Leaperkim Sherman-L Electric Unicycle User Manual
- August 8, 2024
- LeaperKim
Table of Contents
Leaperkim Sherman-L Electric Unicycle
Product Usage Instructions
- Caution:
- Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
- Compliance:
- This device complies with part 15 of the FCC Rules.
- Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Installation and Operation:
- This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body. Ensure proper placement to adhere to FCC radiation exposure limits.
FAQs
- Q: Can I modify the device?
- A: No, any changes or modifications not approved by the manufacturer may void your authority to operate the equipment.
Overview of the User Manual
- Thanks for purchasing the LeaperKim electric unicycle. We will wholeheartedly provide you with satisfactory products and services.
- This vehicle is strictly prohibited from driving on the motorway. It must be confirmed that it meets the requirements of local laws and regulations.
- Do not use this product in the areas prohibited by laws and regulations.
- Do not use this product at the speed specified by local laws and regulations.
- So that you can ride the LeaperKim electric unicycle more safely, please carefully read and understand all the product information and precautions listed in this manual before riding, and refer to the instructions to operate the LeaperKim electric unicycle.
- Please maintain the vehicle regularly, which will help to keep the performance and resale value of the vehicle product.
- Please keep this manual for future after-sales use.
- Your satisfaction with the Leaper Kim electric unicycle is our driving force!
Description of Product
Function Schematic
Product Size Drawing
Specification
Packing list
Packing list
No.| Description| Unit| Qty
1| Unicycle| PCS| 1
2| Charger| PCS| 1
3| User Manual| PCS| 1
4| Vehicle Information Card| PCS| 1
Function Introduction
Mid-mounted normal suspension
Function Introduction:
- Compression 18 clicks.
- Rebound 18 clicks.
- 12mm preload adjustable.
- Pressure relief valve.
Left and right Side Battery Pack
- Left Side Battery Pack Function Introduction:
- Long press the OK button and release until the display shows ln to enter left side battery pack mode.
- Press the switch button to check the voltage value of each series of cells.
- Press the switch button to check the temperature of 6 zones of cell groups.
- Press the switch button to check the battery running data-log.
- SSet running background time to perform battery balancing.
- Right Side Battery Pack Function Introduction:
- Long press the ‘OK ‘ button and release until the display shows ‘ln br’ to enter left side battery pack mode.
- Press the switch button to check the voltage value of each string of cells.
- Press the switch button to check the temperature of 6 zones of cell groups.
- Press the switch button to check the battery running data-log.
- SSet running background time to perform battery balancing.
Riding Mode Settable
Function Introduction:
- Long pressing the ‘OK’ button and release it until the display shows ‘in set’, pressing ‘OK’ to plus and minus the hardness values, values ranging from 0%-100%.
- The smaller the value, the softer it will be.
Button Volume Settable
Function Introduction:
- Long press the ‘OK ‘ button and release until the display shows br’ to enter left side battery pack mode.
- Press the switch button to check the voltage value of each string of cells.
- Press the switch button to check the temperature of 6 zones of cell groups
- Press the switch button to check the battery running data-log.
- Set running background time to perform battery balancing.
Low battery mode
Function Introduction:
- Long pressing the ‘OK’ button and release it until the display shows.’L mode’, pressing ‘OK’ to switch on and off. The smaller the value, the softer it becomes.
- OFF mode: Alarm when voltage is below 117V, and talk-back when voltage is below 113.4V.
- ON mode: Alarm when voltage is lower than 109.8V, and warping plate when voltage is lower than 106.2V.
High-Speed Mode
Function Introduction:
- Long pressing the ‘OK’ button and release it until the display shows ‘High S’, pressing ‘OK’ to switch on and off. The smaller the value, the softer it becomes.
- OFF mode: Maximum free-spin speed of 105 km/h;
- ON mode: Maximum free-spin speed of 125 km/h;
Angle Protection
Function Introduction:
- Long pressing the ‘OK’ button and release it until the display shows ‘Ang pt’, pressing ‘OK’ to enter the setting, values from 35°-70°.
- The larger the value, the greater the tilt angle will be.
Error codes and causes
Display introduction
Display Function Overview
Display Function Overview
Function Setting Area
Usage Notice
The following persons are prohibited from riding this product:
- Persons who are under the influence of drugs or alcohol and have limited mobility and reaction ability. Or people with hypertension, cardiovascular and cerebrovascular diseases or other high-risk diseases.
- Minors under 14 years old, pregnant women, mentally ill and the elderly over 60 years old.
- It is forbidden to drive at high speed or accelerate sharply when the battery is low.
- No jumping or riding on one foot
Do not carry out any dangerous
- Please control the speed reasonably where there are people or obstacles, and prohibit speeding.
- Please wear helmets, knee pads, elbow protectors, gloves, and other protective equipment before using this product.
- This product is not allowed to be disassembled or repaired by unprofessional personnel. If the machine is disassembled by oneself, the product warranty service will no longer be enjoyed.
- If the vehicle makes alarms, please stop riding it immediately and send it to the professional maintenance point for maintenance in time.
- Please carefully read and understand all the product information and precautions listed in this manual and follow the use behavior suggested in this manual to avoid unnecessary loss and injury, otherwise, you need to bear all the consequences arising therefrom.
- During the production or sales of this product, design changes and further improvement will be carried out continuously. In case of any discrepancy with this manual, please refer to the actual product.
Maintenance
- Use this product frequently, and check whether the screws are loose on time.
- Check the tire pressure on time. The suggested pressure is 2.5-3.0 bar.
- Better to put the vehicle in a dry area.
- Charge the battery to full charge at least once every two months.
- Avoid recharging when the battery is completely exhausted.
- Avoid placing the battery in an environment that is above 50 ·c or below – 20 ·c.
- It is prohibited to use chargers other than the standard charger for charging.
- It is forbidden to immerse this product in water and wash it with a high-pressure water gun.
Warranty
NO. | Items | Warranty time |
---|---|---|
1 | Controller, motor | 24 month |
2 | Battery packs | 18 month |
3 | Charger | 6 month |
The following conditions are not covered by the warranty and need to pay for maintenance.
- The validity period of three guarantees has expired.
- Damage caused by human factors.
- Damage caused by force majeure.
- All kinds of damage are caused by failure to use, maintain, and transform according to the requirements of the user manual.
- Failure or damage caused by forced use of this product beyond normal conditions.
- The product has been disassembled or maintained by personnel not authorized by our company.
- Malicious damage to warranty content and vehicle body information.
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.
CONTACT INFORMATION
- Manufacturer: Guangzhou Coyote Intelligent Equipment Co., Ltd.
- ADD: Part 1 of 3rd floor, No. 45-2, Northern Industrial Road, Xinlou village, Baiyun District, Guangzhou, China
- Tel: +86 13751045466
- Email: support@leaperkim.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>