Akuvox R20A IP Door Phone User Guide

June 6, 2024
Akuvox

Smart intercom
R20A
Wall-mounting Installation
Quick guide

Unpacking

Before you be using the device, please check the version you obtained and ensure that the following items are included in the shipped box:
Universal Accessories:

| R20A x 1| | Cable locking plate x 1
---|---|---|---
| Rope x 1| |  M2.5×6 screw x 6
| Diode x 2| | Rubber Plug x 3 (S, M,L )
| Back cover x 1| |

Wall-mounting Accessories :

| ST4x20 screw x 4| | Plastic Wall Anchor x 4
---|---|---|---
| Allen Wrench x 1| | Allen screw x 2
| Wall-mounting bracket x 1| | Wall-mounting screw x 4
| M4x30 screw x 2| |

Product Overview

Installation Environment

Indoor and outdoor installation are supported:
If installing the device outdoors, please don’t place the device under direct sunlight, it will bring a bad effect or be broken with the high temperature.
If installing the device indoors, please keep the device at least 2 meters away from light, and at least 3 meters away from the window and door.

Installation

step 1: Wall-mounting bracket Installation
1. With embedded one-gang junction box(86×86 mm or 2×3 inches in size) in the wall.

Fix the wall-mounting bracket on the embedded box with two M4x30 screws.
Fix the wall-mounting bracket on the embedded box with two M4x30 screws.
Remove the bracket to drill (5 mm drill bit required) the two marked fixing holes on the wall with a depth of 25 mm. Then insert two plastic wall anchors.

Fix the wall-mounting bracket with two M4x30 screws.
Finish the wall-mounting bracket installation.
Tighten the wall-mounting bracket on the wall and junction box using two ST4x20 screws and two M4x30 screws.

Without 86 embedded boxes in the wall

Akuvox R20A IP Door Phone - box

Mark the four holes of the wall-mounting bracket on the wall for the screws.
Use a hand drill with a 5mm diameter bit to make four 25mm depth holes in the marked positions.
Insert four plastic wall anchors into the holes.
Fix the wall-mounting bracket with four ST4x20 screws.

Step 2:Back cover Installation

For convenient wiring, hang
R20A on the wall-mounting bracket with rope.
Make cables go through the back cover, connecting to the corresponding interfaces of the mainboard. back of R20A.

Akuvox R20A IP Door Phone - Back cover

After successful installation, Insert the four wall-mounting screws on
Select a suitable size rubber plug to check the stability of the device. the device into the corresponding holes to push all the cables into the back cover.Fix cable locking plate to the back cover with two M2.5×6 screws. on the wall-mounting bracket, and then press down to slide the wall-mounting screws into the groove. Then use the
Allen Wrench to tighten the device with two Allen screws.

Akuvox R20A IP Door Phone - BEACK COVER 2

Application Network topology

Akuvox R20A IP Door Phone - NETWORK TOPOLOGY

Device Wiring

Device Wiring Warning:
When you connect a device containing a coil, such as a relay or an electromagnetic lock, it is necessary to protect the intercom against voltage peak while switching off the induction load. For this way of protection, we recommend a diode 1 A / 200 V (included in the accessories) connected antiparallel to the device.

Akuvox R20A IP Door Phone - Device Wiring2

IP Announcement:

  1. While R20A starts up normally, hold the call button for several seconds after the Status LED turns blue, voice system will enter IP announcement mode.
  2. In announcement mode, the IP address will be announced periodically.
  3. Press the Call Button again to quit the announcement mode.
  4. In announcement mode, the phone announces “IP 0.0.0.0” if no IP address is gained.

Configuration:

  1. Access the Web UI: Input the IP address into a web browser to configure the phone.
  2. Account Registration: On web UI, go to the path: Account - > Basic page to register an account and fill in the account information. ( Please refer to admin guide for more  information)
  3. Configure the Push Button: On web UI, go to the path: Intercom -> Basic -> Push Button to configure the call number.
  4. Configure the code to open the relay: On web UI, go to the path: Intercom - > Relay -> Relay ID/DTMF and choose the DTMF code number in the corresponding area.

Operation

Make a call:

  1. Press the call button to call the indoor SIP Phone.
  2. During the talk, the called party can press a pre-configured code number to unlock the door.

Receive a call:
R20A supports Auto Answer by default. The incoming call will be answered automatically.

Indicators

light on
light off

Name

| Status| |

Description

---|---|---|---
Status indicator| Blue| | Normal status
| Calling
Red| | Restarting
| Network is unavail
Green| | Initialing/Talking oo call
| Receiving a call
Red/Blue| | Firmware upgrading

Note: For more LED settings, please refer to R20 WebUI: Intercom -> LED Setting.

Notice Information:
Akuvox R20A firmware contains third-party open-source software under the terms of the GNU General Public
License(GPL). Akuvox is committed to meeting the requirements of the GNU General Public License (GPL) and will make all required source code available.
The source code of software under the terms of GNU GPL can be downloaded online: http://www.akuvox.com/gpl.
Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without notice, any update to this document can be viewed on Akuvox’s s website: http://www.akuvox.com © Copyright 2021 Akuvox Ltd. All rights reserved.

AKUVOX (XIAMEN) NETWORKS CO., LTD.
ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK II, XIAMEN 361009, CHINA www.akuvox.com

http://www.akuvox.com/

YS20000047

Documents / Resources

| Akuvox R20A IP Door Phone [pdf] User Guide
R20A, IP Door Phone, R20A IP Door Phone
---|---
| Akuvox R20A IP Door Phone [pdf] User Manual
R20A IP Door Phone, R20A, IP Door Phone, Door Phone, Phone

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals