Kywoo3D Tycoon IDEX FDM 3D Printer User Manual

Kywoo3D Tycoon IDEX FDM 3D Printer

Dear Customers,

Thank you for choosing our products. For a better user experience, please read the instructions carefully before operating the printer.
Our team is always be ready to provide you with the best customer service. Please contact us via the email address provided at the end of the manual if you encounter any problem with the printer. You can also learn how to use the printer in the following ways:

• View the instructions and videos on the supplied TF card;
• Visit our officia I website www.kywoo3d.com to find relevant firmware/ ha rd ware information, contact details and operation and maintenance instructions.

NOTES

+ 1. After unboxing, please check whether the machine is damaged, bent, or scratched, and check the parts against your order. If you have any questions, please promptly contact our after-sales service via the Kywoo 3D official website or the email address provided on the manual.

• Do not use the printer for anything other than described herein in order to avoid personal injury or property damage.

• 3. Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
  + 4. Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.

• 5. Please use the recommended filaments to avoid the blockage of the extruder and damage to the machine.
  + 6. Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.

• 7. Do not touch the nozzle or printing surface during operation as they may be hot. Keep hands away from machine while in use to avoid burns or personal injury.
  + 8. Do not wear gloves or loose clothing when operating the printer. Such clothes may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.

• 9. After printing, use the provided tools to clean up any filament on the nozzle while it’s still hot. Do not touch the nozzle directly with your hands.
  + 10. Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame, guide rails and wheels. Use glass cleaner or isopropyl alcohol to clean the print surface before every print for consistent resuIts.
  + 11. Children under 10 years of age should not use the printer without supervision.

• 12. This machine is equipped with a security protection mechanism. Do not manually move the nozzle or printing platform while booting up, otherwise the device will automatically power off for safety. + 13. Users shall comply with related national and regional laws, regulations and ethical codes where the equipment or prints produced by it are used, and users of our product shall not use aforesaid products to print any end-use products, objects, parts or components or any other physical prints that violate the national or regional laws, regulations and ethical codes where herein referred product and produced prints by it is located.

Introduction

Parts List

• Body
  

• Base Frame
  

• Power Cord
  

• Filament Holder
  

• Tempered Glass
  

• 200g Filament
  

• Spade

• Card Reader

• SD Card
  

• Open-end Wrench
  

• Cable Tie

• Limit Switch

• 0.4mm Nozzle

• USB Cable
  

• Diagonal Pliers

• PTFETube

• Belt Tension Spring
  

• MSX25mmScrew

• Nozzle Cleaner
  

• Slotted Screwdriver
  

Parameters

Output: 24V 17A Max
Total Power| 400W
Bed Temp| <ll0’C
Nozzle Temp| ,(260′(
Filament Detector| Yes
Calibration| Auto Leveling
Recommended Printing Speed| 50-S0mm/s
Net Weight| 16kg
Auto Shut-down Function| Standard
Supported Languages|

1. English 2
2. Spanish; 3
3. French;
4. Italian;
5. German

Assemble the 3D Printer

Install the Base

1. Take the printer out from the package box and pull the Z-axis timing belt slowly to make the Z-axis raise 15cm around, as shown in picture 1.

2. Slide the base through the gantry frame from the front of the body (please make sure the Y-axis motor is at the rear of the body). Next fix the body and the base together using four M5*25mm screws, as shown in picture 2 and 3.

3. Connect the Y-axis motor wire and end-stop switch wire, as in pie 4and 5.
   
   

4. Then connect the hotbed heating wire and thermistor wire, like in picture 6.
   
   

5. As shown in picture 7, fix the filament holder on the top profile, then tighten the T-nuts of the holder.

Install the Tempered Glass Platform and Connect the Power Cord

1. As shown in picture 1, place the glass on the silver-white platform and clamp it with the Hotbed clips.
   

2. Select the proper input voltage to match your local mains (115/230V), 230V by default. Damage may occur if the voltage is set incorrectly.
   

3. Connect the power cord, first turn the power switch to “I”, then press and hold the reset switch for 1-3 seconds, until the display lights up, indicating that the printer has started. Do not disconnect the power cord while the printer is working.

Screen Interface

Use the 3D Printer

Home and Auto-level the Heated Bed

1. Turn on the 3D printer, click the coordinate box, click” ” and wait for all the axes homed.
2. Click “ ” to auto-level the printer. (Note: the printer needs to be auto-leveled whenever the nozzle or the printing bed is exchanged.)
   
   

Preheat

Back to the home page. Click the “nozzle” and “hotbed” icons above, and adjust the preheating temperature by dragging the slider. For your reference: the preheating temperatures of PLA filament are 200°C for nozzle, SS°C for hotbed.

Load the Filament

When the hotbed and the nozzles reach their set temperatures, lift the Z-axis by 5cm, and pass the filament through the filament detector, then insert it into the extruder and the nozzle. When you see the melted filament flow out from the nozzle, the filament is successfully loaded.
*When loading the filament, please make sure the distance between the Z-axis and the hotbed is beyond 5 cm.

Tips: How to Replace the Filament?

1. Cut the old filamentous above the extruder and slowly feed new filament in.
2. After the nozzle is preheated, push the old filament down a little way and withdraw it quickly, then feed the new filament in.

Adjust Z-axis Offset

Insert the storage card ➔click ➔ choose Auto-leveling Test. When printing the first layer, look at how well the model attaches to the hotbed, click ➔ Probe Z Offset to adjust the z-axis until the model can stick to the hotbed firmly, as shown in the following picture.

• The nozzle is too far from the hotbed,
• Perfect printing effect
• The nozzle is too close from the hotbed, click+
  

Start Printing

Click- ➔ Files ➔ 52] Printing would start once you choose a file, then the hotbed and nozzle start to heat in sequence.
During your printing process, you can click” ” to pause or stop the printing, adjust printing speed, and the like. {If the height of the z-axis is found improper, you can enter ➔ Probe Z Offset to adjust the z-axis again).

1. Click “Print”
   

2. Choose a file
   

3. Confirm the print
   

4. Preheating
   

5. . Printing Menu
   

6. Z-axis Offset
   

When using mirror or duplication mode, users need to add raft to the model when slicing .

Filament Detection Function

When the filament accidentally disconnected or runs out during printing, the printer will make a loud buzz to alert the user, and printing would be paused. The filament detection module is above the extruder. The user needs to use the change filament function to withdraw the original filament, insert the new filament into the extruder, and then click Resume on the screen to continue printing.

Normally printing

Filament disconnected, the printer buzzes

The screen shows printing paused

Mainboard Information

SHENZHEN KYW003D TECHNOLOGYCO., LTD.
Address: Room 1101, Yifenghua Building, N0.28 Yifenghua Innovation Industrial Park, Xinshi Community, Dalang Street, Longhua District, Shenzhen
Official Website : www.kywoo3d.com
Official FacebookAccount: KywooOfficial
Tel: +86 0755-21009224
Email: service@kywoo3d.com

Frequently Asked Questions

How to flash the firmware?

!.Download the corresponding firmware file on the Kywoo official website (www.kywoo3d.com).
Copy the file to the SD card.
Insert the SD card into the machine, press and hold the reset switch on the side of the printer until it enters the home page.

White screen or poor display?

!.Check whether the LCD ribbon cable is loose.
2. Flash the firmware again; if the issue cannot be solved, please contact our customer support(service@kywoo3d.com).

The file name is garbled and cannot be read?

1. Modify the file name to a number or English format.
2. Re-slice the model file.

The nozzle cannot be heated?

Check whether the nozzle harness is loose.
Check whether the current temperature of the nozzle is normal; if it is abnormal, the nozzle thermistor is damaged.
lf the current temperature is normal, the heating tube is damaged.

The hotbed cannot be heated?

1. Check whether the wiring harness under the heating bed is loose.
2. Check whether the current temperature of the hotbed is displayed normally; if it is abnormal, the hotbed thermistor is damaged.
3. lf the current temperature is normal, the hotbed plate is damaged.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>