Hyena E-Bike Systems CC-02 LCD Compact EX Owner’s Manual

June 13, 2024
Hyena E-Bike Systems

Hyena E-Bike Systems CC-02 LCD Compact EX Owner’s Manual
Hyena E-Bike Systems CC-02 LCD Compact EX

Introduction

This manual is intended primarily for the trained technician to install, disassemble, or maintain the Hyena e-bike system only. Please read all the safety warnings and instructions carefully. Failure to follow the warnings and instructions may result in death or severe injuries. Save this manual for future reference.

Product Features

Product Description

The Hyena LCD Compact EX (CC-02) e-bike handlebar HMI features all in one function: compact size with complete info and precise digital information, large ergonomic buttons. In addition, support the Apps and service tool connection via Bluetooth.

Parts Description

Parts Description

Item Description
A Display screen
B UP & Increase support level button
C DOWN & Decrease support level button
D Fastening screw
E Power on/off button
F USB connection port (for diagnostic)
G Cable
H Walk-assist button

DISPLAY ELEMENT

Item Description
a Light indicator
b Speed/range
c Display information type
d Battery capacity indicator
e Error indicator
f Bluetooth indicator
g Unit indicator
h Support level

Product Dimension

Item Dimension (mm)
A 45.7
B 47.7
C 570 or 720
D 29.5
E Φ4.0
F 49.0
G Φ22.2

Product Dimension
Product Dimension

Cable Pin Definition

Cable Pin Definition

Technical Data

Function

Number of button 4 Power/Up/Down/Walk
Turn on/off system Power button
Switch motor support level Up/Down button
Switch information Short press walk-assist button Current speed &

Range
Turn on/off light| Long press Up button|
Walk-assist| Refer to page 7|
USB charging| Max. 5V/1A| USB 2.0 TYPE A
Connection| Bluetooth / USB 3.0 / Hyena 6P|
Battery wake up function| Yes| HMI/DEN

Characteristic

Protocol CAN Support Hyena CAN
Rated voltage 12Vdc
Operating voltage 10 to 14Vdc
Rated current 0.6A
Quiescent current <1mA Measure conditiona.  System offb. Battery, HMI,

Display, Controller, Motor and Sensor are connected well.c. Remove all smart parts.
Operating temperature| -10℃ to +40℃ @80%RH|
Storage temperature| -20℃ to +70℃ @80%RH|
Waterproof level| IPX5|

Mounting Parameter

Dimension (mm)| L47.7, W45.7, H48.9 mm|
---|---|---
Mounting position| Left handle bar|
Clamp diameter| 22.2 mm|
Cable length| 570/ 720 mm| 40010C20A: 570mm40010C22F: 720mm
Standard connector| Hyena 6P male| CM-WP408-06M
Compatible of brake| BL-T4000 / BL-M6000 BL-MT201 / BL-MT401| ** SHIMANO
Compatible of shifter**| Do not recommend|

Connection

Connection Bluetooth connection| Bluetooth 4.2 BLE| Support to HRA (Hyena Rider Assistant) rider app & HST (Hyena Service Tool)
---|---|---
USB connection| USB 3.0 TYPE A| Support to HST

Indicator Information

Current speed 0 to 99 Unit in 1 km/hour
Range 0 to 99 Unit in 1 km (Battery with Hyena CAN required)
Riding support level 0 to 4
Battery status 5 segments
Light on indicator Head light icon
Bluetooth status Bluetooth icon
Error alert Warning icon & Number Refer to error code table

Certification

EN 15194:2017| Yes|
---|---|---
CE| Yes|
BQB| Yes| Bluetooth
RoHS 2.0| Yes|

Mounting

Tool List

  • Hexagon key M3: Disc hex bolts

Accessory List

  • Hex socket head screw: M3x0.5Px10mm 1 pc

Mounting Instructions

  • Use the proper tools during the installation or removal process.
  • Fasten the hex bolt with 1.0 Nm torque value.
  • Carefully install is necessary, do not strike it with any tool such as a hammer or wrenches.

Mounting Instructions 

Mount the HMI hook on the handlebar.
Mounting Instructions 

Mount and fasten the hex socket head screw with torque to 0.25 Nm (2.5 kgf/cm).

Operation
Caution! The e-bike system can only be activated when the following requirements are met:

  • A sufficiently charged battery is attached.
  • The e-system is appropriately connected.

Operation Instructions

Turn on/off the e-bike system
Long press the power button to turn it on/off
Operation Instructions

Switch between speed mode/range mode
Short press the power button to switch information.
Operation Instructions

NOTE
Always switch off the e-Bike system when parking the e-Bike or before removing the battery.

Support level adjusting
Short press the UP/ DOWN button to adjust the support level while you pedal.

  • Default on Off mode
  • None circulation

Operation Instructions

NOTE

  • The system is activated as soon as you start pedaling.
  • The e-bike drive output only supports a speed below 25/45 km/h, as soon as you have reached 25/45 km/h, the e-system suspends the motor support, then automatically reactivates when your speed is below 25/45 km/h.

Turn on/off light
Long press UP button to turn on/off light when e-bike equipped with front/rear lights.
Turn on/off light

Walk assistance
Long press and hold the WALK assist button to activate the walk assist mode.
Walk Assistance

Press and hold the UP button to start the walk assist. As long as you are holding the up button, your e-bike will be propelled forward at a slow speed.
Walk Assistance

Release the UP button to stop pushing your e-bike. Suppose no buttons are pressed within 5 seconds in the walk assist mode. In that case, system will return to general mode automatically for safety. Or if the DOWN/ WALK assist button is pressed in the walk assist mode, the system will also return to the general mode.

NOTE
The walk assistance function must only be used when pushing the e-bike. Make sure you are ready and stand steady before activating the walk assistance.

Do NOT activate the walk assistance when you ride on the e-bike or if the wheels are not in contact with the ground.

Bluetooth connection
Bluetooth indicator shows when connected.
Bluetooth Connection

Battery indicator
The icon shows the battery capacity
Battery Indicator

Error alert
The error code shows on the middle screen when a system error is detected. Refer to the error code list for details.
Error Alert

The alert icon stays on display when the number indicator returns to the general riding info. All the HMI function remains the same.

Suspend the error alert
Press any button to suspend the error code flashing; the alert icon will stay on until the system error is solved.

Error Code List

Code| Category| Error Description| Code| Category| Error Description
---|---|---|---|---|---
16| Torque sensor| Torque sensor voltage too high| 68| Battery| Charging temperature error
17| Torque sensor| Torque sensor voltage too low| 69| Battery| Battery cell overvoltage
20| Front TPMS| Front tire pressure too high| 70| Battery| Battery cell undervoltage
21| Front TPMS| Front tire pressure too high| 71| Battery| Battery overcharge
22| Front TPMS| Front TPMS battery capacity low| 72| Battery| Battery short circuit
23| Front TPMS| Front TPMS temperature too high| 73| Battery| Battery overdischarge
24| IoT Box| Satellite positioning error| 74| Battery| Discharging temperature error
25| IoT Box| SIM card error| 75| Battery| Battery cell balancing error
26| IoT Box| Database error| 80| Controller| Controller overheat
27| IoT Box| Fail to connect server| 81| Controller| Battery communication error
32| Motor| Motor hall all voltage too high| 82| Controller| Locked rotor (pedal assist)
33| Motor| Motor hall all voltage too low| 83| Controller| Locked rotor (walk assist)
34| Motor| Motor signal error (U)| 84| Controller| Controller communication error
35| Motor| Motor signal error (V)| 85| Controller| Controller FET error (U)
36| Motor| Motor signal error (W)| 86| Controller| Controller FET error (U)
37| Motor| Motor malfunction (U)| 87| Controller| Controller FET error (V)
38| Motor| Motor malfunction (V)| 88| Controller| Controller FET error (V)
39| Motor| Motor malfunction (W)| 89| Controller| Controller FET error (W)
40| Motor| Motor overheat| 90| Controller| Controller FET error (W)
44| Rear TPMS| Rear tire pressure too high| 91| Controller| Controller FET circuit error
45| Rear TPMS| Rear tire pressure too low| 92| Controller| Controller FET overcurrent (FW)
46| Rear TPMS| Rear TPMS battery capacity low| 93| Controller| Controller FET overcurrent (HW)
47| Rear TPMS| Rear TPMS temperature too high| 94| Controller| Controller protection unit error
48| Speed sensor| Speed sensor error| 95| Throttle| Locked rotor (Throttle)
49| Speed sensor| Cadence sensor error| 96| Throttle| Throttle overvoltage
50| Chain| Drivetrain error| 97| Throttle| Throttle undervoltage
55| Rear brake light| Brake light malfunction| 98| HMI| Button communication fail
56| Horn| Horn malfunction| 99| HMI| HMI button communication error
59| Turn Lights| Turn signal error (RR)| 100| HMI| Display panel malfunction
60| Turn Lights| Turn signal error (RL)| 101| HMI| USB charge port error
61| Turn Lights| Turn signal error (FR)| 112| Front light| Front light malfunction
62| Turn Lights| Turn signal error (FL)| 113| Maintenance| Maintenance notification
64| Battery| Battery overvoltage| 114| Bluetooth| Bluetooth error
65| Battery| Battery undervoltage| 115| Brake sensor| Brake sensor error
66| Battery| Low capacity| 116| Rear light| Rear light malfunction
67| Battery| Empty capacity| 117| Light| Light short circuit

Safety Instructions

Instructions Pertaining To A Risk Of Fire,
Electric Shock, Or Injury To Persons

WARNING! When using the LCD Compact EX (CC-02) e-bike HMI, basic precautions should always be followed, including the following:

  • Read all the instructions before using the product.
  • Close supervision is necessary to reduce the risk of injury when using the product near children.
  • Do NOT put fingers or hands into the product.
  • Do NOT use this product if the flexible power cord or output cable is frayed, has broken insulation, or any other signs of damage.
  • All the component leads shall use original Hyena components.
  • This product is not intended to be used at ambient temperatures above 40°C(104°F) or less at ambient temperatures of -10°C (14°F).
  • Do NOT immerse the product or any e-system component in water.
  • Do NOT place the product or any e-system component near fire or heat.
  • Always turn off the e-bike system and remove the battery before installing, disassembling, or modifying any components on the e-bike.
  • The connection length between this HMI to its power supply (controller), including extension cables, shall be limited to under 3 meters.

Important Notice

  • This product manual is intended primarily for the trained technician to install, disassemble or maintain the e-bike.
  • Users not professionally trained for bicycle assembly should not attempt to install, disassemble or modify the components themselves.
  • All Hyena e-system manuals and technical documents are accessible online at “www.hyena-ebike.com”.
  • The term “battery” is used in these instructions to mean all original Hyena e-bike batteries.
  • Read and observe the safety warnings and directions contained in all the Hyena e-bike system operating instructions and in the operating instructions of your e-bike.

Moving and Storage Instructions

  • Please keep the product and all e-system components in their original package and keep tools or other metal objects away from them during storage and moving.
  • If you did not keep the original packaging, they can be packed in strong cartons with proper packing materials such as bubble wrap or soft cloth, and label the cartons “Fragile”.
  • Do NOT store the product at ambient temperatures above 70°C (158°F) or less at ambient temperatures of -20°C (-4°F).
  • Cover the product to prevent sunlight damage if you keep it stored at any place for more than a week.
  • Store the product on a fireproof surface without contact with water, heat, or sand.
  • Do NOT place any heavy item on the product or any e-system component.
  • Do NOT place the product or any e-system component in the car trunk for more than one day.
  • Do NOT load or move the product in the rain whenever possible, and make sure it has no moisture or mildew before loading it.
  • Do NOT drop the product from more than 30 cm (11.81 inches) in height.

Maintenance

  • Do NOT clean the product or any e-system component with detergent or organic solvent. Only clean the product with a water-dampened soft cloth.
  • Do NOT clean the product or any e-system component with pressured water

Product Label

On the product label at the bottom of the HMI, you can find the product number and QR code.

Disposal

In accordance with Directive 2012/19/EU, electronic devices that are no longer usable and defective/ drained batteries must be collected separately and recycled in an environmentally friendly manner.

This symbol is only valid within the European Union. Follow local regulations when disposing of used batteries. If you are not sure, consult the place of purchase or a bicycle dealer

  • The e-system drive unit, including the motor, controller, battery, speed sensor, torque sensor, HMI, accessories, and packaging, should be disposed of in an environmentally correct manner.
  • Do NOT dispose of e-bikes and their components with household waste.

SAVE THESE INSTRUCTIONS

Hyena Inc.
Tel : +886 4 23598810
Fax: +886 4 23598610
www.hyena-ebike.com
Address: No.25, Jingke N. Rd., Nantun Dist., Taichung City 408, Taiwan (R.O.C.)

Hyena Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals