JBC AT420 Adjustable Thermal Tweezers Instruction Manual
- June 12, 2024
- JBC
Table of Contents
www.jbctools.com
INSTRUCTION MANUAL
AT420
Adjustable Thermal Tweezers
This manual corresponds to the following reference:
AT420-A
Packing list
The following items should be included:
Adjustable Thermal Tweezers ……………1 unit
Screwdriver…………………………………………..1unit
Ref. 0023074www.jbctools.com
Manual …………………………………………………1 unit
Ref. 0030510
Features
*not included, sold separately
Changing Cartridges
- Unlocking Unlock the fixing screws.
- Removing Place the cartridges in the extractor (1) and pull the tweezers to remove them (2).
- Positioning Use the vertical grooves to position the cartridges and place the tweezers onto the cartridges.
- Inserting Use the vertical grooves to position the cartridges and place the tweezers onto the cartridges.
Press the cartridges against the extractor and make sure that the cartridge is inserted up to the mark*.
-
Important
It is essential to insert the cartridges as far as the mark for a proper connection.
- Rotational Cartridge Alignment and Locking Slightly turn the wheels to align the cartridges as required (1). Then lock the cartridge fixing screws* (2).
- Vertical Cartridge Alignment
The wheel allows the tips to be adjusted so that they are aligned when the tweezers are closed.
Once the alignment has been made, it is imperative to fix the cartridges by tightening the fixin screws. It takes a single turn of the screw to lock it in place.
Tweezers Positioning
The tweezers position in the stand is shown in the image (1).
Note:
When using the customized cartridges like ref.
C420283 and ref. C420286, place the tweezers vertically, as shown in the image
(2).
Compatible Cartridges
Adjustable Thermal Tweezers AT420 works with C420 cartridges. Find the model
that best suits your soldering needs at
www.jbctools.com.
Wiper
The integrated wiper offers different ways to clean the cartridge tips.
Tapping
Tap gently to remove excess solder.
Wiping
Use the slots to remove the remaining particles.
Sponge
The softest cleaning method.
Keep the sponge damp with distilled water when working to void tip wear.
Wiper and Brass Wool Replacement
The wiper and brass wool can easily be removed for cleaning or replacement
when they are worn.
Lift the wiper at its front edge.
Remove the wiper by pulling it out.
Replace the brass wool with a new one when it is worn out.
Place the wiper back or replace it if desired.
Safety
**** It is imperative to follow safety guidelines to prevent electric shock,
injury, fire or explosion.
– Do not use the device for any purpose other than soldering or rework.
Incorrect use may cause a fire.
– The power cord must be plugged into approved bases. Be sure that it is
properly grounded before use. When unplugging it, hold the plug, not the wire.
– Do not work on electrically live parts.
– The tool should be placed in the stand when not in use in order to activate
the sleep mode. The soldering tip or nozzle, the metal part of the tool and
the stand may still be hot even when the station is turned off. Handle with
care, including when adjusting the stand position.
– Do not leave the appliance unattended when it is on.
– Do not cover the ventilation grills. Heat can cause inflammable products to
ignite.
– Avoid flux coming into contact with skin or eyes to prevent irritation.
– Be careful with the fumes produced when soldering.
– Keep your workplace clean and tidy. Wear appropriate protection glasses and
gloves when working to avoid personal harm.
– Utmost care must be taken with liquid tin waste which can cause burns.
– This can be used by children over the age of eight and also persons with
reduced physical, sensory or mental capabilities or lack of experience
provided that they have been given adequate supervision or instruction
concerning the use of the appliance and understand the hazards involved.
Children must not play with the appliance.
– Maintenance must not be carried out by children unless supervised.
Specifications
AT420
Adjustable Thermal Tweezers Ref.: AT420-A
– Max. Power per Cartridge:
– Cable Length:
– Total Net Weight:
– Package Dimensi ons/Weight: (L x W x H)
Complies with CE standard ESD Safe| 80 W
1.3 m / 51.2 in
126 g / 0.278 lb
277 x 73 x 50 mm / 194 g
10.91 x 2.87 x 1.97 in / 0.428 lb
---|---
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/within 30 days of purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility. a manuales – color gris
www.jbctools.com
0030510-221222
Documents / Resources
| JBC
AT420 Adjustable Thermal
Tweezers
[pdf] Instruction Manual
AT420 Adjustable Thermal Tweezers, AT420, Adjustable Thermal Tweezers, Thermal
Tweezers, Tweezers
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>