saxby lighting 76617 Ikon Pro CCT Outdoor LED Kit Instruction Manual

76617 Ikon Pro CCT Outdoor LED Kit
Instruction Manual

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

** The power supply is Double Insulated and does not require connection to an Earth circuit.**

The LED units are Safety Extra Low Voltage and must not be earthed.

Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
This system operates at Safety Extra Low Voltage (12V), via an LED driver. Never connect the light fittings directly to the mains without using the supplied driver.
The mains plug must be situated indoors (e.g. house, garage, shed) in order to protect it from the elements.

Specification

The Kit contains:

• 1 x IP67-rated driver with 3 meters of mains cable and mains plug.
• 1 x 5m extension cable
• 2 x 5 LED head looms (total length 7.5m per loom)
• 12 x end plugs

Power Supply: 220-240V 50Hz. Output: 12V DC 15W Max. Constant voltage
Lamp: 73347, 73348, 73349 Ikon Pro CCT 25mm, 35mm, 45mm – Warm white (3000K)/Cool white (4000K)
76615, 76616, 76617 Ikon Pro CCT 25mm, 35mm, 45mm – Daylight white (6500K)/Blue (20000K)
IP rating: 67

Layout

• Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the mains plug, the LED driver, and each light fitting.
• Avoid locating any cables in positions that would cause a trip hazard. Position cables and drivers away from areas where they may be at risk of being cut, trapped, or damaged.
• The mains plug must be situated indoors. The kit can be wired into an IP67 external terminal block. (Recommended terminal block ref 61515). This must be carried out by a  competent and qualified electrician.
• The driver and LED head units are rated at IP67 and can be positioned outdoors.
• These fittings are designed to be used in decking and must not be mounted/installed in concrete.
• A PIR sensor (71553) and photocell sensor (71554) are available to purchase separately for this kit.

Installation

This LED kit has been specifically designed for use in decking and combines some innovative features to make installation easier:

• 2x prewired looms each with 5 LED heads plus a 5m extension cable allowing longer runs to be achieved.

• The wiring loom can be fitted into the deck during construction.

• Heads are interchangeable allowing different sizes and colors to be operated from one power source.
  1. Position the plug next to the indoor mains outlet socket that the system will connect to. Do not plug in at this stage.
  2. After deciding the layout of the light fittings, ensure the cables are long enough to connect to the desired positions. The maximum distance between heads is 1.5m.
  3. Drill the mounting holes for the light units taking care not to damage any pipes or main cables beneath the mounting surface. The minimum hole depth is 80mm.
  Cutting hole sizes are as follows:- 25mm diameter lights = 20mm cutting hole

• 35mm diameter lights = 25mm cutting hole

• 45mm diameter lights = 32mm cutting hole
  4. From underneath the decking, feed the connector and cable up through each installation hole. (A).
  5. Fit the protective cap onto the connector – to prevent the unit from dropping back through the hole and to keep debris out. (B).
  6. Once the decking has been fully assembled and the lights are ready to be installed, remove the protective cap and push the LED head unit onto the connector observing the correct polarity. See CCT Function below. (C)
  7. Fit the assembled head units by pushing them into the holes. The springs on the side of the head will secure the head units in place. (D)
  8. Connect all looms together and connect directly to the driver output cable or the extension cable.
  9. Ensure any unused heads and cable ends are fitted with the end plug and protective cap to prevent the ingress of moisture.
  10. Plug the mains plug into the socket and switch on to test.

CCT Function

• These kits are supplied with removable and interchangeable heads. For 73347, 73348, and 73349, it is possible to choose between warm white (3000K) and cool white (4000K)  light output. For 76615, 76616, and 76617, it is possible to choose between daylight white (6500K) and blue light (20000K) output.

• To change the color you simply turn the LED head 180°and reinsert it back into the loom, according to the arrows on the connector as detailed below and in Fig. E.

• 73347/73348/73349
  – Arrow on the LED head unit is connected to arrow 1 on the connector = Warm white (3000K)
  – Arrow on the LED head unit is connected to arrow 2 on the connector = Cool white (4000K)

• 76615/76616/76617
  – The arrow on the LED head unit is connected to arrow 1 on the connector = Daylight white (6500K)
  – The arrow on the LED head unit is connected to arrow 2 on the connector = Blue light (20000K).

Wiring

If not using the supplied plug then the product must be wired to an IP67 (or higher rated) terminal block(recommended terminal block ref 61515).

Having correctly identified the wiring from your existing light fitting, connect to the approved outdoor rated external terminal block in the following way:

Care and Cleaning

We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
To prolong its life and keep your outdoor lighting in good condition, it is recommended that periodically it is cleaned using a soft cloth followed by the application of a light coating of oil, such as WD40.

Do not clean the units with a pressure washer.

Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

Safety information

Live Voltages may be present in the transformer even when turned off or when completely disconnected.
For your safety, always switch off the supply before maintaining the system.
‘The LED module of this luminaire is not replaceable, when the LED module reaches its end of life the whole luminaire shall be replaced

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>