ekwb P P240 Surface Radiator User Guide
- June 12, 2024
- ekwb
Table of Contents
ekwb P P240 Surface Radiator
Product Information: EK-Quantum Surface Radiator
The EK-Quantum Surface Radiator is a high-performance cooling component designed for liquid cooling systems. It features a classical U-shape coolant flow with inlet and outlet ports on one side of the radiator. The radiator is available in different variants, including S, P, and X series, each offering specific features and sizes.
Setup Configurations
The radiator can be set up in different configurations to suit your custom loop. It is important to use the extenders on any inlet and outlet position to avoid leakage. The radiator also has a fill/drain port for easy filling or draining of the loop, located opposite to the inlet/outlet side.
Inlet and Outlet Options
For the most optimal performance, it is recommended to use the same number of inlets and outlets. The radiator allows you to choose which port will serve as an inlet and which will serve as an outlet in your custom loop. However, on non-multiport radiators, you can choose only one inlet and one outlet port.
Product Variants
The EK-Quantum Surface Radiator is available in the following variants:
- S Series: Includes two Quantum Surface end tank shrouds (aluminium), two Quantum Surface side plates (stainless steel), and two Quantum Surface extenders.
- P Series: Includes two Quantum Surface end tank shrouds (aluminium), two Quantum Surface side plates (stainless steel), two Quantum Surface extenders, and three Quantum Surface plugs (multiport version).
- X Series: Includes two Quantum Surface end tank shrouds (aluminium), two Quantum Surface side plates (stainless steel), two Quantum Surface extenders, and three Quantum Surface plugs (multiport version).
Product Usage Instructions
- Carefully read the manual before beginning with the installation process.
- Use EK Fittings and screw them firmly in place using a small amount of force. The rubber O-ring gaskets ensure a liquid seal.
- Use market-proven corrosion-inhibiting coolants for optimal performance. Avoid using pure distilled water as a cooling liquid. EK-CryoFuel Coolants are recommended by EK for best results.
- Choose the desired inlet and outlet ports on the radiator based on your custom loop configuration.
- Ensure that the extenders are tightened properly to avoid leakage.
- If using the multiport radiator, use the fill/drain port for filling or draining the loop. Do not use it as an inlet or outlet port.
For any support or service inquiries, refer to the support section in the user manual. You can also connect with EK on social media for additional assistance.
Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance. We disclaim our liability for any damages to the product as well as incidental, consequential, or indirect damages incurred due to improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
- Carefully read the manual before beginning with the installation process.
- EK Fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured with the rubber O-ring gaskets.
- The use of quality market-proven corrosion-inhibiting coolants is always strongly recommended for any liquid cooling system.
- Do not use pure distilled water as a cooling liquid! For best results, EK recommends the use of EK-CryoFuel Coolants.
EK-QUANTUM SURFACE RADIATORS
EK-Quantum Surface Radiators have a classical U-shape coolant flow, with inlet
and outlet both on one side of the radiator. However, you can still choose
which port of the radiator will serve as an inlet, and which for the outlet in
your custom loop.
SETUP 1
Picture on the left shows the first flow direction setup of the EK-Quantum
Surface P360M Radiator which is a Multiport radiator. On the non-multiport
radiator you can choose only one inlet and one outlet port.
SETUP 2
Picture on the left shows the second flow direction setup of the EK-Quantum
Surface P360M Radiator which is a Multiport Radiator. On the non-multiport
radiator you can choose only one inlet and one outlet port.
- EK recommends using the same number of inlets and outlets for the most optimal performance!
- It is mandatory to use the extenders on any inlet and outlet position!
- If transferred from the stock position of the radiator to another, check if the extenders are tightened to avoid leakage!
- The same port setup applies for all EK-Quantum Surface radiator variants!
- On the Multiport Radiator, opposing to the inlet/outlet side of the radiator, there is an extra port for filling or draining the loop.
- It should not be used as an inlet or an outlet port!
EXPLODED VIEW OF THE REMOVABLE COMPONENTS FOR S, P AND X SERIES
EK-QUANTUM SURFACE S SERIES
EK-QUANTUM SURFACE P SERIES
EK-QUANTUM SURFACE X SERIES
SUPPORT AND SERVICE
In case you need assistance, please contact: https://www.ekwb.com/customer-
support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia – EU
SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks