R3 Mini DV User Manual

R3 Mini DV User Manual

1. Before Using

► Boot up the camera without TF card, the camera will shut-down automatically after the red and blue indicator flashing for 5 seconds at the same time.

► Boot up the camera without any working mode, the camera will shut-down automatically after one minute.

1.1 Product Structure

1. Mini USB

2. TF Card Slot

3. Notch for Attachment

4. Camera port

5. Indicator Light

6. On/Off Button
7. M Button

8. Infrared IR Night Vision Lamps

2. Basic Instructions

2.1 How to charge

The camera built-in rechargeable lithium battery, please charge it before the first using.

Methods:

1. Connect the camera to computer，charge it with USB cable;

2. Charging while recording: Connect to external USB 5V charger or mobile power supplement;

• The red indicator light is on and flashing normally when you charge the camera. When the red indicator light keeps on but stops flashing means charging is completed.( Please charge for more than 30 minutes to make sure the battery is fully charged.)

Note:  When the battery power is low, the red and blue indicator lights flash at the same time for about 5 seconds, the camera will shut-down automatically, enter into the protection state (The recording file will save automatically), the camera should be charged under this condition.

2.2 Charging While Recording

Insert TF card, connect USB 5V charger or mobile power supplement with USB cable, start recording videos while charging the camera.
Click any button to stop recording. Or the camera will keep recording until out of battery.

2.3 Reset

If the machine crashes, the button can not be used normally, you can press the «Power» key and the «M» key to reset the machine, then it can be used normally.

2.4 Power Off

If you want to shut down the camera under the video recording, photo taking, motion detection mode. Press «On/Off» button for about 6 seconds to shutdown the camera. ( The indicator light is off.) When the camera is under standby mode, the camera will shut-down automatically after one minute without any working mode.

2.5 Time Setting

The camera will automatically create a TXT text document in the TF card directory. ( As the pic ) Shutdown the camera, connect the camera to computer with USB cable, open TIMEREST.txt document. Edit and save the time you need in the document. ( Such as “ 20160804174726 Y ”) Boot up the camera to shoot videos, the video will show the time watermark you save in the txt document. You can use the same method if you don’t need time watermark.

For example:

20150608192526 Y ( Have time watermark)

20150608192526 N ( Don’t have time watermark)

Notice:

1. Be sure to insert the T-flash (Micro SD) card into the product. If the card have not TF/SD card inside, the camera can not be used normally when the red and blue indicator light flash at the same time.

2. Please keep the lens at the distance of 50cm or more in the environment with sufficient lighting. This way makes the images and videos stable with natural color, and scenery is clear.

2.6 Connect to a computer

The camera can be directly connected to the computer under boot up, standby, or shutdown mode. It can be used as normal U disk and you can copy/paste/delete the file as usually do.

Connect the camera to the computer, after a few seconds the computer will pop up the removable disk logo, when the blue indicator light is on, means the computer can identify the USB device and carry out data transmission, the red light is on means the camera is charging, the red light flashes for a long time means the camera is fully charged.

Note:

1. After the unit is connected to the computer, if the computer does not recognize it, or if the removable disk is not ejected after 30 seconds, please reset it and try again.

2. It is recommended to use the TF card reader to read the video file directly to play, if you directly use the USB connection to save the machine built-in memory in the video file, the transmission can not keep up because of the data may be too large and resulting in playback is not smooth.

3. Mode Instructions

3.1 Recording Mode

1. Boot up the camera, enter the standby mode. (The blue indicator light is on.)

2. Click the power button.( The blue indicator light is flashing slowly.) Start recording 1080P HD videos.

3. The video will safe video as segmented video every 5 minutes. The video will be loop covered if there is no enough storage.

4. Click the power button again to stop recording, back to standby mode.

5. Push the power button for a long time under the recording mode will shut down the camera. Recording file will be preserved automatically.

3.2 Recording Infrared Mode

1. Boot up the camera, enter the standby mode. (The blue indicator light is on.)

2. Push the power button. (The blue indicator light is flashing slowly.) Start recording 1080P HD videos.

3. Click the «M» button under the RECORDING MODE to start infrared mode. (The blue indicator light is flashing quickly.)

4. Click the «M» button again, back to normal recording mode.( The blue indicator light is flashing slowly.)

3.3 Photographs-taking Mode

1. Boot up the camera, enter the standby mode. (The blue indicator light is on.)

2. Click the «M» button to start taking photographs. (The red and blue indicator light is opened at the same time.)

3. Every click on the «Power» button is taking a pic. (The red indicator light flashes with each clicking.)

4. Photos will be preserved automatically as 12M (4032*3024)

5. Push the «Power» button for a long time will shut down the camera.

3.4 Motion Detection Mode

1. Insert mini TF card, then push power button to make sure the camera is on the standby mode. (The blue indicator light is on.)

2. Push the «M» button for 3 seconds, to get the motion detection working. (The red indicator light is on and flashing slowly.)

3. Once the camera detect the object is moving, the camera starts recording. (The red indicator light is on and flashing quickly.) If there is no object moving the camera will stop recording. (Time the red indicator light is on and flashing slowly.)

3.5 Motion Detection Infrared Mode

1. Click «M» button under the motion detection mode to start infrared mode. (The red and the blue light alternately flash.)

2. Click the «M» button again, back to motion detection standby mode. (The red indicator light flashes slowly.)

3.6 TV-OUT Mode

Connect to TV with the USB TV cable, boot up TV you can be see images through the TV screen, you can take pictures, video, open motion detection mode in the mean time.

4. Parameters

4.1 Relevant Parameters

• Video Format: AVI
• Video Code: M-JPEG
• Resolution: 1920×1080P
• Frame Rate: 30fps
• Proportion 16:9
• Resolution: 12M (4032×3024)
• Picture Format: JPG
• Motion Detection: Support
• Battery type: Built-in high-capacity lithium polymer
• Battery capacity: 450mAh
• Working time: 2.5 hours
• Voltage: DC-5V
• Memory: Max up to 32GB
• Speed: High speed USB2.0
• Port: Mini 8pin USB
• Support System: Windows me/2000/XP/2003/Vista; Mac Os; Linux
• Playing Software: Default Software

4.2 Notes

Each time you use the battery and then charge, about to charge about 2-3 hours to fill, the indicator light is filled as much as possible after 30 minutes to ensure that the fully charged.

Because this product is the real HD DV, the product power consumption is larger than the Purple, the shell material using zinc alloy parts, and the use of the product may cause hot, it’s normal phenomenon, please do not worry. The product has come through a long period of time tests. There can not be any product quality problems.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>