anko 43020614 Pet Gate with Extension Instruction Manual

anko 43020614 Pet Gate with Extension

Product Information

The Pet Gate With Extension is a versatile gate designed to keep your pets safe and secure in designated areas of your home. It features a pressure- mounted installation, making it easy to install and remove without the need for drilling or permanent fixtures. The gate is adjustable and can fit various doorways and openings, providing flexibility for different spaces.

Assembly Instructions

1. Take out the cap screw (No.2) and plastic nut (No.3). Screw them together by following the image provided in the manual. Pay attention to the direction of the plastic nuts.
2. Without the extension, insert the upper plastic cap (No.6) into the upper side holes of the safety gate (No.1) on both sides. Insert the lower plastic cap (No.7) into the lower side holes on both sides. Then insert the four accessories assembled in Step 1 into the upper and lower caps (No.6 and No.7) holes of the gate.
3. Put the pet gate (No.1) on the ground and ensure it is vertical and flat on the floor. Mark the four corner positions and distances of the door according to the image provided. Remove the gate, thread the self-tapping screw (No.5) through the wall cup (No.4), and attach it to the wall at the marked positions using a screwdriver. Repeat this step for the other three marked positions. Place the flat side of the wall cup (No.4) against the wall.
4. Put the gate into the right side of the wall cups first. Adjust the distance between plastic nuts (No.3) and cap screws (No.2) on the four corners to ensure you can put the left side gate in. Keep the gate switch horizontal. Then tighten the plastic nuts (No.3) at the four corners using a spanner (No.8) to securely connect the gate switch part to the left frame.
5. Using the extension option, the gate base can be equipped with an extension tube (No.11) on either side. Refer to the provided image for guidance. Insert the upper extension plastic cap (No.9) and lower extension plastic cap (No.10) into the safety gate (No.1) and extension tube (No.11) as shown in the image. Then follow step 2 above to attach accessories (No.2, 3, 6, and 7) to the extension tube (No.11).
6. To open the pet gate, push the button and lift the back side of the handle. This will allow you to open the gate. To close the pet gate, press down on the handle until you hear a clicking sound.
7. To uninstall, twist the four plastic nuts (No.3) in a reverse way to loosen the four corners of the pet gate. This will allow you to remove it from its pressure-mounted position.

Contents

PARTS

Assembly Instructions

• Step 1.
  Take out the cap screw (No.2) and plastic nut (No.3), and screw them together by following below right image. Please pay attention to the direction of plastic nuts at this step.

• Step 2 Without an extension
  Insert the upper plastic cap (No. 6) into the upper side holes of the safety gate (No.1) on both sides. Insert the lower plastic cap (No.7) into lower side holes on both sides. Then insert the four accessories assembled in Step 1 into the upper and lower caps (No. 6 and No. 7) holes of the gate.

• Step 3.
  Put the pet gate (No.1) on the ground and make sure the gate is vertical and flat on the floor. Mark the four corner positions and distances of the door according to the below middle picture. Then remove the gate, thread the self- tapping screw (No. 5) through the wall cup (No.4), and attach it to the wall (marked position) with a screwdriver. Repeat it at the other three marked positions. Please place the flat side of the wall cups (No.4) against the wall.

• Step 4.
  Put the gate into the right side of the wall cups first. Adjust the distance between plastic nuts (No. 3) and cap screws (No.2) on the four corners to make sure you can put the left side gate in. Keep the gate switch horizontal. Then tighten the plastic nuts (No.3) at four corners by using a spanner (No.8), make sure to tightly connect the gate switch part to the left frame.

• Step 5 Use the extension option
  The gate base can be equipped with an extension tube (No.11) on either side. Please refer to the below image. Use the upper extension plastic cap (No. 9) and lower extension plastic cap (No. 10) inserted into the safety gate (No.1) and extension tube (No. 11) as the image below. Then follow step 2 above to attach (No. 2, 3, 6, and 7) to extension tube (No. 11)

• Step 6.
  Open the pet gate: push the button①, lift the back side of the handle②, open the gate③;
  Close the pet gate: press down the handle until you hear a “click” sound.

• Step 7.
  Un-Installation: Twist the four plastic nuts (No.3) in a reverse way, and loosen the four corners of the pet gate to remove it from the pressure-mounted position.

WARNING: THIS GATE IS FOR PET USE ONLY.
WARNING: THIS GATE MUST NOT BE FITTED ACROSS OR BETWEEN WINDOWS. THIS GATE MUST BE FITTED BETWEEN RIGID SURFACES SUCH AS DOORWAYS OR WALLS,

• ALONG WITH MOUNTING CUPS SECURED WITH SCREWS.
• NEVER USE WITHOUT MOUNTING CUPS.
• TO MAKE YOUR PET SAFE, INSTALL THE GATE SECURELY AND INSPECT THE COMPONENTS
• ARE TIGHT REGULARLY.
• DO NOT USE THE GATE IF ANY COMPONENTS ARE DAMAGED OR MISSING.
• USE ONLY WITH THE LOCKING/LATCHING MECHANISM SECURELY ENGAGED.
• READ THE INSTRUCTIONS BEFORE INSTALLATION AS INCORRECT INSTALLATION CAN BE
• DANGEROUS.
• THIS PET GATE IS FOR DOMESTIC USE ONLY.

Maintenance

• Inspect regularly and remove if damaged.
• Clean the product with dampened soft fabric.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>