AVMAGIC A128 Helmet Bluetooth Headset Instructions

June 14, 2024
AVMAGIC

AVMAGIC A128 Helmet Bluetooth Headset Instructions
AVMAGIC A128 Helmet Bluetooth Headset

KEY INTRODUCTION

Product Overview

  1. Volume up
  2. Volume down
  3. Last number redial
  4. Multi-function key
  5. Headphone connector
  6. Switch
  7. Charging interface

OPERATING INSTRUCTION

Power on: In the power-off state, press and hold the ③ button for 3 seconds to power on, and the prompt will sounds “power on”.
Power off: In the power-on state, press and hold the ③ button for 5 seconds to shut down, and the prompt will sounds “power off”.
Clear pairing information: In the power-on state, press and hold the ⑤ key for 8 seconds to clear the pairing information and enter the pairing mode, and the red and blue lights flash alternately.
Pairing: After the headset is turned on, please turn on the Bluetooth of the mobile phone and search for “A128” to pair. If the phone has been connected to this headset before, when the headset is turned on and enters the pairing mode, it will automatically connect back to the phone. After the connection is successful, the blue light will flash once every 5 seconds.
Manually enter the pairing mode: In the connected state, press and hold the ⑤ key for 3 seconds to enter the pairing mode, and the red and blue lights flash alternately.
Switch between Chinese and English modes: Press and hold the ① and ② buttons at the same time for 2 seconds until you hear the prompt sound.
Volume up / down: Click the ① button to volume up, click the ② button to volume down.
Play / Pause: Click ⑤ button to play, click ⑤ button again to pause.
Previous song: When playing music, press and hold the ① button for 1 second to switch to the previous song.
Next song: When playing music, press and hold the ② button for 1 second to switch to the next song.
Voice Assistant: Click the ③ button to wake up the mobile phone voice assistant.
Answer the call: In the incoming call state, click the ⑤ button to answer the call.
Hang up the call: In the call state, click the ⑤ button to hang up the call.
Rejecting call: In the incoming call state, press and hold the ⑤ button for 3 seconds to reject the incoming call.
Switching to answer during a call: When a third party calls during a call, click the ④ button to switch to answer.
Switching to reject during a call: In the call state, when a third party calls, press and hold the ④ button for 1.5 seconds to reject the call.
Last number redial: When there is no call status, click the ④ button to redial the last number.
Cancel the outgoing call: After the outgoing call, click ⑤ button to cancel the outgoing call.
Automatically answer incoming call: press the ① and ② buttons at the same time to turn on/off this

function, and automatically answer the incoming calls without any operation for 5 seconds after turning on.

Battery Volume Indicators:

  1. When the battery is fully charged, the blue light will flash once every 5 seconds after connecting to the mobile phone.
  2. When the battery is low, there will be a “Battery low, please charge” prompt sound every 1 minute.
  3. When the battery is charging, the red light is always on.
  4. After the battery is fully charged, the red light goes out.

SPECIFICATION

Model: A128
Bluetooth version: V5.3
Battery capacity: 1000 mAh
Call time: 50 Hours (70% volume)
Music Time: 70 Hours (70% volume)
Charging time: 2 Hours
Bluetooth transmission distance: ≤12M
Voice Assistant: Support
Charging interface: Type-C interface
Charging input: DC 5V 1A
Smart microphone: Support
Net weight (main engine): About 44 g

PARTS LIST

  • Main engine

  • Headphone cable

  • Thin wire hard tube microphone

  • Thin wire microphone

  • Thin wire microphone

  • Clip type buckle

  • Host sticker

  • USB charging cable

  • 2 pairs of earphone speaker stickers

  • 2 microphone sponge covers

  • 2 square stickers

  • User Manual

EQUIPMINT INSTALLTION

Host installation:

Clean the area on the left side of the outside of the helmet. Wipe the shell of the helmet with a damp towel over this area. Wait for it to dry completely.

Stick-on buckle installation, tear off the double-sided adhesive isolation layer of the buckle, and stick the stick-on buckle to the installation position on the left edge of the helmet.

Installation Instruction

Clip-type buckle installation, find the installation position on the left edge of the helmet and clamp it, and then push it to a suitable position on the left side of the helmet.
Installation Instruction

Align the main unit with the card slot of the buckle base and push it from top to bottom, and the installation is successful when you hear the sound of the buckle.
Installation Instruction

Plug the headphone cable into the headphone jack of the host.

Installation Instruction

Install the headphone speaker:

Note: There are 2 speakers for the headphone cable accessory, the one with the shorter cable is the left speaker, please install it on the left side inside the helmet. The longer wire is the right horn, please install it on the right side inside the helmet

Peel off the isolation layer of the double-sided tape attached to the earphone speaker, and then paste it into the earphone hole reserved on the helmet.
Installation Instruction

Paste the headphone speaker on the headphone speaker sticker
Installation Instruction

Install the microphone:

Peel off the isolation layer with double-sided tape on the bottom, and stick it on the inner surface of the helmet.
Installation Instruction

Paste the microphone on the square sticker.
Installation Instruction

Adjust the head of the microphone to ensure that the sound hole of the microphone is near your mouth.

Align the interface between the main unit and the microphone cable, and then insert the microphone plug into the socket of the microphone cable.
Installation Instruction

Note: After installing the microphone, make sure to re-align the inner padding of the helmet.

USE ENVIROMINT

  1. The normal ambient temperature of the earphones is -40°C to +60°C, please do not exceed the temperature range; (2
  2. Do not expose the earphones to open flames to prevent explosion hazards; . Do not touch the earphones with sharp objects to prevent damage to the earphones;
  3. Please do not disassemble the earphone without permission;
  4. If the headset is not used for a long time, please keep the storage environment of the headset dry, and the device needs to be charged regularly for long term storage;

WARRANTY CARD

Warranty card

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals