dji RM220 RC Motion 2 Controller User Guide
- June 12, 2024
- DJi
Table of Contents
RM220 User Guide
Overview
-
Battery Level LEDs
-
Lock Button
Press twice: start the motors of the aircraft. Press and hold to make the aircraft automatically take off, ascend to approximately 1.2 m, and hover. Press and hold while hovering to make the aircraft automatically land and the motors to stop. -
Joystick
Use the joystick to control the aircraft to move in the direction relative to the center of the FPV view. -
Mode Button
Press once to switch between Normal and Sport mode. -
Shutter/Record Button
Press once to take photos or start or stop recording. Press and hold to switch between photo and video mode. -
Accelerator
Press to fly the aircraft in the direction of the circle in the goggles.
Push the accelerator out to fly the aircraft backward.
Apply more pressure to accelerate. -
Dial
Toggle to control the camera zoom in or out. When used with DJI goggles, press the dial to open the goggles menu on the FPV view, then toggle the dial to navigate the menu or adjust parameters, and press to select or confirm. Long press the dial to exit the current menu. -
USB-C Port
For charging or connecting the motion controller to a computer to update firmware. -
Power Button
Press once to check the current battery level. Press once then again and hold to power the motion controller on or off.
Using for the First Time
-
Charging
-
Powering on
Check battery level: press once.
Power on/off： press then press and hold. -
Linking
The aircraft must be linked with the goggles before the motion controller. Make sure that all devices are powered on before linking.
a) Press and hold the power button of the aircraft until the battery level LEDs start to blink in sequence.
b) Press and hold the power button of the motion controller until it beeps continually and the battery level indicators blink in sequence.
c) The motion controller stops beeping when linking is successful and both the battery level indicators turn solid and display the battery level. -
Activation
Power on the aircraft, goggles, and motion controller. Make sure all the devices are linked. Connect the USB-C port of the goggles to the mobile device, run DJI Fly, the motion controller will be activated automatically.
Control the aircraft
Tilt left or right or rotate the motion controller to rotate the aircraft.
Tilt the motion controller up and down to control the tilt of the gimbal.
Tilt the motion controller 90° up or down, then press the accelerator to make
the aircraft ascend or descend.
Press the accelerator to fly in the direction of the circle in the goggles.
Push the accelerator out to fly the aircraft backward.
Specifications
| Model Number | RM220 |
|---|---|
| Max Transmission Distance (unobstructed, free of interference) | 10 km (FCC), 6 |
km (CE/SRRC/MIC)
Operating Frequency| 2.400-2.4835 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)| 2.4 GHz: <28.5 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.8
GHz: <31.5 dBm (FCC), <19 dBm (SRRC), <14 dBm (CE)
Operating Temperature| -10° to 40° C (14° to 104° F)
Built-in Battery Type| Li-ion
Battery Chemical System| LiNiMnCoO2
Compliance Information
FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI Motion Controller 2
Model Number: RM220
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above
mentioned model was tested to demonstrate complying with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The aircraft complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm during normal operation. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
This remote controller device complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End user must follow the specific
operating instructions for satisfying RF exposure compliance. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
The portable device is designed to meet the requirements for exposure to radio
waves established by the Federal Communications Commission (USA). These
requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The
highest SAR value reported under this standard during product certification
for use when properly worn on the body.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference.(2)This device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment complies with RSS‐102 radiation exposure limits set forth for
an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter. The portable device is designed to meet the requirements for
exposure to radio waves established by the ISED.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of
tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this
device(DJI Motion Controller 2) is in compliance with the essential
requirements and other relevant provisions of the Directive 2014/53/EU. A copy
of the EU Declaration of Conformity is available online at www.dji.com/euro-
compliance EU contact address: DJI GmbH,
Industriestrasse 12, 97618, Niederlauer, Germany
Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this
device(DJI Motion Controller 2) is in compliance with the essential
requirements and other relevant provisions of Radio Equipment Regulations
2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com
/euro-compliance
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances
is responsible to bring the appliances to these collecting points or to
similar collection points. With this little personal effort, you contribute to
recycle valuable raw materials and the treatment of toxic substances.
Brazil Warning message
Corpo SAR (10g) Brasil: X.XXX W/kg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>