V I V O Mount-TVSG1 Micro Gap Flat TV Wall Mount Instruction Manual

: June 12, 2024
: V I V O

Table of Contents

SKU: MOUNT-TVSG1
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O Mount-TVSG1 Micro Gap Flat TV Wall Mount

SKU: MOUNT-TVSG1

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual

https://vivo-us.com/products/mount-tvsg1

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use

PACKAGE CONTENTS

A (x1) Left Wall Plate
B (x1) Right Wall Plate
C (x1) Left TV Plate
D (x1) Right TV Plate
E (x1) Kickstand
F (x2) Protective Film
G (x4) Square Pad
H (x2) Round Pad
I (x1) Sticker
M-A (x2) M8x55mm Screw
M-B (x3) M8x18mm Screw
M-C (x2) M8x10mm Screw
M-D (x2) Spacer
W-A (x8) ST5.5x55mm Screw
W-B (x8) Anchor
T-A (x1) Measuring Tape

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

TOOLS NEEDED

CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.com , email at help@vivo- us.com, or call us at 309-278-9303.

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

ASSEMBLY STEPS

STEP 1

Find the center of your TV using Measuring Tape (T-A). Mark the distance of your TV’s top VESA mounting holes on Measuring Tape (T-A). If the VESA holes are 1000mm (39.4”) or greater, swap Left Wall Plate (A) and Right Wall Plate (B), and use the orientation through the remainder of the manual.

STEP 2 (Option A)
Stud / Wood Wall Installation
Secure Measuring Tape (T-A) to the wall in the desired location using Stickers (I). Align the marks on Measuring Tape (T-A) with the outside of the tabs on Left Wall Plate (A) and Right Wall Plate (B). Mark drilling locations. Use of a stud finder and level is recommended.

Pre-drill the marked location. For drywall, use an 8mm (5/16”) drill bit, and drill approximately 60mm (2.4”). For studs, use a 4mm (5/32”) drill bit, and drill approximately 55mm (2.2”) deep.

Insert Anchors (W-B) and mount wall plates using ST5.5x55mm Screws (W-A) and a Phillips screwdriver.

Note: The brackets are showing the setup for a 800mm or less VESA pattern.
STEP 2 (Option B)

Concrete/Brick Wall Installation
Secure Measuring Tape (T-A) to the wall in the desired location using Stickers (I). Align the marks on Measuring Tape (T-A) with the outside of the tabs on Left Wall Plate (A) and Right Wall Plate (B). Mark drilling locations. Pre-drill the marked locations, and use an 8mm (5/16”) drill bit drilling appoximately 60mm (2.4”) deep. Insert Anchors (W-B) and mount wall plates using ST5.5x55mm Screws (W-A) and a Phillips screwdriver
Note: The brackets are showing the setup for a 800mm or less VESA pattern.

STEP 3 (Option A)

For AU8000-AU9000, Q60A-70A, QN85A-QN95A, QN800A, QN900A, Q800A, Q900A Remove the adhesive backing from Protective Film (F) and place them over the top VESA holes on the TV, making sure the arrows are facing inward.

For AU8000-AU9000, Q60A-70A, QN85A-QN95A, QN800A, QN900A, Q800A, Q900A Assemble Left TV Plate (C) and Right TV Plate (D) to the TV using Spacers (M-D) and Screws (M-A through M-C). Snap in Spacers (M-D) between the tabs on TV Plates (C,D) with the raised side facing down. Remove adhesive backing from Square Pads (G) and place them on the back of the TV. Mount Kickstand (E) to one of the lower VESA holes using M8x18mm Screw (M-B) to access the TV ports.

STEP 3 (Option B)

Other Models and Mounting with One Connect Box Assemble Left TV Plate (C) and Right TV Plate (D) to the TV using Spacers (M-D) and Screws (M-A through M-C) and the spacers provided with your TV. Remove the adhesive backing from Round Pads (H) and place them at the bottom of the TV with the spacers provided with your TV. Install the One Connect Box using the hardware provided with the TV.

STEP 4
Hang Left TV Plate (C) and Right TV Plate (D) over Left Wall Plate (A) and Right Wall Plate (B). Pull down on TV to lock TV Plates (C,D) into Wall Plates (A,B).

STEP 5

To remove the TV, lift up on one side first to unlock one plate, then lift on and unlock the other side. Lift the TV up and out of the mount.

Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M