joie i-Gemm Pavement Baby Car Seat Instruction Manual

: June 12, 2024
: Joie

Table of Contents

i-Gemm™ 3/i-Juva™ /i-Snug™ 2/i-Jemini™
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

i-Gemm™ 3/i-Juva™ /i-Snug™ 2/i-Jemini™

attachment to i-Base Advance

Instruction Manual

ECE R129/03
i-Size universal ISOFIX

Welcome to Joie™

You have purchased a high quality, fully certified child safety child restraint. This product is suitable for the use of your child with height and weight according to the following:

i-Gemm 3: child height 40cm – 85cm/ child weight13kg
i-Juva: child height 40cm – 75cm/ child weight13kg
i-Snug 2: child height 40cm – 75cm/ child weight13kg
i-Jemini: child height 40cm-85cm/ child weight13kg

Keep this instruction manual for future reference. Carefully read this Instruction Manual and follow the installing steps because this is the ONLY way to protect your child from serious injury or death in case of an accident, and to provide comfort to your child while using this product.

! IMPORTANT: KEEP FOR FUTURE REFERENCE.
PLEASE READ CAREFULLY.

Please keep the instruction manual in the storage compartment at the bottom of the base as right figure.
or
Please keep the instruction manual at the bottom of the soft goods.

joie i-Gemm Pavement Baby Car Seat C1

Parts List

Please make sure there are no missing parts. Please contact the retailer if anything is missing.

Recline Adjustment Button
Enhanced Child Restraint Latched Indicator
Enhanced Child Restraint Release Button
Load Leg Adjustment Button
Load Leg
Load Leg Indicator
Rebound Bar
ISOFIX Releasing Button
ISOFIX Connector
ISOFIX Guides

WARNING

! For the complete information and best protection of using the enhanced child restraints, you must follow their instruction manuals carefully:

Please refer to i-Gemm 3 instruction manual for the use of i-Gemm 3.
Please refer to i-Juva instruction manual for the use of i-Juva.
Please refer to i-Snug 2 instruction manual for the use of i-Snug 2.
Please refer to i-Jemini instruction manual for the use of i-Jemini.

Emergency

In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

Installation with base

This is an i-Size Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’ manual.
If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.

Materials Plastics, metal
Patent No. Patents pending

Concerns on Installation

Installation with base

see images 1 – 13

Please remove the the rebound bar first when used with the enhanced enhanced infant child restraint, and store it safely for use later with i-Venture seat. Do not remove the rebound bar when attaching i-Juva to the base.

Unfold the load leg from storage compartment. 1
Fit the ISOFIX guides with the ISOFIX anchor points. 2 The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.
If base used previously with i-Venture seat, remove rebound bar as shown in illustration 3
! Store safely for future use with i-Venture seat. 4
Press the ISOFIX release button on either side of the base, then pull out the ISOFIX connectors. 5
Line up the ISOFIX connectors with the ISOFIX guides, and then click both ISOFIX connectors into the ISOFIX anchor points. 6
! Check to make sure the base is securely installed by pulling on the both ISOFIX connectors.
There are 9 adjustable positions for ISOFIX. Press the ISOFIX release button and push the base back against the vehicle seat until tight.
After placing the base on the vehicle seat, extend the load leg to floor 7 , When the load leg indicator shows green means it is installed correctly, red means it is installed incorrectly. 7 -1
! The load leg has 24 positions. When the load leg indicator shows red this means the load leg is in the wrong position.
! Make sure the load leg is in full contact with the vehicle floor pan.
! Squeeze the load leg releasing button, then shorten the load leg upwards.
The completely assembled base is shown as 8
! The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. 8 -1
! The load leg must be installed correctly with green indicator. 8 -2
Push the enhanced enhanced infant child restraint down into the base 9 , if the enhanced infant child restraint is secure, the enhanced infant child restraint indicator shows green. 10
! Press the recline adjustment button, and adjust the enhanced infant child restraint to the proper position. There are 7 recline angles with rearward facing mode.
! The most convenient way to install the enhanced infant child restraint is when the base is in the 7th position.
! Pull up on the enhanced enhanced infant child restraint to be sure it is securely latched into the base.
To release the enhanced enhanced infant child restraint, pull the enhanced enhanced infant child restraint up while squeezing the enhanced enhanced infant child restraint release button. 11
To remove the base, press the secondary lock button first and then the button on the ISOFIX connectors before removing the base from the vehicle seat. 12
Press the ISOFIX release button to store the ISOFIX. 13