reolink RLC-810A 4K 8MP Telecamera Esterno Bullet Instruction Manual
- June 12, 2024
- reolink
Table of Contents
reolink RLC-810A 4K 8MP Telecamera Esterno Bullet Instruction Manual
What’s in the Box
Camera
Waterproof Lid
Ethernet Cable
Quick Start Guide
Surveillance Sign
Mounting Hole Template
Pack of Screws
Camera and accessories vary with different camera models that you purchase.
Camera Introduction
Press for about 10 seconds to restore the device to factory settings.
Press for about 10 seconds to restore the device to factory settings.
- Different types of cameras are introduced in this section. Please check out the camera included in the package and check out the details from the corresponding introduction above.
- The actual appearance and components may vary with different model of product.
Connection Diagram
- Different types of cameras are introduced in this section. Please check out the camera included in the package and check out the details from the correpsonding introduction above.
- The actual appearance and components may vary with different model of product.
- Before using the camera, please connect your camera as instructed below to finish initial setup.
- Connect the camera to a Reolink NVR (not included) with an Ethernet cable.
- Connect the NVR to your router, and then power on the NVR.
Set up the Camera
Download and launch the Reolink App or Client software, and follow the onscreen instructions to finish initial setup.
If you are connecting the camera to a Reolink PoE NVR, please set up the camera via the NVR interface.
Mount the Camera
Installation Tips
- Do not face the camera towards any light sources.
- Do not point the camera towards a glass window. Or, it may result in poor image quality because of the window glare by infrared LEDs, ambient lights or status lights.
- Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image quality. To ensure best image quality, the lighting condition for both the camera and the capture object shall be the same.
- To ensure better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
- Make sure the power ports are not directly exposed to water or moisture and not blocked by dirt or other elements.
- With IP waterproof ratings, the camera can work properly under conditions like rain and snow. However, it doesn’t mean the camera can work underwater.
- Do not install the camera at places where rain and snow can hit the lens directly.
- The camera may work in extreme cold conditions as low as -25°C. Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it outdoors
There are two different types of mounts for bullet cameras. Please check out the mount included in the package and follow the corresponding instruction to install the camera properly.
Install the Camera
Drill holes in accordance with the mounting hole template
Use the drywall anchors included in the package if needed.
Install the mount base with the mounting screws included in the package
Run the cable through the cable notch on the mount base.
To get the best field of view, loosen the adjustment knob on security mount
and turn the camera.
Stiffen the adjustment knob to lock the camera.
If your camera has another mount without the adjusting knob, please loosen the
adjusting screw with the provided hex key and turn the camera as shown below
to adjust the angle.
Troubleshooting
Camera is not Powering On
If your camera is not powering on, please try the following solutions:
- Make sure your camera is powered properly. The PoE camera should be powered by a PoE switch/injector, the Reolink NVR or a 12V power adapter.
- If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see if the camera will power on.
- Try again with another Ethernet cable.
Infrared LEDs Stop Working
If the Infrared LEDs of your camera stop working, please try the following solutions:
- Enable infrared lights on Device Settings page via Reolink App/Client.
- Check if the Day/Night mode is enabled and set up auto infrared lights at night on Live View page via Reolink App/Client.
- Upgrade the firmware of your camera to the latest version.
- Restore the camera to factory settings and check out the infrared light settings again.
Failed to Upgrade the Firmware
If you fail to upgrade the firmware for the camera, try the following solutions:
- Check out the current camera firmware and see if it is the latest one.
- Make sure that you download the correct firmware from Download Center.
- Make sure that your PC is working on a stable network.
Specifications
Hardware Features
Night Vision: 30 Meters (100ft) Day/Night Mode: Auto Switchover
General
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Operating Humidity: 10%-90%
In ress Protection: IP66
Notification of Compliance
FCC Compliance Statement
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Simplified EU Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes. throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
REOLINK INNOVATION LIMITED FLAT/RM 705 7/F FA YUEN COMMERCIAL BUILDING 75-77
FA YUEN STREET MONG KOK KL HONG KONG
EUI REPI Product !dent GmbH
Hoferstasse: 9B, 71636 Ludwigsburg, Germany
prodsg@libelleconsulting.com
IUKI REPI
APEX CE SPECIALISTS LIMITED: 89 Princess Street, Manchester, M1 4HT, UK
info@apex-ce.com
Aug: 2021 QSG1_B 5 8.0 3.00 5.0013
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>