EKWB EK-Quantum Convection D5 Pump Cover Instruction Manual

October 27, 2023
ekwb

EKWB EK logo

EK-Quantum Convection D5 Pump Cover
Instruction Manual

EKWB EK-Quantum Convection D5 Pump Cover

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our website at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure, and warranty conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning the installation process.
The use of quality market-proven corrosion-inhibiting coolants is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best results, EK recommends the use of EK-CryoFuel Coolants.

BOX CONTENTS

EKWB EK-Quantum Convection D5 Pump Cover - fig 1

REQUIRED TOOLS

D5 COVER DIMENSIONS

EKWB EK-Quantum Convection D5 Pump Cover - fig 3

MAIN PARTS

EKWB EK-Quantum Convection D5 Pump Cover - fig 4

Position EAN Description Quantity
1 100663 EK Badge 1
2 103312 D5 Cover Screw M4x62 – Black Chrome 4
103313 D5 Cover Screw M4x62 – Nickel
105360 D5 Cover Screw M4x62 – Gold
3 103314 D5 pump Cover – Black 1
103315 D5 pump cover – Nickel
103571 D5 pump Cover – Silver
105058 D5 pump Cover – Gold

PREPARING THE PUMP

EKWB EK-Quantum Convection D5 Pump Cover - fig 5

STEP 1
Unscrew the four (4) marked screws and remove the original pump holder. Store the holder and screws for possible reuse without D5 Cover. EKWB EK-Quantum
Convection D5 Pump Cover - fig 6

STEP 2
**UNINSTALLING MOLEX CONNECTOR*
4-PIN MOLEX CONNECTOR**

  1. Flatten the pins in Molex connector
  2. Remove Cables from Molex connector

3-PIN FAN CONNECTOR

  1. Push the pin on fan connector with screwdriver
  2. Remove the cable

ATTACHING THE PUMP COVER

EKWB EK-Quantum Convection D5 Pump Cover - fig 7

STEP 1
Insert the pump cables through D5 Pump cover and place the cover over D5 pump. Make sure that holes are aligned. Secure the D5 Pump cover using M4 x 62 mm screws and 2.5 mm Allen Key. Do not use excessive force while tightening the screws! EKWB EK-Quantum Convection D5 Pump Cover - fig
8

STEP 2
INSTALLING THE MOLEX CONNECTOR

  1. Put the screwdriver into pin gap in Molex connector
  2. Recover flattered pin into original position
  3. Put cables back to Molex connector and fan connector(Watch out for correct order of cables)

SUPPORT AND SERVICE

In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “MAIN PARTS” where you can find the EAN number of each part you might need. Include the EAN number with quantity in your request.
Mounting Mechanism EAN can be found under “BOX CONTENTS”.
Thermal pads are readily available in the EK shop.

SOCIAL MEDIA
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
EKWBofficial
ekwaterblocks

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals