B-TECH BT9901 XL Universal Flat Screen Wall Mount Installation Guide
- June 12, 2024
- B-TECH
Table of Contents
BT9901 XL Universal Flat Screen Wall Mount
Installation Guide
SPECIFICATIONS
- Recommended screen size: 65″ – 100″
- Max load: 100kg (220lbs)
- Universal screen interface fits screens with VESA® & non-VESA mounting patterns up to: 920 x 600mm
- Slim design mounts screen 30mm (1.2″) from wall
- Keyhole “hook-on” mounting for simple installation
- All mounting hardware and fixings included
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This mount s intended for use only with the maximum weights
indicated. Use with equipment heavier than the maximum indicated may result in
instability causing possible injury.
Do not attempt to install this product until all instructions and warnings
have been read and properly understood. Please keep these instructions for
future reference.
Please check carefully to make sure there are no missing or defective parts –
defective parts must never be used.
B-Tech AV Mounts, its distributors and dealers are not liable or responsible
for damage or injury caused by improper installation, improper use or failure
to observe these safety instructions. In such cases, all guarantees will
expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during
installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install
this product safely, then please consult a professional for advice and/or to
install this product for you. Failure to mount this product correctly may
cause serious injury or death both during installation and at any time
thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the
product you are installing.
This weight limit will be clearly stated on each product and its packaging and
will vary from product to product.
Product location
Please pay careful attention to where this product is located. Check load
capacity of the wall prior to installation as some surfaces are not suitable
for installation. Designed for indoor use, this mount is suitable for public
or home installation If located in a public or frequently populated area
ensure that the product is out of the immediate reach of people.
If any AV equipment is to be suspended over the likely path or location of
people then great care should be taken to secure all parts of the installation
from falling.
When drilling holes it is essential to avoid contact with electrical cables
and water or gas pipes contained within.
Use of a good quality live wire detector and hidden object locator is
therefore recommended.
Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. The fixing kit supplied with the product may not be suitable for
all walls.
If any fixing screws or included hardware are deemed not sufficient for a safe
installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installation double-
check that the work done is safe and secure. Double-check all necessary
fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing
points are made as frequently as possible (no more than 6 months apart) to
ensure that safety is maintained.
If in doubt consult a professional AV installer or other suitably qualified
person.
BT9901 PARTS LIST
PLEASEKEEP THS FORFLTLRE REFERENCE
| ITEM | PART NAME | QTY |
|---|---|---|
| 1 | WALL PLATE | 1 |
| 2 | INTERFACE ARM – RIGHT | 1 |
| 3 | INTERFACE ARM – LEFT | 1 |
SCREEN INTERFACE KIT
A| M6 x 16mm SCREW| 4
B| M6 x 25mm SCREW| 4
C| M6 x 40mm SCREW| 4
D| M8 x 16mm SCREW| 4
E| M8 x 25mm SCREW| 4
F| M8 x 40mm SCREW| 4
G| M6 METAL WASHER| 4
H| 5mm SPACER| 4
I| 13mm SPACER| 4
J| 24mm SPACER| 4
WALL FIXING KIT
Al| M8 x 50mm COACH SCREW| 6
A2| M8 METAL WASHER| 6
A3| N°.10 WALL PLUG| 6
Suitable for loads up to 100kg (220lbs)
INSTALLATION TOOLS REQUIRED
Drill
12mm (1/2°) masonry bit
or 6mm (1/4″) wood bit| Pencil| 13mm (1/2″)
spanner or socket| Screwdriver| Stud Finder
(Optional)
---|---|---|---|---
INSTALLATION INSTRUCTIONS
- FIX WALL PLATE
Fix item 1 to the wall using one of the following methods:
Concrete/brick wall
| Keyhole Mounting | Stud/wood wall |
|---|
| 
2. ATTACH INTERFACE ARMS TO SCREEN
Fix items 2 &3 to the rear of the screen using items A-J.
Note: Ensure the arms are facing the correct way round and the same holes
are used on both arms.
- MOUNT SCREEN ONTO WALL PLATE
” i. Hook items 2& 3 onto item 1.
REMOVING THE SCREEN
Pull the string down on items 2 & 3 to unlock the screen and remove from item
TWIN POLE MOUNTING
BT9901 DIMENSIONS
PLEASE KEEP THIS FOR FUTURE REFERENCE
CONTACT:info@btechavmounts.com
©2021 B-Tech International Design and Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design and
Manufacturing Ltd.
B-Tech AV Mounts and the B-Tech logo are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA-BT9901-V1.2-1021-123 MADE IN THE P.R.C.
**** For More Information Visit www.btechavmounts.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>