TOPBAND TA1 360 Area Light User Manual

360 Area Light
**User Manual

**

General Specification

Features

• High efficiency LED source. 4 settings & stepless dimming.
• RF remote control. Support the controlling from any directionand within 15m distance.
• Support 360° all-round mode and 180° energy-saving mode.Optimize the light power.
• Dual power source: 110V-240V AC adapter & built-in batteryMax 50W fast charge & discharge function by USB-C port
• Memory setting  function. Maintain the setting of last time  when turn on the light.

Operating Instructions

Operating Instructions
Main switch

| ON / OFF| Turn on/off with long press for 0.5 seconds
---|---|---
LUMEN| Switch to 180° mode or 360° mode with single click
300lm→1000lm→3000lm→6000lm with single click

Remote controler

| ON / OFF| Turn on/off with long press for 0.5 seconds
---|---|---
Switch to 180° mode or 360° mode with single click
+ button| 300lm→1000lm→3000lm→6000lm with single click
long press for stepless
– button| 6000lm→3000lm1000lm→300lm with single click
long press for stepless

*The remote control can only be used when the remote control indicator is on(blue).
Power indicator

| 4 Leds on| Battery capacity > 75%
---|---|---
3 Leds on| 75% > Battery capacity > 50%
2 Leds on| 50% > Battery capacity > 25%
1 Led on| 25% > Battery capacity > 15%
1 Led flashing| 15% > Battery capacity

Declaration of conformity

This product complies with the radio interference requirements of the European community. Hereby, Shenzhen Topband Co., Ltd declares that the product is in compliance with the essential requirements and other relevant provisions of RE Directive
2014/53/EU.
FCC ID: 2ADDWTA1
FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1)This device may not cause harmful interference.
   (2)This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
IC : 23804-TA1
ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment should be installed and operated with a minimum distance of 10 cm between the radiator and your body determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Shenzhen Topband Co.,Ltd
Topband Industrial Park,Liyuan Industrial Zone, Shiyan Town Baoan District,Shenzhen,China
www.topband.com.cn/en
Phone:+86-755-27551888-8223

References

• TOPBAND Leading Inteligent Electronic Controller Solutions Provider

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>