roborock S8 Pro Ultra Robotic Vacuum Cleaner User Manual

roborock S8 Pro Ultra Robotic Vacuum Cleaner

Safety Information

WARNING

• For use only with roborock EWFD07LRR or EWFD08LRR charger.
• Place the cords from other appliances out of the area to be cleaned.
• Do not operate the vacuum in a room where an infant or child is sleeping.
• Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor to be cleaned.
• Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.
• Do not allow children to sit on the vacuum.
• Do not carry the product using dock base or dustbin.
• Place the dock on a flat floor away from fire, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in the air.
• The product must be switched off and the plug must be removed from socket outlet when not in use, before cleaning or maintaining the product.
• This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.
• Do not dismantle, repair or modify the battery or charging dock.
• If the dock is placed in an area susceptible to thunderstorms or with unstable voltage, take protection measures.
• Connect to a properly grounded outlet only. See Grounding Instructions.

GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that looks like the plug illustrated in sketch A in Grounding methods. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adaptor should be used with this appliance.

Battery and Charging

• Keep the charging dock away from heat (such as radiators).
• Do not wipe the charging contacts with wet cloth or wet hands.
• Turn the robot off and use original packaging for shipment.
• If placing the robot into storage, charge it fully and turn it off before placing it in a cool dry place. Recharge it at least every three months to prevent the battery over discharging.
• Do not use the product when the temperature is higher than 40°C (104°F) or lower than 4°C (39°F), or there is any liquid or sticky substance on the floor.

International Symbols Explanation

• ALTERNATING CURRENT symbol [symbol IEC 60417-5032 (2009-02)]
• DIRECT CURRENT symbol [symbol IEC 60417-5031 (2009-02)]
• PROTECTIVE EARTH (Protective Ground) symbol [symbol IEC 60417-5019 (2009-02)]

FCC/IC Statement

Compliance Information

Product Name| Robotic Vacuum Cleaner with Charging Dock
Product Model| Robotic Vacuum Cleaner Model: S81USP

Empty Wash Fill Dock: EWFD07LRR, EWFD08LRR

Compliance Statement

| This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)  this device may not cause harmful interference, and

(2)  this device must accept any interference received, including interference that may cause undesired operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1)  This device may not cause interference.

(2)  This device must accept any interference, including interference that may cause undesired operation of the device.

Correspondence of the responsible party in USA
Company| Roborock Technology Co.
Address| 16192 COASTAL HWY LEWES, DE 19958 US.
Email| support@roborock.com

Product Overview

Robot (Top View)

• Mop Only/Child Lock
  • Press to start mopping
  • Press and hold for 3 seconds to turn on/off the child lock
• Power/Clean
  • Press and hold to turn the robot on or off
  • Press to start cleaning
• Power Indicator Light
  • White: Battery level ≥ 20%
  • Red: Battery level < 20%
  • Pulsing: Charging or starting up
  • Flashing red: Error
• Dock
  • Press to return to dock/start emptying
  • Press and hold to wash mop

1. Vertical Bumper
2. LiDAR Sensor
3. Wall Sensor
4. Charging Contacts
5. Reactive 3D Obstacle Avoidance Sensor
6. Infrared Fill Light

Robot (Bottom View)

1. Cliff Sensors
2. Carpet Sensor
3. Omnidirectional Wheel
4. Side Brush
5. Main Brushes
6. Main Brush Cover
7. Main Wheel

Robot (Upper Cover Open)

1. WiFi Indicator Light
   • Off: WiFi disabled
   • Flashing slowly: Waiting for connection
   • Flashing quickly: Connecting
   • Steady: WiFi connected
2. Reset Button
3. Bumper
4. Mop Wash Sensor
5. Water Tank
6. Self-Filling Port
7. Positioning Button
8. VibraRise Module
9. Air Outlet

VibraRise Mop Mount

1. Mop Cloth Attachment Slot
2. Vibration Module
3. Mop Cloth Mount

VibraRise Mop Cloth

1. Hook and Loop Pads

Dustbin

1. Cover Latch
2. Filter Cover
3. Dustbin Latch
4. Air Inlet
5. Washable Filter

• Power Cable
• Dock Base
• Disposable Dust Bag

Empty Wash Fill Dock

1. Water Tank Handle
2. Water Tank Lid
3. Dirty Water Tank
4. Dock Location Beacon
5. Self-Filling Port
6. Charging Contacts
7. Washing Strip
8. High-Speed Maintenance Brush
9. Maintenance Brush Latch
10. Dustbin
11. Clean Water Tank
12. Water Tank Latch
13. Status Indicator Light
    • Pulsing: Emptying/Washing Mop
    • Red: Dock error
    • Light off: Powered Off/Charging/ Drying
14. Water Filter
15. Air Inlet
16. Dock Base
17. Hot Air Outlet

Power Cable Storage

• Cable Outlets
• Cable Slot
• Power Port

Note: Power cable can exit at either side.

Installation

Important Information

1. Tidy cables and loose items from the ground and move any unstable, fragile, precious, or dangerous items to prevent personal injury or property damage due to items becoming tangled in, struck by, or knocked over by the robot.
2. When using the robot in a raised area, always use a secure physical barrier to prevent accidental falls that may result in personal injury or property damage.
   Note: When using the robot for the first time, follow it throughout its whole cleaning route and watch for potential problems. The robot will be able to clean by itself in future uses.

Position the charging dock

1. Place the dock on a hard and flat floor.
2. Attach the base by pressing down both sides of the base firmly, and then pressing the connecting part in the middle until you hear a click.
3. Connect the power cable to the back of the dock, and keep the excess cable inside the storage slot.
4. Place the dock on a hard and flat floor (wood/tile/concrete etc.), flat against a wall. Keep at least 0.7 m (2.3 ft) in front and 0.8 m (2.6 ft) above. Make sure the location has good WiFi for a better experience with the mobile app, and then plug it in.
5. more than 0.8 m (2.6 ft)
6. more than 0.7 m (2.3 ft)

Notes:

• If the power cable hangs vertically to the ground, it may be caught by the robot, causing the dock to be moved or disconnected.
• The dock indicator is on when the dock is powered on, and off when the robot is charging.
• The dock indicator turns red if an error occurs.
• Place the dock on a flat floor away from fire, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may cause the dock to tilt over and cause problems docking and departing.
• Keep the dock away from direct sunlight or anything that may block the dock location beacon; otherwise, the robot may fail to return to the dock.
• Do not use the dock without a clean water tank, dirty water tank, high-speed maintenance brush, dustbin, dust bag or water filter.
• Maintain the dock according to the maintenance instructions. Do not clean the dock with a wet cloth or tissue.
• All docks are subject to water-based tests before leaving the factory. It is normal that a small amount of water remains in the waterway of the dock.

Power on and charge the robot
Press and hold the button to power on the robot. When the power light goes on, place the robot on the dock to charge. Make sure the charging dock power indicator turns off and a “charging” voice alert sounds. To maintain the performance of the high-performance lithium-ion rechargeable battery pack, keep the robot charged.
Note: The robot may not be turned on when the battery is low. In this case, connect the robot to the dock.

Connecting to the App

This robot supports both Roborock and Xiaomi Home apps. Choose the one that best meets your needs.

Download App

1. Option 1: Search for “Roborock” in the App Store or Google Play or scan the QR code to download and install the app.
2. Option 2: Search for “Xiaomi Home” in the App Store or Google Play or scan the QR code to download and install the app.

Reset WiFi

1. Open the top cover and find the WiFi indicator.
2. Press and hold the and buttons until  you hear the “Resetting WiFi” voice alert. The reset is complete when the WiFi indicator flashes slowly. The robot will then wait for a connection.

Note: If you cannot connect to the robot due to your router configuration, a forgotten password, or any other reason, reset the WiFi and add your robot as a new device.

Add device
Open the Roborock App, tap the “Scan to Connect” button, or open the Xiaomi Home app, tap “+” in the top right corner and add the device as instructed in the app.

Notes:

• The actual process may vary due to ongoing app updates. Follow the instructions provided in the app.
• Only 2.4 GHz WiFi is supported.
• If the robot waits more than 30 minutes for a connection, WiFi will be automatically disabled. If you want to reconnect, reset the WiFi before proceeding.

Instructions

Filling the Clean Water Tank
Open the clean water tank and fill the tank with water. Close the lid, lock the latch, and fit the tank back in place.

Notes:

• To prevent corrosion or damage, only use the Roborock branded floor cleaner in the water tank.
• To avoid water tank deformation, do not place hot water in the tank.
• If water marks remain on the water tank, wipe them clean before reinstallation.

On/Off
Press and hold the button to turn on the robot. The power indicator will turn on and the robot will enter standby mode. Press and hold the button to turn off the robot and complete the cleaning cycle.
Note: The robot cannot be turned off when it is being charged.

Starting Cleaning
Press the button to start cleaning. The robot will plan its cleaning route according to its scan of the room. It splits a room into zones, first draws out zone edges, and then fills the zone in a zigzag pattern. In so doing, the robot cleans all zones one by one, efficiently cleaning the house.

Notes:

• To allow the robot to automatically vacuum and return to the dock, start the robot from the dock. Do not move the dock during cleaning.
• Cleaning cannot start if the battery level is too low. Allow the robot to charge before starting the cleanup.
• If cleaning is completed in less than 10 minutes, the area will be cleaned twice.
• If the battery runs low during the cleaning cycle, the robot will automatically return to the dock. After charging, the robot will resume where it left off.
• When the mop mount is attached, the robot will retract it when cleaning the carpet. You can also set the carpet as a no-go zone in the app to avoid it.
• Before starting each mopping task, make sure that the VibraRise mop has been properly installed.

Spot Cleaning
Press and hold and buttons simultaneously to start spot cleaning. The robot cleans a 1.5 m (4.9 ft) x 1.5 m (4.9 ft) square area centered on itself.
Note: After spot cleaning, the robot will automatically return to the starting point and enter Standby mode.

Mop Only
Press the button to start mopping only. The main brushes rise and the main brushes and fan stop operating.
Note: Compared with traditional cleaning mode, noise occurred by Mop Only is much lower.
Pause
When the robot is running, press any button to pause it, press the button to resume cleaning, and press the button to send it back to the dock.
Note: Placing a paused robot on the dock manually will end the current cleanup.

Sleep
If the robot is paused for over 10 minutes, it will go to sleep, and the power indicator will flash every few seconds. Press any button to wake the robot up.

Notes:

• The robot will not go to sleep when it is charging.
• The robot will automatically shut down if left in sleep mode for more than 12 hours.

Mop Washing
During cleaning, the robot automatically determines when it should return to the dock for mop washing and water tank refilling to maximize its mopping performance. To manually start washing, tap Wash button in the app or press and hold the button on the robot to send it back. Press any button to stop washing.

Notes:

• To allow the robot to wash the mop automatically, start the robot from the dock and do not move the dock during cleaning.
• Mop washing duration is 20 minutes by default and you can modify this duration or washing mode in the app.

Emptying
Auto-emptying will automatically begin when the robot returns to the dock after cleaning. To manually start emptying, pres button on the docked robot or tap Empty button in the app. Press any button to stop emptying.

Notes:

• When auto-emptying has been left unused for a long period, empty the dustbin manually and make sure the air inlet is clear for optimal emptying performance.
• Auto emptying can be disabled through the app.
• Avoid frequent manual emptying.

Drying
Drying starts automatically after mop washing or after cleaning are completed. To manually start or stopping drying, tap Drying button in the app.

Notes:

• Drying duration is 2 hours by default and you can modify this in the app.
• Auto drying can be disabled through the app.

Charging
After cleaning, the robot will automatically return to the dock to charge.
In Pause mode, press the button to send the robot back to the dock. The power indicator will pulse as the robot charges.

DND Mode
The default Do Not Disturb (DND) period is from 22:00 to 08:00. You can use the app to disable the DND mode or modify the DND period. When DND mode is activated, the robot will not automatically resume cleanup, the power indicator light will dim, and the volume of the voice prompts will lower.

Child Lock
Press and hold the button to enable/disable the child lock. You can also set it in the app. Once enabled, the robot will not react to button presses when it is stationary. When the robot is cleaning or docking, press any button to stop it.

Error
If an error occurs, the power indicator and status indicator light will flash red and a voice alert will sound.

Notes:

• The robot will go to sleep automatically if left in a malfunctioning state for over 10 minutes.
• Placing a malfunctioning robot on the dock manually will end the current cleanup.

System Reset
If the robot does not respond when a button is pressed or cannot be turned off, reset the system. Press the Reset button, and the robot will reset automatically.
Note: After resetting the system, scheduled cleaning, WiFi, etc. will be restored to factory settings.

Restore Factory Settings
If the robot does not function properly after a system reset, switch it on. Press and hold the button and at the same time, press the Reset button until you hear the “Restoring factory settings” voice prompt. The robot will then be restored to factory settings.

Routine Maintenance

Main Brushes
* Clean every 2 weeks and replace every 6-12 months.

1. Main Brushes
2. Main Brush Cover
3. Latches
4. Main Brush Bearing
5. Main Brush Caps
6. Turn over the robot and press the latches to remove the main brush cover.
7. Remove the main brushes and pull out the main brush bearing.
8. Pull out the main brush caps.
9. After removing the tangled hair or dirt at both ends of the main brushes, reinstall it.
10. Press on the main brush cover to lock the brush in place.

Notes:

• Main brushes should be wiped down with a wet cloth and left to dry away from direct sunlight.
• Do not use corrosive cleaning fluids or disinfectants to clean the main brushes.

Side Brush
Clean monthly and replace every 3-6 months.

1. Unscrew the side brush screw.
2. Remove and clean the side brush. Reinstall the brush and tighten the screw.

Omnidirectional Wheel

1. Use a tool, such as a small screwdriver, to pry out the axle and take out the wheel.
2. Rinse the wheel and the axle with water to remove any hair and dirt. Dry and reattach the wheel, pressing it firmly in place.

Main Wheels
Clean the main wheels with a soft, dry cloth.

Dustbin

1. Open the top cover of the robot and press the dustbin latch to take out the dustbin.

2. Press the cover latch to open the dustbin cover and remove the washable filter, then empty the dustbin.

3. Fill the dustbin with clean water and close the cover. Gently shake the dustbin, and then pour out the dirty water.
   Note: To prevent blockage, only use clean water without any cleaning liquid.

4. Leave the dustbin and the washable filter to dry.

Washable Filter

1. Open the filter cover and remove the filter.
2. Rinse the filter repeatedly and tap it to remove as much dirt as possible.
3. Allow 24 hours for the filter to dry thoroughly and reinstall it.

VibraRise Mop Cloth
* Clean after each use and replace every 3-6 months.

1. Remove the VibraRise mop cloth from the VibraRise mop mount. Clean the VibraRise mop cloth and air-dry it.

Note: A dirty VibraRise mop will affect the mopping performance. Clean it before use.

Robot Sensors
Use a soft, dry cloth to wipe and clean all sensors, including:

1. Wall Sensor
2. Reactive 3D Obstacle Avoidance Sensor
3. Carpet Sensor
4. Cliff Sensors
5. Mop Wash Sensor

Charging Contact Areas
Use a soft dry cloth to wipe the charging contacts on the robot and the dock.

Battery
The robot is equipped with a built-in high-performance lithium-ion rechargeable battery pack. To maintain battery performance, keep the robot charged during normal use.
Note: If the robot will be left unused for a long period, turn it off and charge it at least every three months to avoid battery damage caused by over- discharge.

Moving the Dock
Remove the water tanks and the dustbin before moving the dock. Grip the handle on the back with one hand and the inner side of the front, as shown. Do not grip the base because it is not designed for lifting.

Dirty Water Tank
Clean the dirty water tank as needed. Open the dirty water tank lid and pour out the dirty water. Fill the tank with clean water, close the lid, lock it, and shake. Pour out the dirty water. Close the lid and then re-install.

High-Speed Maintenance Brush
Lift the high-speed maintenance brush latch and remove the brush, as shown below. Remove any entangled objects in the highspeed maintenance brush and rinse it clean. Reinstall the brush and latch it in place.

Water Filter
Unlock the water filter and remove it from dock. Unlock the filter latch, rinse the filter clean. Use a soft, dry cloth to wipe the cleaning tank, and then reinstall the filter. Press down the filter until you hear it lock with a click.

Replacing the Disposable Dust Bag

1. Lift the dustbin and remove the bag vertically as shown.
2. Discard the dust bag and clean around the filter with a dry cloth.
3. Slot in a new disposable dust bag as shown. Slide until it reaches the bottom of the slot and reinstall the dustbin securely.

Note: Always install a dust bag before putting back the dustbin top lid to avoid auto-emptying without the bag. You can also disable auto-emptying in the app.

Cleaning the Air Duct
Follow the following steps to clean the air duct and avoid blockages.

1. Remove the clean water tank, dirty water tank, and dustbin.
2. Remove the water filter and wipe off any water marks with a cloth.
3. Grasp the sides of the dock base upward to disassemble and turn it over to check any blockage.
4. Clean the air inlet with a cotton swab if it gets blocked and wipe it with a dry cloth.
5. Carefully place the dock upside down on a hard floor covered with a soft towel.
6. Unscrew the three screws and remove the cover.
7. Wipe the air duct and duct cover with a dry cloth.
8. Reinstall the cover and screw it back in place.

Basic Parameters

Robot

• Model S81USP
• Battery 14.4V/5200mAh lithium-ion battery
• Rated Input 20V 1.5A
• Charging Time Approx. 4 hours

Empty Wash Fill Dock

• Name Empty Wash Fill Dock
• Model EWFD07LRR, EWFD08LRR
• Rated Input Voltage 120V~
• Rated Frequency 60Hz
• Rated Input (Dust Collection) 9.5A
• Rated Input (Non-Dust Collection) 1.2A
• Rated Output 20V 1.5A
• Charging Battery 14.4V/5200mAh lithium-ion battery

Common Issues

Robotic Vacuum Cleaner
Product Model: S81USP
Manufacturer: Beijing Roborock Technology Co., Ltd.
Address of Manufacturer: Floor 6, Suite 6016, 6017, 6018, Building C, Kangjian Baosheng Plaza, No.8 Heiquan Road, Haidian District, Beijing, P.R. CHINA

For more product information, visit our website: www.roborock.com
For after-sales support, contact our support team at: support@roborock.com (United States/Canada/Non- Europe)
1-855-960-4321 (United States only)
1-833-421-1915 (Canada only)

References

• Register a .EU.COM domain today!
• Roborock US Official Store | Intelligent Robot Vacuum Cleaner and Mop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>