Kessil A500X Tuna Blue User Manual
- June 4, 2024
- Kessil
Table of Contents
LED Aquarium Lighting
A500X
Tuna Blue USER MANUAL
INSIDE THE BOX
PARTS DIAGRAM
A | Power Cord |
---|---|
B | Intensity Tuning Knob |
C | Screw Hook |
D | Hanging Ring |
E | Hanging Bracket |
F | Color Tuning Knob |
G | K-Link Ports |
H | Venting Holes |
I | Reflector-55 |
INSTALLATION
Step 1 Power
Connect the A500X to the power adapter and plug it into a wall outlet. Turn
the Intensity Tuning Knob (B) to the right to turn on the light.
Step 2 Control
- Turn the Intensity Tuning Knob (B) to adjust the brightness of the fixture.
- Turn the Color Tuning Knob (F) to adjust the light to the desired color.
- A500X can be connected and controlled through Kessil Spectral Controller X with a K-Link Cable, or through the WiFi Dongle with iPhone or Android phone app.
Step 3 Controlling Multiple A500X
- Connect two or more lights with K-Link Cables as shown in the image.
- Multiple A500X lights can be controlled by either manually, an external controller, or the WiFi Dongle.
- When controlling without an external controller or WiFi Dongle, tuning controls on any light control all other lights in chain.
Push the K-Link Cable connector or WiFi Dongle down to make sure the connection is firm.
Step 4 Mounting
- Screw the Hanging Ring (D) into the center screw hole.
- Hang the light with the two Screw Hooks (C) and the two Hanging Brackets (E).
- To install the Hanging Brackets (E), remove the screws on the A500X, use the same screws to secure the fasteners with triangular rings onto the light fixture.
Step 5 Reflector-55
The complementary Reflector-55 narrows the beam of the light to increase the
light intensity and penetration and to avoid overspilling.
CAUTION
HOT SURFACE. DO NOT TOUCH WHEN THE LIGHT IS ON & WITH REFLECTOR ACCESSORIES
OPTIONAL ACCESSORIES
MAINTENANCE
- Keep the fan and Venting Holes (H) clear of dust. To clean the fan, unplug the unit and insert the tip of a CO2 dust blower (or similar dust blower) in one of the venting holes for the Fan. Hold and spray. You can also gently vacuum out the dust through the venting holes.
- Keep the LED array and Reactor-55 (I) clean. If the array lens and reactor become contaminated with water, dust, or other particles, unplug the unit and clean them with isopropyl alcohol. Wet a cotton swab or a napkin in isopropyl alcohol, gently wipe the surface and let it dry.
- Keep plastic covers for K-Link Ports (G) plugged in when the ports are not in use. Keep the ports clean all time.
TROUBLESHOOTING GUIDE
Please make sure to perform maintenance before doing any troubleshooting.
Problem | Cause / Solution |
---|---|
Light doesn’t turn ON | Make sure the unit is connected to the power adapter |
and the power adapter is plugged into an outlet with the correct
specifications.
Make sure the power adapter has the right specifications.
Make sure electrical power is available to the AC outlet being used.
Make sure the device is operating within the specified operating temperature
range. If unit overheats, it will automatically shut down.
Unit is flickering| Make sure the power adapter has the right specifications.
Make sure the unit has not overheated by operating at a room temperature above
100°F/40°C.
Make sure the fan is operating properly.
SPECIFICATIONS
Unit Dimensions and Weight
Dimensions| Ø5.23” x 3.68” (Ø13.3 cm x 9.36 cm)
Weight| 1.72 Ibs (0.78 kg)
illuminator| Power Adapter
Power Consumption| 185W maximum| Input| 100-240V~ AC 50-60 Hz
Input Voltage| 48V DC 5%| Output| 48V DC, maximum 4.2A
SAFETY INSTRUCTIONS
- Caution: Misuse of this device contrary to these instructions may result in physical injury or damage to the product.
- DO NOT use a power adapter outside of the specifications. This is a fire hazard and may lead to unit failure.
- DO NOT use outdoors. This unit is intended for indoor use only.
- DO NOT expose unit to an extremely humid environment or submerse unit in water. This may lead to unit failure.
- DO NOT place the working illuminator in close contact with any objects. This may cause objects to heat up and the unit to overheat.
- KEEP LED array away from sharp objects. Sharp objects may break the array lens and lead to unit failure.
- DO NOT cover or place objects on the power adapter. Power adapter should not be contained in an airtight space.
- DO NOT block or cover the Venting Holes (H). This may cause the device to overheat and lead to failure.
- ENSURE that the light is correct and securely mounted.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 8 inches (20cm) between the radiator & your body.
Kessil Lighting A DiCon Business Division 1689 Regatta Blvd, Richmond, CA
94804 510-620-5250
Kessil.com
kessil.Ied
kessiltube
@kessil I11
@kessilled 1:21
**K**
kessil.com
This is a LED light source emitting 40 % or more of total radiation power of
the range 250-800 nm in the range of 400-480 nm, and is intended for coral
growth.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>