rizoma Vespa GTS 300 License Plate Support Kit User Manual
- June 12, 2024
- rizoma
Table of Contents
**rizoma Vespa GTS 300 License Plate Support Kit User Manual
**
Before you start
We are pleased to welcome you into the world of RIZOMA, and we congratulate you for your excellent choice. Please carefully follow the instructions in this guide, which will allow you to mount and use the product correctly and enjoy all the features it has. For your protection and safety, RIZOMA expressly recommends that you have the installation of the product performed by skilled personnel. Improper installation, repair or maintenance, can cause accidents. Keep this user guide as a reference for the future. RIZOMA accepts no liability for any damage, of any kind, which may be caused, directly or indirectly, to persons or things as a result of incorrect assembly or failure to observe all the assembly instructions. We also invite you to comply with the provisions of the Highway Code and Traffic rules and/or to additional regulations in force in your Country
Attention:
This component comes assembled for shipping purposes only. Tighten all
fasteners to appropriate torque specifications before riding.
Descriptions preceded by this symbol contain information, instructions, or procedures, which, if not followed, may result in death or serious injury.
- Carefully read, understand and follow these instructions, they are an essential part of the product. If you have any doubt whatsoever regarding the installation or use of your RIZOMA product, please see your authorized RIZOMA dealer for assistance (on www.rizoma.com).
- For correct installation, all tightening has to be done after the correct positioning of the accessories without restricting the moving parts, to not compromise the correct functioning of the product.
- After installing any Rizoma product, please check that all related components of the motorbike function e.g. brakes, throttle, clutch, lights and steering. We strongly suggest to repeat these checks periodically, especially after long trips or prolonged periods of not using the bike.
Your RIZOMA products require regular inspection and maintenance. The more you ride the more often you must inspect your RIZOMA products. If your products are leaking, bent, deformed, cracked, chipped or worn, no matter how slight, immediately have a RIZOMA dealer inspect the products before you ride again. In any case never try to repair or modify the Rizoma products or their components, always replace with Rizoma original components.
Rizoma products may not be compatible with your motorcycle or with other aftermarket equipment installed before. For your safety Rizoma suggests to always contact your RIZOMA dealer
To comply with the TÜV and European Norm in force, the installation of the license plate must be carried out as the enclosed instructions. Consult the website www.rizoma.com, in FOX license plate support section click “DOWNLOAD” to download the PDF document approval ABE.
Before you start mounting the product please check the completeness of the kit
on the part list. The difficulty level and the time of assemblage shown do not
include the removal of OEM components. Warning: Make sure that your motorbike
is standing firmly before you start work, as a fall may lead to damage to the
motorbike or injury to you or others.
WARNING: TO CLEAN YOUR PRODUCT DON’T USE DETERGENT, AGGRESSIVE PRODUCTS OR
ABRASIVE SPONGE THAT CAN DAMAGE OR SCRATCH YOUR PRODUCT, BUT USE ONLY NEUTRAL
DETERGENT WITH COLD WATER
Improper installation could damage the electrical system of the motorcycle and cause a fire, resulting in personal injury or death. Electrical shock hazard. Disconnect the battery before starting to install turn license plate bracket or rear light or the turn signals. The pins must always be isolated and respect the polarity in the connections. The warrantee is not valid for any electric wires cutting or any product modify or tampering
2-3-4 mm
10 mm
DIFFICULTY LEVEL
DIFFICULTY LEVEL
INSTALL REAR LIGHT SPACER
**Step 1
**
Warning: where required by current legislation the spacer must by installed
Angle Of geometric Visibility (Dihedral with horizontal EDQE)
Angle Of geometric Visibility ( Dihedral with perceptibly Vertical** EDQE)**
INSTALL PLATE FOR MEDIUM/LARGE LICENSE PLATE
Step 6
INSTALL COVER
Warning: place the rizoma cover by inserting the 2 guide in the holes
on the fairing . connect rear light before fixing the license plate
Step 6
Step 7
Step 8
CONNECTIONS
- REAR LIGHT ELECTRICAL WIRES COLOURS: –
- BLACK WIRE= GROUND; –
- RED WIRE= STOP LIGHT; –
- YELLOW WIRE= POSITION LIGHT AND LICENSE PLATE LIGHT
RIZOMA reserves the right, in its sole discretion, to make changes to the product and this information at any time and without prior notice. Although many catalogs and advertisements depict riders engaged in extreme or stunt riding, this activity is extremely dangerous, increases the risk of an accident, and increases the severity of any injury.
The action depicted is performed by professionals under strictly controlled riding conditions. Only you know the limits of your riding ability and only you can control the conditions under which you ride. By and in consideration for his/her purchase and use of the RIZOMA product, the user expressly recognizes and agrees that in the event of any claim arising out of the use of this RIZOMA product, whether such claim is based in contract, warranty, tort (personal injury or wrongful death) or otherwise, the laws of the Republic of Italy shall apply and jurisdiction and venue for any such action shall be in the Courts of Busto Arsizio, Italy.
All riders are strongly urged to take a motorcycle rider safety clinic. Always wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a full face helmet), that has been approved by ANSI , SNELL, CE, or any other relevant authority, and any other safety equipment necessary for your riding style, such as full finger gloves, boots, and body armor.
Be sure to read and follow all the instructions and warnings that originally accompanied your motorcycle, as well as the literature that accompanied any other component parts installed on your motorcycle.
Be sure that your tires are inflated to the correct pressure and that there is no damage whatsoever in the tread or sidewall of the tire.
Some of our products may not be approved for road circulation in the countries where homologation is required. Thus RIZOMA® srl declines any responsibility for a different use of its products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>