RHINO-RACK 571 Rear Loading Kayak Carrier User Guide
- June 13, 2024
- RHINO RACK
Table of Contents
RHINO-RACK 571 Rear Loading Kayak Carrier
Important: Please read these instructions carefully prior to installation. Please refer to your training instructions to ensure that the kayak carrier is installed in the correct locations. Check the contents of the kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle’s glove box after installation is complete.
Important Information
Maximum carrying capacity: Refer to the maximum carrying capacity of roof racks Please refer to your vehicle manufacturer’s handbook for the maximum carrying capacity of your roof racks. Always use the lower of the two figures. The load must be evenly distributed over the crossbars. Warning: Do not attempt to fit the 571/ 581 to your vehicle unless you fully understand these fitting instructions. Please direct any questions regarding fitting to the dealer from where the 571/ 581 was purchased. Use only non-stretch fastening ropes or straps. Ensure the bottom of the kayak is clean before loading to avoid damage to both the kayak and cradle. Take care when loading and unloading to ensure that the kayak does not damage the vehicle. The roof racks must be at least 600mm apart for safe use. Failure to follow these warnings and instructions will void the warranty.
Recommendations
It is essential that all bolt connections be checked after driving a short
distance when you first install your kayak cradles. Bolt connections should be
checked again at regular intervals (once a week is enough, depending on road
conditions, usage, loads, and distances traveled). You should also check the
roof racks and kayak cradles each time they are re-fitted. Always make sure to
fasten your load securely. Please also ensure that all loads are evenly
distributed and that the center of gravity is kept as low as possible. Long
loads (e.g. canoes and kayaks) must be secured front and rear with non-stretch
fastening ropes or straps. Roof racks must be removed when putting the vehicle
through an automatic car wash.
Caution : The handling characteristics of the vehicle change when you
transport a load on the roof. For safety reasons, we recommend you exercise
extreme care when transporting wind-resistant loads. Special consideration
must be taken into account when cornering and braking.
Note for Dealers and Fitters
It is your responsibility to ensure this fitting instruction is given to the
end user or client
Rhino-Rack
3 Pike Street, Rydalmere, NSW 2116, Australia. Document No: R234 Fit Time:
15min
(Ph) (02) 9638 4744 Prepared By: Andy Wana Issue No: 04
(Fax) (02) 9638 4822 Authorised By: Chris Murty Issue Date: 29/08/2017
These instructions remain the property of Rhino-Rack Australia Pty Ltd and may
not be used or changed for any other purpose than intended.
When these roof racks are to be used on a vehicle that is driven off sealed
roads The maximum load rating must be divided by 1.5. Remember to subtract the
weight of the roof racks to
determine your maximum permissible load capacity.
WARNING! Important Load Carrying Instructions
With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicles can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy. Instead, rigidly fi x to either the cabin roof racks or the canopy roof racks.
Paddle/ Surfboards should be fixed to the front of the vehicle
Parts List
571
Item| Component Name| Qty| Part
1| M6 x 40mm Security Head Screw| 8| B085
2| M6 Flat Washer| 8| W003-BLK
3| Front Cradle Rest| 2| M598
4| Rear Cradle Slide| 2| –
5| Glide Moulding| 2| –
6| Hinge Pin Long| 1| –
7| Kayak Carrier Arm| 4| M594
8| Kayak Carrier Base| 4| M596
9| Hinge Pin Short| 1| –
10| Lower Clamp| 4| M530
11| M6 Nyloc Nut| 8| N022-BLK
12| 5.5m Tie Down Strap| 2| –
13| Allen Key| 1| H002
14| 3m Covered Buckle Strap| 2| –
15| Instructions| 1| R234
581
Item| Component Name| Qty| Part
1| Locking Cover| 4| M600
2| M6 Nyloc Nut| 4| N022-BLK
3| Turn Wheel| 4| M599
4| M6 Flat Washer| 4| W003-BLK
5| Front Cradle Rest| 2| M598
6| Rear Cradle Slide| 2| –
7| T-bolt M6 x 30mm| 4| B183
8| 5.5m Tie Down Strap| 2| –
9| 3m Covered Buckle Strap| 2| –
10| Keys| 2| –
11| Glide Moulding| 2| –
12| Kayak Carrier Arm| 4| M594
13| Hinge Pin Short| 4| –
14| Kayak Carrier Base| 4| M595
15| Hinge Pin Long| 4| –
16| Fitting Instructions| 1| R234
Care Instruction
Wash and clean vehicle roof racks prior to fitment
571 Fitting Instructions
- Loosely attach one side
- With one side attached, position cradles over the FRONT cross bars
- Securely tighten screws with the Allen key supplied
- Loosely attach one side
- Securely tighten screws with the Allen key supplied
- Load the kayak onto the REAR cradles. It may be necessary to readjust the position to ensure it fits securely
- Make sure the kayak is in line with the vehicle as shown
- Straps should always pass under the crossbar as shown
581 Fitting Instructions
Insert T-bolts into the channel and tighten dials
Load the kayak onto the REAR cradles. It may be necessary to readjust the position to ensure it fits securely
Straps should always pass under the crossbar as shown
Documents / Resources
|
RHINO-RACK 571 Rear Loading Kayak
Carrier
[pdf] User Guide
571 Rear Loading Kayak Carrier, 571 Rear Loading Kayak Carrier, Rear Loading
Kayak Carrier, Loading Kayak Carrier, Kayak Carrier
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>