the helmet and rotate it to the desired position.
- Tighten the chin strap screws until the Vantage® II is securely attached to the helmet.
NOTE: For all helmet mounts, it is possible to remove mount assembly from the “dove tail” slot by unscrewing the small set screw on the dove tail plate. (Hex key not included)
BATTERY INSTALLATION/REMOVAL
At the end of battery life, the unit may appear intermittent or non- functional. Replacing the battery will restore normal operation.
- Unscrew and remove the facecap assembly from the body of the Vantage® II. Remove the exhausted battery from the flashlight body.
- Insert a fresh CR123A battery, positive end first, into the body of the Vantage® II. Battery polarity is indicated on the side of the Vantage® II body.
- Place the facecap assembly onto the Vantage® II body. Fully tighten the facecap assembly to ensure that the battery makes complete contact with the internal electrical contacts.
- For “safe” mode, loosen the facecap approximately ¼ turn to the detent. This will disconnect the battery for safe storage and the light will not operate if the switch is depressed.
SWITCH OPERATION
Press switch button to turn on light in Low mode.
Double tap switch button within 1.5 seconds for High mode.
- NOTE: The Vantage® II will not operate if the facecap is in “safe” mode.
TAIL LIGHT ENABLE/DISABLE/FLASH
The Vantage® II ships from the factory with tail lights set to steady mode. To change the tail light mode, press and hold the switch button for 5 seconds. After the initial 5 seconds, the mode will cycle every 2 seconds. Release the switch button when the desired mode it reached. Modes are “steady,” “tail lights off,” and “tail lights flash.”
MAINTENANCE
Use a soft cloth and mild detergent to clean the glass LED lens and keep it
free of dirt and grime.
Note: Always avoid aggressive cleaning solutions as they may damage the
Vantage® II.
PRODUCT USE
Streamlight flashlights are intended for use as high intensity, heavy duty, and portable light sources. Use of Streamlight flashlights for any purpose other than as light sources is specifically discouraged by the manufacturer. Streamlight specifically disclaims liability for other than recommended use.
Be sure to use only genuine Streamlight replacement parts to assure product safety. Substitution may invalidate the product approval. Do not try to repair the unit yourself. Send to a qualified service facility or return it to the factory.
STREAMLIGHT LIMITED LIFETIME WARRANTY
Streamlight warrants this product to be free of defects for a lifetime of use except for batteries and bulbs, abuse and normal wear. We will repair, replace or refund the purchase price of this product should we determine it to be defective. This limited lifetime warranty also excludes rechargeable batteries, chargers, switches and electronics which have a 2 year warranty with proof of purchase. THIS IS THE ONLY WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARE EXPRESSLY DISCLAIMED EXCEPT WHERE SUCH LIMITATION IS PROHIBITED BY LAW. You may have other specific legal rights which vary by jurisdiction.
Go to www.streamlight.com/support for a complete copy of the warranty, and information on product registration and the location of authorized service centers. Retain your receipt for proof of purchase.
SERVICE OPTIONS
The Vantage® II contains few or no user-serviceable parts.
For service options, go to
www.streamlight.com/support/service
and complete the Online Service Request for factory service or to find the
location of an authorized Streamlight repair center near you.
Or contact: Customer Service STREAMLIGHT, INC. 30 Eagleville Road
Suite 100
Eagleville, PA U.S.A. 19403-3996
Phone: (800) 523-7488
Toll-Free / +1 (610) 631-0600
Fax: (800) 220-7007 / +1 (610) 631-0712
www.streamlight.com
30 Eagleville Road
Eagleville, PA 19403
Phone: (800) 523-7488
997791 Rev. B 1/23
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>