HYENA E-BIKE CE-02 LED Chip Instruction Manual

June 12, 2024
HYENA E-BIKE

HYENA logo Product Manual
LED Chip (CE-02) Original Instruction

Introduction

This manual is intended primarily for the trained technician to install, disassemble, or maintain the Hyena e-bike system only.
Please read all the safety warnings and instructions carefully. Failure to follow the warnings and instructions may result in death or severe injuries. Save this manual for future reference.

Product Features

Product Description
The Hyena LED Chip (CE-02) e-bike frame embedded HMI features compact size, single button, and multi-color LED indicators, designed to mount into the bike frame to keep the bike’s elegant outlook. It also supports the rider’s app and the service tool connection via Bluetooth.
Parts DescriptionHYENA E BIKE CE-02 LED Chip - Parts
Description

Item Description Item Description
A Fastening screw D Power & support level button
B Battery capacity & support level indicator (Blue/ Red color) E Cable
C Function indicator (White/ Blue/ Red color)

Product Dimension

HYENA E BIKE CE-02 LED Chip - Product Dimensionhttps://www.hyena-ebike.com/

Cable Pin Definition

Technical Data

Function

Number of buttons| 1|
---|---|---
Turn on/off system| Main button| On: short press/Off: long press
Switch motor support level| Main button| Short press
Turn on/off light| N/A|
Walk-assist| N/A|
Connection| Bluetooth/Hyena 6P| CM-WP408-06M
Battery wake up function| Yes| HMI/DEN

Characteristic

Protocol CAN Support Hyena CAN
Rated voltage 12Vdc The equipment must apply power output with < 100W DC

power equipment.
Operating voltage| 10 to 14Vdc|
Rated current| 0.1A|
Quiescent current| <1mA| Measure condition
a. System off
b. Battery, HMI, Display, Controller, Motor and Sensor are connected well.
c. Remove all smart parts.
Operating temperature| -10℃ to +50℃ 80%RH|
Storage temperature| -20℃ to +70℃ 80%RH|
Waterproof level| IPX5|

Mounting Parameter

Dimension (mm)| L67.7, W28.8, H18.0 mm|
---|---|---
Weight| 21g|
Mounting position| Bike frame|
Cable length| 55±5 mm|
Standard connector| Hyena 6P male| CM-WP408-06M

Connection

Bluetooth connection| Bluetooth 4.2| Support to HRA (Hyena Rider Assistant ) & HST (Hyena Service Tool)
---|---|---

LED Indicator Information

Motor support level 0 to 3
Battery status 3 segments

Certification

EN 15194:2017| Yes|
---|---|---
CE| Yes|
BQB| Yes| Bluetooth
RoHS 2.0| Yes|

Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

  1. This device may not cause interference; and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

Mounting

Tool List
Hexagon key M3

Accessory List

Hex socket head cap screw M3x0.5Px6mm 1 pc

Mounting Instructions

  • Use the proper tools during the installation or removal process.
  • Fasten the hex bolt with 1 Nm torque value.
  • Carefully install is necessary, do not strike it with any tool such as a hammer or wrenches.

HYENA E BIKE CE-02 LED Chip - Mounting Instructions NOTE: The bike image and mounting position seen in the manual may be different from the actual bike, but it will be enough to help you understand related instructions.
E-System Operation
CAUTION! The e-bike system can only be activated when the following requirements are met:

  • A sufficiently charged battery is attached.
  • The e-system is connected properly.

Operation Instructions
Turn on/off the e-bike system
Short press the POWER button to turn on, and long press the POWER button to turn off. HYENA E BIKE CE-02 LED Chip - e-bike systemWhen system is on, the indicator shows the battery status.
NOTE
Always switch off the e-bike system when parking the e-bike or before removing the battery.
Battery indicator
The indicator shows the battery status. HYENA E BIKE CE-02 LED Chip -
Battery indicatorSupport level adjusting
Short press the POWER button to switch to support level adjusting mode. The indicator will change to red light, then short press to adjust the riding support level.

  • Default on Off mode.
  • Automatic memory previous setting.

HYENA E BIKE CE-02 LED Chip - Support level adjustingUnder the support level adjusting mode, release the button for 3 seconds (no operation), and the indicator turns back to battery status.
NOTE

  • The system is activated as soon as you start pedaling.
  • The e-bike drive output only supports a speed below 25/32 km/h, as soon as you have reached 25/32 km/h, e-system switches off the assistance, then automatically reactivates when your speed is below 25/32 km/h.

HYENA E BIKE CE-02 LED Chip - Charging indicatorIndicator flashing ends when battery full charged.

Error alert
The bottom light flashes red when a system error is detected. HYENA E BIKE
CE-02 LED Chip - Error alertBluetooth connection
Blue lights flash 3 times when Bluetooth connects. When connected, the bottom indicator shows blue; when connecting failed or disconnected, the bottom indicator shows white. HYENA E BIKE CE-02 LED Chip - Bluetooth
connectionService tool connection
When maintaining or diagnosing your e-bike via Hyena Service Tool (HST), follow the software instruction and double click the power button in 0.5 seconds, to connect your e-bike to the computer. E-bike system update
When updating the e-bike system firmware, the bottom indicator keeps flashing white. When updating is completed, the system reboots itself.

Safety Instructions

Instructions Pertaining To A Risk Of Fire, Electric Shock, Or Injury To Persons
WARNING! When using the LED Chip (CE-02) HMI, basic precautions should always be followed, including the following:

  • Read all the instructions before using the product.
  • Close supervision is necessary to reduce the risk of injury when using the product near children.
  • Do NOT put fingers or hands into the product.
  • Do NOT use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage.
  • All the component leads shall use original Hyena components.
  • This product is not intended to be used at ambient temperatures above 50°C(122°F) or less at ambient temperatures of -10°C(14°F).
  • Do NOT immerse the product or any e-system component in water.
  • Do NOT place the product or any e-system component near fire or heat.
  • Always turn off the e-bike system and remove the battery before installing, disassembling, or modifying any components on the e-bike.

Important Notice

  • This product manual is intended primarily for the trained technician to install, disassemble or maintain the e-bike.
  • Users not professionally trained for bicycle assembly should not attempt to install, disassemble or modify the components themselves.
  • All Hyena e-system manuals and technical documents are accessible online at “www.hyena-ebike.com”.
  • The term “battery” is used in these instructions to mean all original Hyena e-bike batteries.
  • Read and observe the safety warnings and directions contained in all the Hyena e-bike system operating instructions and in the operating instructions of your ebike.

Moving and Storage Instructions

  • Please keep the product and all e-system components in their original package and keep tools or other metal objects away from them during storage and moving.
  • If you did not keep the original packaging, they can be packed in strong cartons with proper packing materials such as bubble wrap or soft cloth, and label the cartons “Fragile”.
  • Do NOT store the product at ambient temperatures above 70°C (158°F) or less at ambient temperatures of -20°C (4°F).
  • Cover the product to prevent sunlight damage if you keep it stored at any place for more than a week.
  • Store the product on a fireproof surface without contact with water, heat, or sand.
  • Do NOT place any heavy item on the product or any esystem component.
  • Do NOT place the product or any e-system component in the car trunk for over a day.
  • Do NOT load or move the product in the rain whenever possible, and make sure it has no moisture or mildew before loading it.
  • Do NOT drop the product from more than 30 cm (11.81 inches) in height.

Maintenance

  • Do NOT clean the product or any e-system component with detergent or organic solvent. Only clean the product with a water-dampened soft cloth.
  • Do NOT clean the product or any e-system component with pressured water.

Product Label

  • You can find the model name and related information at the bottom of the product.

HYENA E BIKE CE-02 LED Chip - Product Labelhttps://www.hyena-ebike.com/

Disposal

  • In accordance with Directive 2012/19/EU, electronic devices that are no longer usable and defective/ drained batteries must be collected separately and recycled in an environmentally friendly manner.
    **** This symbol is only valid within the European Union. Follow local regulations when disposing of used batteries. If you are not sure, consult the place of purchase or a bicycle dealer.

  • The e-system drive unit, including the motor, controller, battery, speed sensor, torque sensor, HMI, accessories, and packaging, should be disposed of in an environmentally correct manner.

  • Do NOT dispose of e-bikes and their components with household waste.

SAVE THESE INSTRUCTIONS

Hyena Inc.
Tel: +886 4 23598810
Fax: +886 4 23598610
www.hyena-ebike.com
Address: No.25, Jingke N. Rd., Nantun Dist., Taichung City 408, Taiwan (R.O.C.)
Version 230522
Copyright © 2023 HYENA INC. All Right Reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals