VISUAL COMFORT TOB 5492 Truesdell 24 Inch Pendant Instruction Manual

VISUAL COMFORT TOB 5492 Truesdell 24 Inch Pendant

Product Information

• Product Name: Truesdell 24 Pendant
• Item Number: TOB 5492

Installation Requirements: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect the item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a clean, soft surface.
2. Remove the mounting plate (C) from the canopy (H) by removing the collar ring (I).
3. Connect the driver input neutral wire (white) to the supply neutral wire (usually white) using the wire nut (A).
4. Connect the driver input hot wire (black) to the supply hot wire (usually black) using the wire nut (A).
   • CAUTION: Do not reverse the hot and neutral connections.
5. Hang the fixture swivel ball (G) to the center of the mounting plate (C) and secure it with the set screw (D) using the provided wrench (E).
6. Cut excess wire, leaving enough to reach the junction box. Separate wires and strip insulation on each end by 5/8 inch.
7. Connect the fixture neutral wire (black) to the driver output wire (black) using the wire nut (A).
8. Connect the fixture hot wire (red) to the driver output wire (red) using the wire nut (A).
   • CAUTION: Do not reverse the hot and neutral connections.
9. Ensure all wire connections are tight, then carefully tuck them into the junction box.
10. Install the canopy (H) to the mounting plate (C) and secure it with the collar ring (I).
11. Install the metal shade (N) to the fixture (M) and secure it with the metal ring (O).
12. Thread the diffuser (N) to the metal ring (O).
    • NOTE: Do not over-tighten, as it may damage the glass.

NOTICE

This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slotted Screwdriver
• Wire Strippers
• Wire Cutters

Installation Instructions

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (C) from canopy (H) by removing collar ring (I).
3. Connect driver input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
4. Connect driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A).
   • CAUTION: Do not reverse the hot and neutral connections.
5. Insert driver (B) into junction box.
6. Install mounting plate (C) to the junction box and secure with mounting screws (F).
7. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten.
   • NOTE: It is imperative that the fixture is grounded.
8. Feed electrical wires through bottom rod (L) and connect to fixture (M). Repeat for middle rod (K), connecting to bottom rod (L).
9. Continue feeding wires through collar ring (I), canopy (H) and top rod (J).
10. Holding fixture upright, slide collar ring (I) and canopy (H) down and rest on fixture (M). Then connect top rod (J) to middle rod (K).
    • NOTE: Slide components down slowly to avoid damages.
11. Hang fixture swivel ball (G) to center of mounting plate (C) and secure with set screw (D) using provided wrench (E).
12. Cut excess wire, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
13. Connect fixture neutral wire (black) to driver output wire (black) using wire nut (A).
14. Connect fixture hot wire (red) to driver output wire (red) using wire nut (A).
    • CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (H) to mounting plate (C) and secure with collar ring (I).
17. Install metal shade (N) to fixture (M) and secure with metal ring (O).
18. Thread diffuser (N) to metal ring (O).
    • NOTE: Do not over-tighten otherwise glass could become damaged.

Care Instructions

• Clean only with a soft dry cloth or feather duster.
• Do not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>