SATCO 62-1700 CCT Selectable Blink LED Flush Fixtures Instruction Manual
- June 12, 2024
- SATCO
Table of Contents
62-1700 CCT Selectable Blink LED Flush Fixtures
Instruction Manual
CCT Selectable
2700K/3000K/3500K/4000K/5000K
CCT SELECTABLE BLINK LED FLUSH FIXTURES
Models: 62-1700, 62-1701, 62-1702, 62-1703, 62-1704, 62-1705, 62-1706,
62-1707, 62-1710,
62-1711, 62-1712, 62-1713, 62-1714, 62-1715, 62-1716, 62-1717, 62-1718,
62-1719, 62-1720,
62-1721, 62-1722, 62-1723, 62-1724, 62-1725, 62-1726, 62-1727, 62-1728,
62-1729
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
- Disconnect power before installation or maintenance of the fixture.
- To avoid damage, falling, electric shock or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
- Only authorized, qualified personnel should install this fixture and should follow the owner’s manual. Any improper installation might cause failure, electric shock, fire or other injury, damage or hazard.
- To prevent fire, this fixture is rated for use in 120VAC.
- 010V models are 120/277V. See 010V wiring diagram.
- The product is purposed for interior use only, suitable for wet locations.
- Suitable for use with dimmers. Visit www.Satco.com for a list of compatible dimmers.
- Protect the product against direct contact with water.
- For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
- Clean with a soft or damp cloth, making sure the power is OFF.
- Assemble the product only with the use of parts provided and the housing; improper assembly may result in device failing which could damage the product, personal property or cause injury.
- CAUTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
The circuit is intended for connection to an external Class 2 supply. Any
changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
WARRANTY: This product is guaranteed for a 5 year warranty. Any quality
issue in normal use within the warranty period, will be repaired or replaced
according to the situation and under the condition specifications can be
provided. Visit www.Satco.com for full warranty details.
Wiring Diagrams
NOTE: 0-10V wiring for models: 62-1718, 62-1719,
62-1728, 62-1729 (120/277V)
INSTALLATION – 3″ & 4″ Junction Box
(*Fits most 3″ and 4″ Junction Boxes with a minimum interior cubic volume of
14 in.)
STEP 1: Turn OFF power prior to installation. Before installation, select
your preferred CCT by moving the switch to either 2700K, 3000K, 3500K, 4000K
or 5000K. 
STEP 2: Screw the mounting
plate on the junction box.
STEP 3: Connect the wires with wiring caps. See wiring
diagrams. S TEP 4: Align the clips with the mounting plate and push the
fixture up into junction box. Turn ON power. Installation is complete. 
INSTALLATION – 3″ & 4” Pancake Junction Box
STEP 1 : Turn OFF power prior to installation. Before installation,
select your preferred CCT by moving the switch to either 2700K, 3000K, 3500K,
4000K or 5000K.
STEP 2: Screw the
installation accessory on 3″ & 4″ pancake junction box. 
STEP 3: Connect the wires with wiring caps. See wiring diagrams.
STEP 4: Align the clips
with the mounting plate and push the fixture up into junction box. Turn ON
power. Installation is complete.
Satco Products, Inc.
Brentwood, NY 11717
© Copyright 2022 Satco Products, Inc. 11/22 v1.5
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>