TECNO SPARK10 Pro Smartphone User Manual
- June 12, 2024
- TECNO
Table of Contents
TECNO SPARK10 Pro Smartphone
Product Information
The TECNO SPARK 10 Pro is a smartphone featuring a 6.78-inch HD+V/MDT Panda/BlackINCELL assembly display. It comes with a front camera, volume keys, power key with a side fingerprint sensor, earphone jack, USB port, and NFC functionality. The device is powered by HiOS, which runs on AndroidTM OS. It meets the government’s requirements for Specific Absorption Rate (SAR) and complies with Part 15 of the FCC Rules.
Features
- 6.78-inch HD+V/MDT Panda/BlackINCELL assembly display
- Front Camera
- Volume +key and Volume -key
- Power key with a side fingerprint sensor
- Earphone jack
- USB port
- NFC functionality
- HiOS running on AndroidTM OS
Product Usage Instructions
SIM/SD Card Installation
- Power off the mobile device.
- Refer to the picture provided in the user manual for SIM/SD card installation.
Charging the Phone
You can charge your TECNO SPARK 10 Pro using a charger or by connecting it to
a computer using a USB cable (included with the phone).
Note: Only use the TECNO charger and cables to avoid damaging the device
and invalidating the phone warranty.
FCC Caution
The TECNO SPARK 10 Pro complies with Part 15 of the FCC Rules. Please note the following:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Trademark: AndroidTM is a trademark of Google LLC.
Explosion diagram specification
1| 6.78HD+V/MDT
Panda/BlackINCELL
assembly
| 2| LCM CONDUCT FOAM 2
---|---|---|---
3| LCM CONDUCT FOAM 1| 4| REC DECO
5| FRG FRAPHITE| 6| FLASH MYLAR
7| P_SENSOR MYLAR| 8| FCAM SEAL FOAM 1
9| FCAM SEAL FOAM 1| 10| FCAM SEAL FOAM 1
11| PL GUIDE| 12| SIDEKEY FPC CONDUCT
13| SIDEKEY FPC CONDUCT| 14| PL RUBBER
15| ADHESIVE FLASH| 16| ADHESIVE P SENSOR
17| WATERPROOF FOAM| 18| WATERPROOF MEMBRANE
19| SIDEKEY FPC| 20| SIDEKEY FPC
21| REC FOAM| 22| REC FOAM
23| CONDUCTIVE SPONGE| 24| SIM FOAM
25| AD9 H831 FCAM| 26| BAT ADHESIVE 1
27| Receiver| 28| COAXIAL
29| REC FPC| 30| PCBA
31| SCREW| 32| Main Back cam
33| FRO CAM PRESS FOAM| 34| VICE CAM
35| VICE CAM| 36| CARD DOO
37| MAIN CAM FOAM| 38| FLA GUL ADHESIVE
---|---|---|---
39| FLA GUIDE| 40| REAR CAM COPPER FOIL
41| FLA GUL FOAM| 42| MAIN CAM LENS ADHESIVE
43| VICE CAM LENS ADHESIVE| 44| FLA LENS ADHESIVE
45| MAIN CAM LENS| 46| MAIN CAM LENS
47| BAT PORON| 48| RF SHIELD GRAPHITE
49| FLA PCB GRAPHITE| 50| FLA PCB GRAPHITE
51| SCREW| 52| CHARGER SHIELD GRAPHITE
53| CHARGER SHIELD GRAPHITE| 54| CHARGER SHIELD GRAPHITE
55| BAT GRAPHITE| 56| PEAR
57| FG BTB PRESS FOAM| 58| VICE CAM BTB PRESS FOAM
59| VICE CAM BTB PRESS FOAM| 60| VICE CAM SUPPORT FOAM
61| BATTERY BTB PRESS FOAM| 62| BATTERY BTB PRESS FOAM
63| ANT MAIN| 64| FINGER
65| FINGER| 66| SPK FPC
67| MOTO| 68| SUB PCBA
69| SCREW| 70| SCREW
71| LCM FPC ADHESIVE| 72| BAT ADHESIVE 3
73| SCREW| 74| BOX
75| SPEAKER FOAM| 76| JACK RUBBER
77| JACK RUBBER| 78| USB RUBBER
79| SPEAKER RUBBER| 80| USB CONDUCT FOAM
81| SPEAKER CONDUCT FOAM| 82| MIC RUBBER
83| MIC FOAM| 84| SPEAKER NET
85| FRP HSG| 86| WATERPROOF MALAR
Know your phone
- Front camera
- Volume +key
- Volume -key
- Power key & side fingerprint sensor
- Earphone jack
- USB port
- NFC
SIM/SD card installation
- Power off your mobile.
- Refer to the following picture for SIM / SD card installation.
Charging the phone
You can charge your device using a charger or by connecting it to the computer
using a USB cable (comes with the phone). Use only TECNO charger and cables.
Other chargers or cables may damage the device. This will invalidate your
phone warranty.
FCC Caution
Labeling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluations
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health. FCC
RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6
W/kg averaging over one gram of tissue. Device types: KI7 (FCC ID: 2ADYY-KI7)
has also been tested against this SAR limit. The highest SAR value reported
under this standard during product certification for use at the ear is
1.320W/kg and when properly worn on the body is 0.603W/kg. This device was
tested for typical body-worn operations with the back of the handset kept 10
mm from the body. To maintain compliance with FCC RF exposure requirements,
use accessories that maintain a 10 mm separation distance between the user’s
body and the back of the handset. The use of belt clips, holsters, and similar
accessories should not contain metallic components in its assembly. The use of
accessories that do not satisfy these requirements may not comply with FCC RF
exposure requirements and should be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 1.0 cm must be
maintained between the user’s body and the handset, including the antenna.
Third-party belt-clips, holsters, and similar accessories used by this device
should not contain any metallic components. Body-worn accessories that do not
meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or approved antenna.
HiOS runs on AndroidTM OS. Android is a trademark of Google LLC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>