MUHLER MLC-5045 Multicooker Instruction Manual

MUHLER MLC-5045 Multicooker

IMPORTANT SAFETY PRECAUTIONS

1. This appliance is for household use only.
2. The appliance must be plugged into a grounded socket outlet.
3. Never leave the appliance on or plugged into the socket outlet when not in use.
4. Never leave the appliance unattended when in use.
5. This appliance is not intended to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction. Children are being supervised not to play with the appliance.
6. Place the appliance on a horizontal, stable and heat-resistant surface.
7. Make sure that the mains voltage corresponds to the voltage shown on the marking plate of the appliance.
8. Do not connect the appliance in the same circuit where another appliance is connected.
9. Only the original accessories can be used with the appliance. Any other accessories not recommended by the manufacturer can result in hazards.
10. Do not operate the appliance without an internal or empty pot.
11. The Inner pot cannot be heated on a stove, or it will be damaged.
12. Do not put any food or water in when the inner pot has not been put in a host.
13. When the appliance is working, to avoid causing any danger, do not remove the inner pot away.
14. When using the appliance, steam may come from the air outlet. Keep hands and face away from the steam outlet avoiding scald.
15. Do not cover or put any object over the appliance. Keep the air outlets open to prevent any damage of the appliance.
16. Do not use the appliance in wet and heat environments.
17. Do not use the inner pot to wash rice and other ingredients to protect the pot from deformation and destroy the non-stick coating. The inner pot is treated with a non-adhesive coating, so it is not allowed to use hard or metal spoons or brushes.
18. Do not use the appliance if the inner pot is damaged.
19. Keep the inner pot, heater, and internal side of the appliance clean for the avoidance of over burning which may result in failure or other unforeseen accidents.
20. After putting the inner pot into the body, turn it the pot around in order to make sure is fitted well. If the inner pot is not put in or not well placed, it is not allowed to start cooking for avoid of any accidents.
21. To prevent food contact with the heating elements, do not overfill.
22. Clean the internal parts of the appliance after each use. Do not use any abrasive cleaners so to protect the coating from damage. Use a sponge and dish detergent to clean the parts.
23. Do not immerse the appliance in water or any other liquid. Clean the outer of the body with a damp cloth.
24. If the appliance or its power cord are damaged, do not use the appliance. The appliance must be sent for repair to an outraised service agent for checking and replacing the power cord.
25. If you are not going to use the appliance for a long time, unplug the appliance and store the power cord in its storage place. Make sure that the appliance is cooled and dried before storage. Store the appliance in its original box in a dry place.
26. Do not use the appliance if the plug, the power cord, or the appliance itself is damaged in any way.
27. If the power cord is damaged, you must have it replaced by the manufacturer, its service agent, or a similarly qualified person in order to avoid hazards.
28. Do not try to repair the appliance by yourself. There are no user-replaceable parts inside.
29. Keep the appliance and its power cord out of reach of children when it is in operation or in the cooling down process.
30. Keep the power cord away from hot surfaces. Do not plug in the power cord or operate the appliance controls with wet hands.
31. Never use the appliance with an external timer switch or a separate remote-control system.
32. do not let the cord hang over the edge of the table or counter surfaces.

cause burns. Particular attention has to be given where children and vulnerable people are present.

DESCRIPTION OF THE APPLIANCE

1. Steamer
2. Inner Pot
3. Out Pot
4. Body
5. Main Temp Control Apparatus
6. Pin
7. Cover Lid
8. Steam Hold
9. Keep Warm Lid
10. Water Holder
11. Control Plate
12. Heating Plate

ACCESSORIES

SPECIFICATIONS

The appliance is a class of protection against electric shock Class I

BEFORE USING FOR THE FIRST TIME

1. Read the instruction manual carefully and do it according to the indication of the IM
2. Please take out all parts, such as the non-stick inner pot, steam outlet, and detachable inner lid, and wash them before first use.
3. Please make sure there is no impurities in the bottom of the inner pot.
4. Make sure the inner pot is completely fit closely with the heating plate, rotating the inner pot.

CONTROL PANEL

1. Keep warm function
2. Interrupt the running process or clear previous settings

DISPLAY

1. When you choose the program, the light indicator of the function will light up.
2. When cooking, the LED display will show the remaining cooking time.
3. When finished, the LED display will show „00 00”, and keep warm automatically.

HOW TO USE

1. Take out the appliance from the box.
2. Remove all plastic packaging from the appliance.
3. Take out the all parts like the inner pot, steamer, and aluminum cover from the appliance and wash them with dishwasher detergent and sponge and leave them to dry completely.

NOTE

• Never use abrasive cleaning detergents or utensils to clean the inner pot to prevent the pot from deformation and damaging the nonstick coating.
• Add the Inner pot in the multicooker.

ATTENTION: Never use the appliance without the inner pot.

• Place the appliance on a horizontal, stable and heat-resistant surface.
• Take out the power cord from the storage compartment.
• Connect one side of the cord to the appliance power adapter and the other side, plug in into the grounded socket outlet.
• You will hear a beep signal, the display will show “ – – – – ” and all indicators will light up for a second. The appliance is going to stand-by mode and is ready for use.

ATTENTION

1. Never use the inner pot as a container in which to prepare cooking products. Always prepare the products in other containers and then add it to the inner pot.
2. Never use metal utensils to the inner pot. Always use plastic or wood utensils.

FUNCTIONAL BUTTONS

MENU

• When you turn on the multicooker, press the “MENU” button to select a program. Each time you press the button, you will go through the default programs. The indicator light will indicate which program you are on. After selecting the program, the LED display will show the default cooking time.

START BUTTON

• After you choose and set the program, press the “Start” button to start the cooking process.

TIMER/TEMP. BUTTON

• When you choose the program, you can press the “Timer/Temp.” button. to adjust the time or temperature by pressing the right or left arrow. Pressing the button ones, you can adjust the time, if you press the button 2ed time, you can adjust the temperature. The time or the temperature will appear on the LED display.

PRESET BUTTON

• Pressing the “Preset” button you are going to the time delay function.
• Pressing the ‘+’ or ‘-‘ button you can increase or decrees the time.
• Delayed start time is up to 24h at 1h intervals.

NOTE: The preset time is showing the start cooking time.

• In order to avoid bad taste of the food. The preset cannot be too long, it’s better not to exceed 12 hours.

Example

• Press the“Menu” button and go to the “Porridge”program, The default time is 1 hour. If you want to adjust the cooking time, press the “Preset” button, the indicator light is on. Adjust the time by pressing the ‘+’ or ‘-‘. buttons
• After set up the program, press the “Start” button to start the cooking process.

Note: If the delay time is less than the cooking time, the appliance will not enter the «Preset» function, it will work directly without preset settings.

KEEP WARM/CANCEL BUTTON

• The cooker will start to cook as you set and the display will show the cooking time.
• After the cooking process is finished, the cooker will enter to ‘keep warm’ function automatically.
• If you want to stop the cooking process and turn to keep warm directly when the cooker is working, press the „КЕЕР WARM/CANCEL” button, once to stop the cooking process. The appliance will cancel the cooking process and will go back to standby mode. The Display will show 00 00.
• Press the „КЕЕР WARM/CANCEL” button again to activate the ‘keep warm’ function.

SPECIAL PROGRAMMER FOR INTRODUCE

Fry program

• Press the ‘Menu” button and go to the “Fry’’ program. Press the “Start”, button to start the cooking process. The indicator light is on.
• After the cooking process is finished, the appliance will turn into ‘keep warm’ mode automatically. The indicator light is on.

Note

1. The oil shall not exceed the maximum indicated level.
2. In this program, the Preset function is not active. You can adjust the time and temperature of the cooking process only.

“DIY” function

• Press the ‘Menu’ button and go to the DIY program.
• If you want to change the default temperature and time, press the “Time/Temp.” button to adjust them.
• If you want to change the start cooking process press the ‘Preset’ button and adjust the time.
• After setup the program the “Start” button indicator light is on. Press the button to start the cooking process.
• After the cooking process is finished, if the temperature is over 80•C the appliance will turn into standby mode automatically.
• If the temperature is less than 80•C will switch to ‘keep warm’ mode.

Note: The cooking time and temperature can be changed after choosing the “DIY” program.

Express Program

• Press the ‘Menu’ button and go to the ‘Express’ program.
• After setup the program, the “Start” button indicator light is on. Press the button to start the cooking process.
• After the cooking process is finished, the appliance will turn into standby mode.

NOTE

1. The program is recommended for cooking grains.
2. The time indicator displays the «running serpentine» instead of the time value.
3. The «Express» program is automatically disabled after water boils off. No default time.

REHEAT Program

• Press the ‘Menu’ button and go to the “Reheat” program.
• After setup the program, press the “Start” button. The indictor light is on. After the cooking process is finished, the ‘keep warm” function will turn on automatically. The indicator light of the function will be on.

Rice Program

• Press the “Menu” button and go to the” Rice” program.
• After setup the program, press the “Start” button. The indictor light is on.
• After the cooking process finish, the ‘keep warm” function will turn on automatically. The indicator light of the function will be on.

Notes

1. The cooking time can be changed according to the voltage, rice capacity, water capacity, water temperature, rice quantity.
2. The maximum rice is 6 cups, suggesting the proportion of rice and water is 1:1.
3. Do not exceed the maximum quantity. (The proportion of rice and water could be adjusted according to personal preference)

Yoghurt Program

• Press the ‘Menu’ button and go to the ‘Yoghurt’ program.
• After setup the program, press the “Start” button. The indictor light is on.
• After the cooking process is finished you will hear a beep signal, The Display will show 00 00.

Note: In the ‘Yoghurt’ program the appliance is not going to ‘keep warm’ function after the cooking process is finished, because the yogurt needs low temperature, otherwise the food will have bad smell.

Pasta Program

• Press the ‘Menu’ button and go to the ‘Pasta’ program.
• After setup the program, press the “Start” button. The indictor light is on.

Preparation: Add water to the inner pot, close the lid, and start the program. (Make sure the water is not below the minimum or over the maximum specified level to prevent boiling or damage to the inner pot.) Once the water has boiled, the multicooker will remind you with a beep signal to add the pasta.

The rest of the programs is no special, just choose the program and press the “Start” button to start the cooking process.

CLEANING AND MAINTENANCE

• Unplug the appliance from the power supply and let it cool down before starting any cleaning process!
• Clean the removable parts like the Inner pot, steamer, and aluminum cover with protecting overflow using hot water, cleaning nonabrasive detergent and sponge. Do not use remover, steel wire or any other abrasive utensils.
• If there is stuck food on the bottom of the inner pot, soak for a moment and wipe it up.
• Maintenance of inner pot
• Use plastic or wooden utensils, do not use metal utensils in order to protect the non-stick coating from scratching.
• Do not cut any food in the inner pot.
• Do not put vinegar into the inner pot to avoid corroding.
• Cleaning and maintenance the other parts
• Periodically clean the housing, seal cover and middle ring using a soft, damp cloth. Always dry after cleaning with a dry towel.

ATTENTION!
Never immerse the appliance in water or any other liquid!

TROUBLESHOOTING

Indicators do not light up

| 1. The appliance is not plugged into the power supply

2.  Power cut

| 1. Check for unplugging

2. Check the fuse.

The heating plate does not heat

| 1. Power control plate damaged

2. Fuse damaged

3. Heating plate damaged

| ****

Contact Repair Service Centre

The indicator light is on but the heating plate does not heat| 1. The Heating plate is damaged

2. The power control plate is damaged.

| ****

Contact Repair Service Centre

Rice under-cooker

| ****

1. Capacity of rice is much or less

| The capacity of rice and water should be adjusted and should be limited between the highest and lowest.
2. The proportion of water and rice is not suitable| Adjust the proportion of water and rice
3. Inner pot obliques| Turn the round inner pot, check the sensor of the ‘heating plate’
4. Something between the inner pot and the heating plate| Clean up the sundries
5. Inner pot unshaped| Buy a new one
6. Main Power control plate damaged| Send to ‘Repair Service Centre’
7. Main temperature control machine unusual| Send to Repair Service Centre
Porridge Overflow| The capacity of porridge is excessive

the overflow-proof lid is not installed

| Adjusted the Capacity

Install the overflow–proof lid

LED show: E1, E2, E3, E4

error

| The power control plate had trouble| Send to ‘Repair Service Centre’

RECIPES

French fries

• Preparation – 1 min.
• Cooking – 45 min.
• Total – 55 min.
• potatoes – 500 g
• oil – 100 ml
• cheese – 200 g
• Put 100 ml on the bottom, then peeled, washed and sliced the potatoes. After 10 minutes we stir and after another 10 we take it out and put the next batch. If desired, garnish the french fries with cheese.

Pork with mushrooms and olives

• Preparation – 10 min.

• Cooking – 30 min.

• Total – 40 min.

• pork shoulder – 500 g

• olives – 10 – 15 pcs. black, boned

• mushrooms – 500 g

• butter – 50 g

• pepper

• cumin

• Rosemary
  garlic – 1 – 2 cloves

• Cut the pork into juliennes and, if desired, lightly seal it in a pan with a little oil. Transfer to the multicooker, add the olives, coarsely chopped mushrooms, the rest of the butter and spices. Start a 30 minute baking program.

• Serve the stewed pork in this way or with a garnish of french fries.

Details with beans

• Preparation – 15 min.
• Cooking – 255 min.
• Total – 270 min.
• minced meat – 400 g of veal
• carrots – 1 pc. big
• onion – 1 head
• tomatoes – 200 g of canned cubes
• broth – 400 ml of veal
• oregano – 1 tsp. dry
• basil – 1 tsp. dry
• beans – 400 g red, canned, canned
• details – 1 tsp. pasta
• black pepper – to taste
• oil – 1 tbsp.
• Pour the oil into the multicooker pan and turn on the fryer. Fry the minced meat in the multicooker for 15 minutes. Stir and press with a spoon until it crumbles and changes color for about 10 minutes. Add onions and carrots,
• pre-cut into cubes and fry the remaining 5 minutes. Add diced tomatoes, broth, and spices and start the slow cooker program for 4 hours. After 3 and 1/2 hours, add the beans and pasta and let the dish finish as scheduled.

Chocolate cupcake with nuts

• Preparation – 10 min.
• Cooking – 45 min.
• Total – 55 min.
• eggs – 4 pcs.
• powdered sugar – 225 g
• butter – 75 g
• flour – 160 g
• baking powder – 2 tsp.
• dark chocolate – 100 g
• walnuts – 100 g ground
• In a bowl, break the eggs together with the powdered sugar. Beat until creamy. Add the butter to this mixture and continue beating with the mixer. Gradually add the flour, adding the baking powder in advance. Melt the chocolate in a bowl and pour it, as well as the ground walnuts, to the mixture. Grease the bottom and walls of the cooking vessel with oil or oil and pour the prepared mixture. Choose your program, close the lid and press start.

Sweets

• Preparation – 10 min.
• Cooking – 50 min.
• Total – 60 min.
• FOR CAKE
• flour – 2 2/3 tsp. white
• sugar – 1 1/2 tsp.
• cocoa – 6 tbsp.
• baking soda – 2 tsp.
• salt – 1/2 tsp.
• vinegar – 2 tbsp.
• oil – 2/3 tsp.
• water – 2 tsp.
• vanilla
• ABOUT THE GLAZING
• cocoa
• butter
• sugar
• fresh milk – or water
• Mix the dry ingredients, add the rest and mix with a stirrer until a homogeneous mixture. Place in the baking bowl and bake on the BAKE program for 40 minutes at 150 degrees. Turn and bake on BAKE for 10 minutes at 180 degrees. Remove, cool slightly and cut. Allow to cool. Make a glaze of melted butter, sugar and cocoa and heat in a microwave or water bath until the ingredients are homogenous. The cake is watered, cold, with warm glaze.

Pizza

• Preparation – 10 min.
• Cooking – 30 min.
• Total – 40 min.
• dough – 800 g
• tomato puree – 300 g
• savory
• sol
• melted cheese – 200 g
• mushrooms – 300 g
• salami – 200 g
• yellow cheese – 300 g
• We take a ball of dough and put it on the bottom of the multicooker, trying to lay it on the bottom of the bowl of the appliance.
• On the dough put the products (tomato paste, salt, savory, mushrooms, melted cheese, salami and cheese) in the desired amount. As for ordinary pizza and we turn on the appliance. Bake on the Bake program at 180 degrees for 25-30 minutes.

Cream chicken with mushrooms and leeks

• Preparation – 10 min.
• Cooking – 55 min.
• Total – 65 min.
• leeks – 1 stalk
• chicken legs – 1 kg.
• red pepper – 1 tbsp.
• nutmeg
• white pepper
• sol
• mushrooms – 300g.
• cream – 300 ml. cooking
• oil – 3 tbsp.
• Clean the leek and cut it into pieces. Put it together with the oil and red pepper in the bowl of the multicooker. Turn on and set the program to 55 minutes. Cook for 6-7 minutes until the leeks are soft. Add the chicken legs and the sliced and cleaned mushrooms. Season with salt, white pepper and nutmeg. Cook for about 15 minutes, then pour the cream, close the lid and allow the dish to cook and thicken. Serve the dish with finely chopped parsley.

Delicious bread

• Preparation – 10 min.
• Cooking – 100 min.
• Total – 110 min.
• flour – 250 g white
• standard flour – 150 g
• rye flour – 100 g
• salt – 1 1/2 tsp.
• sugar – 1 tbsp.
• olive oil – 1 tbsp.
• yeast – 1 sachet dry
• water – 320 ml lukewarm
• oil – for spreading
• Sift the flour into a bowl. Add the remaining products and stir. Add a little water and knead a soft dough. Form the finished dough into a ball. Grease the bowl of the multicooker with oil with a silicone brush. Put the ball of dough
• in the middle and set the BAKE program, setting the temperature to 60 degrees and the rising time to 45 minutes. Press the START button. Once the dough has risen and doubled in volume, switch off the mode from the MENU,
• and program again with the BAKE button, but this time at 150 degrees for 55 minutes. 10 minutes before the end of baking, open the lid and carefully turn the bread to bake evenly. After baking, turn the bread on the grill. The bread is very tasty, soft inside and with a crispy crust.

Bread pie with potatoes and bacon

• Preparation – 30 min.
• Cooking – 55 min.
• Total – 85 min.
• FOR THE DOUGH
• flour – 300 g
• May – 1 tsp. dry
• salt – 1 tsp.
• sugar – 1 tsp.
• fresh milk – 1 tsp.
• oil – 2 tbsp.
• FOR THE STUFFING
• potatoes – 3 pcs. cooked medium-sized
• leeks – 1 stalk
• eggs – 1 pc.
• bacon – 50 g
• sol
• pepper
• oil – 3 tbsp.
• yellow cheese – for sprinkling
• paprika – for sprinkling
• Dissolve the yeast in the milk. Add the sugar and stir. Add the liquid and other ingredients to the flour and knead a soft dough. Let it double in volume. Peel a leek and cut it into circles. Stew it in the fat. Add the chopped bacon and fry for 2-3 minutes. Remove the filling from the hob and cool. Mash the potatoes, season with salt and pepper and beat the egg. Stir until homogeneous. Spread the dough on a thin crust. Put a layer of potatoes, and on top – a
• layer of stuffing with leeks and bacon.
• Gather the edges of the dough and form into a ball. Grease the bowl of the multicooker with fat, put the bread ball and turn on the baking program – 55 minutes. 10 minutes before the end of baking turn the bread pie. Remove the finished pie and while still warm, sprinkle with grated yellow cheese and paprika.

Pasta Bolognese

• Preparation – 10 min.
• Cooking – 45 min.
• Total – 55 min.
• olive oil – 1 – 2 tbsp.
• onion – 1 medium head
• of carrots – 1 pc.
• celery – dry or fresh
• mushrooms – 5 – 6 pcs ..
• minced meat – 250 g.
• tomato puree – 2 tbsp.
• tomatoes – 4 – 5 pcs.
• garlic – 1 clove
• universal spice – 2 tsp. spaghetti spice
• foam – 250 g
• water – 270 ml
• red wine – 50 ml
• Finely chop the vegetables. Put olive oil, onions, carrots, celery, mushrooms and minced meat in the cooking vessel. Press the MENU button, and select the FRY program. Press TIME and set to 13 minutes. Press START.
• Fry for 8 minutes, then add the tomato puree, chopped tomatoes, garlic, spices and red wine. Continue with FRY. Add the paste and water at the same time. Select the STEW program and set the time to 30 minutes. Close the lid and press START. Serve the finished pasta with grated Parmesan or another type of cheese if desired.

Spaghetti Carbonara

• Preparation – 5 min.
• Cooking – 37 min.
• Total – 42 min.
• olive oil – 1 tbsp.
• onion – 1/2 medium-sized head
• garlic – 1 clove
• spaghetti – 200 g
• bacon – 100 g
• cooking cream – 180 ml
• water – 540 ml
• yolks – 3 pcs.
• parmesan – 4 tbsp. grated (or yellow cheese)
• sol
• pepper
• Put olive oil, finely chopped onion and crushed garlic in the cooking vessel. Press the MENU button and select the FRY program.
• Press the TIME option, set 10 minutes. Start with START. Stir occasionally. Break the spaghetti in half and add them to the bowl along with the water. Set 20 minutes and press the STEW and START buttons. Close the lid. After the time has elapsed, add the yolks mixed with the cream. Set for another 7 minutes. When cooking is finished, it automatically switches to KEEP WARM mode. Sprinkle the prepared spaghetti with parmesan or yellow cheese.

Stew with potatoes

• Preparation – 25 min.
• Cooking – 70 min.
• Total – 95 min.
• potatoes – 10 pcs.
• tomato puree – 1 tbsp.
• carrots – 2 – 3 pcs.
• olive oil – 3 tbsp.
• leeks – 1 stalk
• onion – 1 head
• garlic – 2 cloves
• rice – ¼ tsp.
• red pepper – 1 tbsp.
• flour – 1 tbsp.
• broth – hot vegetables (maybe water)
• pepper
• parsley
• sol
• Wash and clean the vegetables. Pour the fat into the multicooker, add the chopped onion and garlic. Select the frying function and set the time to 10 minutes. Stir occasionally, and at the 5th minute add the chopped leeks and carrots. At the end, add the potatoes. Mix the flour with the red pepper and add to the vegetables. Pour hot vegetable broth to cover the level of vegetables.
• Season with black pepper and salt, close the lid and press the cooking button for 1 hour. After about half an hour add the rice, and in the last minutes add the parsley and puree.

Stuffed peppers

• Preparation – 25 min.
• Cooking – 65 min.
• Total – 90 min.
• peppers – 8 – 10 pcs.
• minced meat – 250 g of the mixture
• rice – 1 tsp.
• olive oil – 1 tbsp.
• tomato puree – 2 tbsp.
• carrots – 1 – 2 pcs.
• onion – 1 head
• pepper
• flour
• rice – 3/4 tsp.
• sol
• Clean the peppers and remove the seeds. Put olive oil, chopped carrots, rice and onions in the multicooker. Select the frying function and program for 15 minutes, start and stir periodically while the vegetables are cooking. After about 5 minutes, add the meat and season with salt. Add the water. When the liquid boils, you need to open the lid and allow the mixture to cool. Fill the peppers with rice and add a little flour. Arrange the peppers in the pan and add enough water to cover the peppers in half.
• Select the cooking function for 40 minutes and start.

Risotto with vegetables

• Preparation – 25 min.
• Cooking – 65 min.
• Total – 90 min.
• rice – 300 g long grain
• peppers – 1 small red + 1 small green
• olive oil – 1 tbsp.
• onion – ½ small head
• of mushrooms – 50 g
• peas – 60 g frozen
• tomatoes – 150 g chopped
• broth – 350 ml of vegetable
• saffron – 1 pinch
• Pour olive oil into the multicooker. Select the frying program and set for 10 minutes. Pour the chopped peppers, tomatoes, mushrooms and onions. Stir occasionally to avoid burning. Add the rice, and after a while the broth, peas and saffron. Season the risotto with salt and spices of your choice. Choose the rice program and get started.

The symbol means that the product should not be disposed of with household waste in order to avoid environmental contamination and human injury. Take the appliance to a specialist recycling center for electrical appliances.

MANUFACTURER AND IMPORTER

• Keten LTD.; VAT: BG123670208; fl. 7, 39 Vladimir Vazov blvd., 1836, Sofia, Bulgaria
• Phone: +359 2 8691023; Fax: +359 2 8691025; e-mail: sales@keten.bg; www.keten.bg.

References

• Homepage | Keten

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>