ABYSM AB812111W Danube Mura BX300 White ARGB Tower User Manual

**ABYSM AB812111W Danube Mura BX300 White ARGB Tower User Manual

**

CAUTIONS

• Please read this manual carefully before proceeding with the installation.

• Check the product and components before starting the installation. If you find an abnormality, please contact the place where you purchased the product for a replacement or refund.

• Wear gloves to avoid accidents when installing the product.

• Serious damage can occur when mounting the system, so do not apply excessive force.

• Incorrect connection of wires may cause a fire due to a short circuit. Be sure to check the manual when connecting cables.

• Be careful not to block the ventilation ducts when using the product.

• Avoid places with direct sunlight, water, humidity, oil and excessive dust. Store and use the product in a well-ventilated place.

• Do not clean the surface of the product with chemicals (organic solvents such as alcohol or acetone).

• Do not insert your hand or any other object into the product during operation, as this may hurt your hand or damage the object.

• Our company does not assume any responsibility for any problems that occur due to the use of the product for purposes other than those designated and / or the carelessness of the consumer.

• Product design and specifications may be revised to improve quality and performance without notice.

INSTALLATION MANUAL

• Open left panel & right panel by screws
  

• Pull front panel from the bottom
  

MOTHERBOARD INSTALLATION

• Motherboard location

• Fit I/O into I/O slot
  

• Put motherboard to the location and fix it with screws
  

2,5’’ SSD AND 3,5’’ HDD INSTALLATION BESIDE MOTHERBOARD (OPTIONAL)

• Support six 2.5’’ SSD or 3.5’’ HDD brackets (optional)
  

• Put SSD to the location
  

• Fix SSD with M/B screws from the back
  

• Or put HDD to the location
  

• Fix HDD with HDD screws from the two sides
  

• Fix the bracket with SDD or HDD into the location
  

2,5’’ SSD AND 3,5’’ HDD INSTALLATION ON THE BOTTOM PLATE

• Take out bracket from bottom plate
  

• Put SSD to the location

• Fix SSD with M/B screws from the back

• Put HDD to the location on the top of the bracket

• Fix HDD with HDD screws from inside of the bracket
  

• Push HDD into the bracket

• Fix HDD with HDD screws from the sides

• Push the bracket back to bottom plate

2,5’’ SSD AND 3,5’’ HDD INSTALLATION ON THE MOTHERBOARD BRACKET

• Remove the bracket
  

• 1×3.5’’ HDD or 2×2.5’’ SSD location

• Put 2×2.2’’5 SSD to bracket

• Fix them with M/B screws from the back of bracket

• Put 1×3.5’’ HDD to bracket
  

• Fix it with HDD screws from the back of bracket
  

• Fix the bracket with screws
  

2,5’’ SSD AND 3,5’’ HDD INSTALLATION ON THE PSU COVER

• 1×3.5’’ HDD or 2 x 2.5’’ SSD location
  

• Unscrew the screws and remove the bracket
  

• Put 2×2.2’’5 SSD to bracket
  

• Fix them with M/B screws from the back of bracket
  

• Put 1×3.5’’ HDD to bracket
  

• Fix it with HDD screws from the back of bracket
  

• Fix the bracket with screw
  

• The left HDD as shown
  

FANS ON THE FRONT

• Fan location

• Put 3×120 mm or 3×140 mm fans to fan location

• Fix fans with screw.

FANS ON THE REAR

• Fan location
  

• Put 1×120 mm fan to fan location

• Fix fans with screws

FANS ON THE TOP

• Fan location

• Put 3×120 mm or 2×140 mm fans to fan location

• Fix fans with screws
  

FANS ON PSU COVER

• Fan location
  

• Put 3×120 mm fans to fan location
  

• Fix fans with long screws from the top of fan
  

TRANSVERSE VGA CARD INSTALLATION

• VGA card location

• Remove the PCI card slot
  

• Put VGA card to the slot

• Fix it with screws

VERTICAL VGA CARD INSTALLATION

• Remove the PCI cars slot
  

• Put the extension cable to the location
  

• Put the other side to the slot
  

• Fix the VGA card to the location and fix it with screws
  

POWER SUPPLY INSTALLATION

• Power Supply location
  

• Put the Power Supply to the location
  

• Fix it with screws
  

USB 3.0 INSTALLATION

• Plug in USB3.0 connector to the motherboard

• I/O ports on the top

HD AUDIO INSTALLATION

• Plug in HD Audio connector to the motherboard

CABLE CONNECTION

Insert the hard disk indicator onto the pins marked with “HDD LED”, “HD LED”, “HLED” or “IED LED”.

Insert the power switch indicator onto the pins marked with “PWR LED” on the mainboard

Insert the Reset switch key onto the pins marked with RST SW / RES SW / RST

Insert the power switch key onto the pins marked with “PWP SW”, “PWR BTN” or “RWR” on the mainboard

NOTE: Follow the positive electrode -positive electrode, negative electrode – negative electrode connection. Reverse connection is prohibited

References

• Inicio - ABYSM GAMING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>