TiramisuBest JT-326S Basketball Stand Instruction Manual

TiramisuBest JT-326S Basketball Stand

WARNING
PROPER INSTALLATION OF SWINGING ON THE RING CAUSES SERIOUS INJURY AND DEATH.

Notice to assemblers
All the basketball systems, including those used for displays, must be assembled and ballasted according to instructions. Failure to follow instructions could result in serious injury. Please read all warnings and cautions before assembly. It is recommended to supervise children as they play with this product. This product is to be assembled by 2 adults only! We appreciate your purchasing one of our many fine products. We are assured that you will be very satisfied with your selection.

Assembly Steps

1. Open the carton, and find out all the parts listed on page 3, two adults are required for assembly.
2. Fix ring(2)and connect plate(24) on board(1 ) with bolts(5) and nuts(6), After that, use bolts(7)to fix the top of board bracket(4)on the back of board (1 )tightly. Insert the top pole(11 )into the connecting plate(24). then fix top pole(11) and connect plate(24) and the end of board bracket(4) by bolts(8)and nuts(9).
3. Fix the top pole(11) and middle pole(12) together by 2 pcs of bolt (22) and 2 pcs uts (23).
4. Place the base(14)on a chosen playing ground, the surface beneath the base should be horizontal. Insert the wheel shaft(15 )into wheel (16), base(14), and end of the bottom pole (13) orderly.
5. Fix one end of the 2pes pole braces (19) on a bottom pole(13)by bolt(17 )and nut(18). Then fix another end of the 2pcs pole braces (19)on base(14)by bolt(20)and nut(21).
6. Fix the middle pole(12) and bottom pole(13)together by 2 pcs bolt (22) and 2 pcs nuts (23).
7. Tighten all the nuts, Filling the base with water or sand as below:

WHEN USING WATER

• Place the base on a smooth surface only! Without gravel or other sharp objects which could puncture the base and cause leakage.
• Check the base frequently for cracks and punctures.
• Always check the water level before the game. If a leak is found or the water level is low, lay the system onto the ground so that it can’t tip over.
• Add a tablespoon of chlorine bleach to the water each time the base is filled with water. This prevents algae from forming inside the base.

Moving the system

• The system should be moved by at least 2 adults capable of handling its weight
• Children should not be allowed to move the system.
• Stand in front of the system and pull the pole forward until the system is balanced on its wheels.
• Move the system to the desired location and carefully set the base down

WARNING
FAILURE TO COMPLY WITH THESE WARNINGS COULD RESULT IN INJURY.

1. Never hang from the rim or climb on the pole as injury or property damage could occur. For these reasons do not perform dunking the activities on this system as it is not designed for such use. Do not allow children to climb on the basketball system.

2. Never leave the unit assembled without weight in the tank.

3. Check the base frequently for leaks or loose caps. Slow leakage could cause the system to tip over unexpectedly and damage the floor if used inside. Seat the pole sections properly. Not doing so might allow the pole sections to separate
   during play or during transportation for this system.

4. Further, check before each use if all fittings and hardware are tight

5. Climate, corrosion, or misuse could result in system failure.

6. This system is not intended for children 3 and under.

7. All payers must use sufficient guards when playing.

POLE CARE AND SYSTEM MAINTENANCE

The life of your basketball system depends on many variables. The climate, exposure to corrosives such as salt, pesticides, or herbicides, and excessive use or misuse can all contribute to pole failure, which may cause property damage or personal injury. Check your basketball system frequently for loose hardware, excessive wear, and signs of corrosion. For safety reasons and to prolong the life of your basketball system, you must take the following preventive measures:
Check all nuts and bolts. If any are loose, tighten them. Check all pole sections for visible rust, chipped, or cracked paint. If either is present, do the following:

1. Use an emery cloth to completely remove any rust or chipped paint.
2. Clean the area with a damp cloth and allow it to dry.
3. Apply two coats of rust-preventative, high-gloss enamel to the area. Allow the paint to dry between two coats.

COOL INDUCTIVE LED FOR BASKETBALL RING

Brief Introduction
This led product is the auxiliary device of the basketball frame. It presents different cool lighting effects according to different scoring methods, adding a more interesting and fun sports atmosphere for pitchers.

Product function
Normal state: In the non-inductive state, there are two states: low brightness white light and no light, controlled by the plug-in power supply. Plug in the power supply, and the light is always an ice-blue color. If the light is off after 3S, it will be off when it is not normally sensed; Plug in the power supply, and the light is always bright ice blue. If the light is low bright white after it will be low bright white when it is not normally sensed. Box goal: basketball vibration ball frame into the net. 12 cool lighting effects, in turn, each mode lights last 3S; Through the heart goal: always in ice blue color for 35.
Note: the effective induction time of two goals should not be less than 25.

Product Parameter
Work voltage: DC4.5V (3PCS AA dry batteries)
Work current: The maximum current is 500mA when the induction lamp is on for 35.

Product installment
Product general assembly diagram.

1. surround the LED light belt around the basketball metal frame with the light bead facing out, Try to keep the light strip on the lower edge of the basketball hoop to reduce the probability of basketball impact, and assembly.
2. Two sides of 3M adhesive tape with one side pasted with the induction control box.
3. Place the other side flat on the bottom of the basketball hoop and the backboard, in the middle of the position, and try to keep the sensor and the hoop as far away as possible to prevent misjudgment caused by brushing the frame.
4. Stick the battery box to the basketball frame post with 3M tape.
5. Press the switch, and the LED can work normally.
   Tips: If you do not use this product, please turn off the battery box switch to prevent self-power consumption.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>