RAIN HARVESTING HW1902 Sliding Gate Valves Plastic Paddle User Guide
- June 12, 2024
- Rain Harvesting
Table of Contents
Sliding Gate Valves
Plastic Paddle Installation and Specification Guide
PRODUCT DETAILS
This simple to use sliding gate valve with a plastic paddle allows you to easily drain charged lines.
Code | Size | Country |
---|---|---|
HW1902 | 3″ | USA |
HW5902 | 68mm | UK |
HW3902 | 80mm | SA |
HW0902 | 90mm | AU/Other Countries |
HW0921 | 100m |
Installation
WHAT’S IN THE BOX?
- Sliding Gate Valve
TOOLS/MATERIALS YOU MAY REQUIRE
- Marker Pen
- Tape Measure
- Saw
- Solvent weld glue
- Priming fluid
SLIDING GATE VALVES – PLASTIC PADDLE
- – Select your desired installation point. The Sliding Gate Valve can be installed in the vertical or horizontal position.
- – Measure and remove a 35mm section of pipe at your desired installation point. Ensure all cut edges are clean and smooth.
- – Use priming fluid to clean inside the sockets of the Sliding Gate Valve and outside of the pipes you will be gluing the valve to.
- – Apply solvent weld glue first to inside the sockets of the Sliding Gate Valve and then to the outside of the pipes, bring together and ensure pipes are inserted fully into the sockets of the Sliding Gate Valve.
Hold for a minimum of 60 seconds or until secure.
Product Specifications
Dimensions & Pipe Fittings
COUNTRY | CODE | A | B | C | D | E |
---|---|---|---|---|---|---|
USA | HW1902 | 3″ SCH40 F | 5.09″ | 4.37″ | 14.17″ | 10.20″ |
UK | HW5902 | 68 F | 135 | 111 | 360 | 259 |
SA | HW3902 | 80 F | 140 | 111 | 360 | 259 |
AU/Other
Countries| HW0902| 90 F| 91| 111| 360| 259
HW0921| 100 F| 136| 170| 460| 331
All dimensions are in mm unless otherwise stated.
Fitting guide:
F = Female / Socket Fitting
M = Male / Spigot Fitting (Pipe size)
IP = In-Pipe Fitting
SPECIFICATIONS
Pressure Ratings| Size| Paddle Type| Max Pressure (kPa)|
Mid Flow Max Crossing Pressure (kPa)
---|---|---|---|---
HW1902| 3″| Plastic Paddle| 210| 5
HW5902| 68mm| Plastic Paddle| 210| 5
HW3902| 80mm| Plastic Paddle| 210| 5
HW0902| 90mm| Plastic Paddle| 210| 5
HW0921| 00mm DWV| Plastic Paddle| 210| 5
A common misconception about collecting rainwater is that all you need is a
roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on
to deliver the volume – or quality – of water that you require. That is where
we can help.
With some thought, your rain harvesting system can provide you with cleaner
water and lots of it. Whether you’re completely reliant on tank water or
wanting to keep the garden green, our simple steps will help you achieve your
goal.
The Rain Harvesting approach to rainwater collection involves using tested and
proven products to make quality rainwater available for use in and around your
property. You don’t need much to get started and you will be surprised how
easy it is to get the most out of your rainwater system.
DISCLAIMER This product specification is not a complete guide to product usage. Further information is available from Rain Harvesting Pty Ltd and from the Installation and Operating Instructions. This specification sheet must be read in conjunction with the Installation and Operating Instructions and all applicable statutory requirement. Product specifications may change without notice. © Rain Harvesting Pty Ltd
For more information or to find out
how we can help, just give us a call on
+61 7 3248 9600
Or visit our website at
rainharvesting.com
References
- Cleaner Water. More of it. | Rain Harvesting by BMCo US
- Supported by Rain Harvesting | Blue Mountain Co - Rain Harvesting